Toshiba DP1200 User manual

DIGITAL PLAIN PAPER COPIER
DP1200/1500
File No. 31100024

Copyright 2001
TOSHIBA TEC CORPORATION

CAUTION
This product is a class 1 laser product that complies with 21CFR 1040.10 and 1040.11 of the CDRH stand-
ard and IEC825. This means that this machine does not produce hazardous laser radiation. The use of
controls, adjustments or performance of procedures other than those specified herein may result in haz-
ardous radiation exposure.
This laser radiation is not a danger to the skin, but when an exact focusing of the laser beam is achieved
on the eye’s retina, there is the danger of spot damage to the retina.
The following cautions must be observed to avoid exposure of the laser beam to your eyes at the time
of servicing.
1) When a problem in the laser optical unit has occurred, the whole optical unit must be exchanged as
a unit, not as individual parts.
2) Do not look into the machine with the main switch turned on after removing the developer unit, toner
cartridge, and drum cartridge.
3) Do not look into the laser beam exposure slit of the laser optical unit with the connector connected
when removing and installing the optical system.
4) The middle frame contains the safety interlock switch.
Do not defeat the safety interlock by inserting wedges or other items into the switch slot.
LASER WAVE – LENGTH : 780 ∼795
Pulse times : 0.481 ms/6 mm
Out put power : 0.20 ±0.03 mW
CAUTION
INVISIBLE LASER RADIATION,
WHEN OPEN AND INTERLOCKS DEFEATED.
AVOID EXPOSURE TO BEAM.
VORSICHT
UNSICHTBARE LASERSTRAHLUNG,
WENN ABDECKUNG GEÖFFNET UND
SICHERHEITSVERRIEGELUNG ÜBERBRÜCKT.
NICHT DEM STRAHL AUSSETZEN.
VARO !
AVATTAESSA JA SUOJALUKITUS
OHITETTAESSA OLET ALTTIINA
NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE ÄLÄ
KATSO SÄTEESEEN.
ADVARSEL
USYNLIG LASERSTRÅLNING VED ÅBNING, NÅR
SIKKERHEDSBRYDERE ER UDE AF
FUNKTION. UNDGÅ UDSAETTELSE FOR
STRÅLNING.
VARNING !
OSYNLIG LASERSTRÅLNING NÄR DENNA DEL
ÄR ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.
BETRAKTA EJ STRÅLEN. – STRÅLEN ÄR FARLIG.
DP1200/1500

At the production line, the output power
of the scanner unit is adjusted to 0.57
MILLI-WATT PLUS 20 PCTS and is
maintained constant by the operation of
the Automatic Power Control (APC).
Even if the APC circuit fails in operation
for some reason, the maximum output
power will only be 15 MILLI-WATT 0.1
MICRO-SEC. Giving an accessible
emission level of 42 MICRO-WATT
which is still-less than the limit of
CLASS-1 laser product.
The foregoing is applicable only to the 220V
model
,
230V model and 240V model.
VAROITUS! LAITTEEN KÄYTTÄMINEN MUULLA
KUIN TÄSSÄ KÄYTTÖOHJEESSA MAINITULLA
TAVALLA SAATTAA ALTISTAA KÄYTTÄJÄN
TURVALLISUUSLUOKAN 1 YLITTÄVÄLLE
NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE.
VARNING - OM APPARATEN ANVÄNDS PÅ ANNAT
SÄTT ÄN I DENNA BRUKSANVISNING
SPECIFICERATS, KAN ANVÄNDAREN UTSÄTTAS
FÖR OSYNLIG LASERSTRÅLNING, SOM
ÖVERSKRIDER GRÄNSEN FÖR LASERKLASS 1.
Caution
This product contains a low power laser
device. To ensure continued safety do not
remove any coveror attempt to gain access
to the inside of the product. Refer all
servicing to qualified personnel.
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
DP1200/1500

CONTENTS
1. GENERAL ................................................................................................................... 1-1
1. DP1200/1500 major functions .......................................................................................... 1-1
2. System Configuration ....................................................................................................... 1-1
2. SPECIFICATIONS ....................................................................................................... 2-1
1. Basic specifications of copier ........................................................................................... 2-1
3. CONSUMABLE PARTS .............................................................................................. 3-1
1. Supply system table ......................................................................................................... 3-1
2. Environmental .................................................................................................................. 3-1
3. Production control number (lot No.) identification ............................................................. 3-1
4. TD cartridge replacement ................................................................................................. 3-2
4. EXTERNAL VIEWS AND INTERNAL STRUCTURES................................................ 4-1
1. Appearance ...................................................................................................................... 4-1
2. Internal ............................................................................................................................. 4-1
3. Operational panel ............................................................................................................. 4-2
4. Motors and solenoids ....................................................................................................... 4-3
5. Sensors and switches....................................................................................................... 4-4
6. PWB unit .......................................................................................................................... 4-5
7. Cross sectional view......................................................................................................... 4-6
5. UNPACKING AND INSTALLATION
1. A WORD ON COPIER INSTALLATION ............................................................................ 5-1
2. CHECKING PACKED COMPONENTS AND ACCESSORIES .......................................... 5-1
3. UNPACKING .................................................................................................................... 5-1
4. REMOVING PROTECTIVE PACKING MATERIALS ......................................................... 5-1
5. DEVELOPER UNIT INSTALLATION ................................................................................. 5-2
6. TONER CARTRIDGE INSTALLATION .............................................................................. 5-3
7. LOADING COPY PAPER ................................................................................................. 5-3
8. POWER TO COPIER ....................................................................................................... 5-4
9. CONNECTING THE INTERFACE CABLE (DP1200 Only) ............................................... 5-4
6. INSTALLING THE PRINTER DRIVER SOFTWARE (DP1200 Only) ......................... 6-1
1. Description of the printer driver ........................................................................................ 6-1
2. Checking the hardware and software requirements .......................................................... 6-1
3. Installing the printer driver ................................................................................................ 6-1
4. Printer driver group........................................................................................................... 6-3
5. Parallel interface ............................................................................................................... 6-3

7. OPERATIONAL DESCRIPTIONS ............................................................................... 7-1
1. Outline of operation .......................................................................................................... 7-1
2. Scanner section................................................................................................................ 7-2
3. Laser unit ......................................................................................................................... 7-2
4. Fuser section.................................................................................................................... 7-3
5. Paper feed section and paper transport section ............................................................... 7-4
6. Printing process ............................................................................................................... 7-7
8. DISASSEMBLY AND ASSEMBLY .............................................................................. 8-1
1. High voltage section ......................................................................................................... 8-1
2. Operation panel section.................................................................................................... 8-4
3. Optical section .................................................................................................................. 8-5
4. Fusing section .................................................................................................................. 8-6
5. Tray paper feed/Transport section..................................................................................... 8-9
6. Manual paper feed section ............................................................................................... 8-13
7. Rear frame section ........................................................................................................... 8-17
8. Power section ................................................................................................................... 8-18
9. ADJUSTMENTS .......................................................................................................... 9-1
1. Optical section .................................................................................................................. 9-1
2. Copy density adjustment .................................................................................................. 9-8
3. High voltage adjustment ................................................................................................... 9-9
10. SIMULATION,TROUBLE CODES .............................................................................. 10-1
1. Entering the simulation mode ........................................................................................... 10-1
2. List of simulations ............................................................................................................. 10-2
3. Contents of simulations .................................................................................................... 10-3
4. TROUBLE CODES........................................................................................................... 10-13
11. USER PROGRAM ....................................................................................................... 11-1
12. MAINTENANCE .......................................................................................................... 12-1
1. Maintenance table ............................................................................................................ 12-1
2. Maintenance display system ............................................................................................ 12-1
13. ELECTRICAL SECTION ............................................................................................. 13-1
1. Block diagram................................................................................................................... 13-1
2. Circuit descriptions ........................................................................................................... 13-3
14. CIRCUIT DIAGRAM .................................................................................................... 14-1

[1]GENERAL
1.DP1200/1500 major functions
Item CPM SB/MB 2 tray SPF (ADF) GDI without
USB
GDI with
USB
PCL6 with
USB SOPM
Model
DP1200 12CPM MB
DP1500 15CPM MB Opt Opt Opt Opt Opt
Descriptions of items
CPM: Copy speed (Copies Per Minute)
FAX: FAX unit. The GD-1100 (FAX unit) is optionally available.
SB/MB: SB = Manual feed single bypass, MB = Manual feed multi bypass
2 tray:Second cassette unit. The 1 tray unit (MY-1019) is optionally available.
SPF (ADF): Original feed unit (Automatic document feeder)
GDI with USB:GDI printer function with USB. The GA-1090 (GDI + USB kit) is optionally available.
SOPM:Scan One Print Many function (Many copies are made by one scan.)
PCL6 with USB:PCL printer function with USB. The GA-1100 (PCL6 + USB kit) is optionally available.
Descriptions of table
:Standard provision
:No function or no option available
Opt: Option
* PCL6 with USB (GA-1100) + FAX (GD-1100) is not available.
2. System Configuration
(Options)
FAX
MR-2013
MY-1019
GA-1090
(DP-1200/1500)
GA-1100
GD-1100
DP1200/1500
1 – 1

[2]SPECIFICATIONS
1.Basic specifications of copier
A.Basic specifications
ItemSpec.
TypeDesktop
Copy systemDry, electrostatic
Segment (class)Digital personal copier
External dimensions (W xD xH) (mm)DP1200: 293mm x518mm x445mm (TBD)
DP1500: 293mm x518mm x483mm (TBD)
WeightDP1200: Approx. 17.4kg (TBD)
DP1500: Approx. 19kg (TBD)
B.Operation specification
SectionItemDetailsSpec.
Paper
feed
section
Paper feed
systemDP1200, DP1500: 1 tray (250 sheets) + multi bypass (50 sheets)
AB system
Tray paper feed
section
Paper size A4, B5, A5 (Landscape)
Paper weight 56 – 80g/m2
Paper feed capacity 250 sheets
Kinds Standard paper, specified paper, recycled paper
Remark User adjustment of paper guide available
Multi bypass paper
feed section
Paper size A4, B5, A5, B6, A6 (Landscape)
Paper weight 52 – 128g/m2
Paper feed capacity 50 sheets
Kinds 1Standard paper, specified paper, recycled paper, OHP, Label,
Postal card
Remark User adjustment of paper guide available
Inch system
Tray paper feed
section
Paper size 8-1/2" x 14", 8-1/2 x11", 8-1/2" x 5-1/2"(Landscape)
Paper weight 15 – 21 lbs.
Paper feed capacity 250 sheets
Kinds Standard paper, specified paper, recycled paper
Remark User adjustment of paper guide available
Multi bypass paper
feed section
Paper size 8-1/2" x 14", 8-1/2 x11", 8-1/2" x 5-1/2", 3-1/2" x 5-1/2"
(Landscape)
Paper weight 14 – 34.5 lbs.
Paper feed capacity 50 sheets
Kinds 1Standard paper, specified paper, recycled paper, OHP, Label,
Postal card
Remark User adjustment of paper guide available
1:OHP, Label, Postal card: each 1 pc.
As special media have wide variety of forms by country or region, they may not be used in some cases.
DP1200/1500
2 – 1

Section Item Details Spec.
Paper exit section Exit way Face down
Capacity of output
tray 100 sheets
Originals
Original set Center Registration (left edge)
Max. original size B4 (10″×14″)
Original kindsSheet and book
Original size
detection None
Optical
section
Scanning
section
Scanning system CCD sensor scanning by lighting lamp scanner
CCD sensor Resolution 400 dpi
Lighting lamp Type Xenon lamp
Voltage 1.5kV
Power consumption 11 ±3W
Gradation 256 gradations/8bit
Writing
section Writing system Writing to OPC drum by the semiconductor laser
Laser unit Resolution 600 dpi
Image forming
Photoconductor Type OPC (30φ)
Life25k
Charger Charging system Saw -tooth charging with a grid, / (–) scorotron discharge
Transfer system (+) DC corotron system
Separation system (–) DC corotron system
Developing Developing system Dry, 2-component magnetic brush development system
Cleaning Cleaning system Counter blade system (Counter to rotation)
Fusing section
Fusing system Heat roller system
Upper heat roller Type Teflon roller
Lower heat roller Type Silicon rubber roller
Heater lamp Type Halogen lamp
Voltage100V/240V
Power consumption 800W
Electrical section
Power source Voltage Local AC voltage
Frequency Common use for 50 and 60Hz
Power consumption
Max.DP1200/DP1500: 1000W
Average (operating) *1)DP1500: 310Wh/H, DP1200: 270Wh/H
Stand-by mode
(initial condition) *1)DP1200/DP1500: 70Wh/H
Pre-heat mode *1)DP1200/DP1500: 40Wh/H
Auto power shut-off mode *1)DP1200/DP1500: 18Wh/H
*1) May fluctuate due to environmental conditions and the input voltage.
DP1200/1500
2 – 2

C.Copy performance
SectionItemDetailsSpec.
Copy magnificationFixed magnification ratios3R + 2E (AB system: 50, 70, 81, 100, 141, 200%)
(Inch system: 50, 64, 78, 100, 129, 200%)
Zooming magnification ratios50 ~200% (151 steps in 1% increments)
Manual steps (manual,
photo)5 steps
Copy speedFirst copy time
Tray paper feed
9.6 sec. or below (A4), 9.4 sec. or below (8-1/2"
14") (Pre-heat mode: 16 sec. or below / Auto power-
shut-off mode: 23 sec. or below)
Manual paper feed10.0 sec (Pre-heat mode: 16 sec. or below / Auto
power-shut-off mode: 23 sec. or below)
AB system: A4
(Landscape)Copy speed (CPM)
Same sizeDP1200: 12DP1500: 15
EnlargementDP1200: 12DP1500: 15
ReductionDP1200: 11DP1500: 15
B5 (Landscape)Copy speed (CPM)
Same sizeDP1200: 12DP1500: 15
EnlargementDP1200: 12DP1500: 15
ReductionDP1200: 12DP1500: 15
Inch system 8-1/2”
×14”(Landscape) Copy speed (CPM)
Same sizeDP1200: 10DP1500: 12
EnlargementDP1200: 10DP1500: 12
ReductionDP1200: 10DP1500: 12
8-1/2”×11”
(Landscape) Copy speed (CPM)
Same sizeDP1200: 12DP1500: 15
EnlargementDP1200: 12DP1500: 15
ReductionDP1200: 12DP1500: 15
Max. continuous copy
quantity 99
Void
Void area
Leading edge 1 4 mm
Trailing edge4 mm or less
Side edge void area 4 mm or less
(per side)
Image loss
OC mode Leading edge Same size: 3.0mm or less / Enlarge (200%): 2.0mm
or less / Reduction (50%): 6.0mm or less
SPF mode Leading edgeSame size: 4.0mm or less / Enlarge (200%): 3.0mm
or less / Reduction (50%): 8.0mm or less
DP1200/1500
2 –3

[3]CONSUMABLE PARTS
1.Supply system table
No. Name Model name Life Package unit Remark
1 Toner Cartridge PS-ZT1200 6.5K
25K
(6%)
25K
10 Life based on 6% coverage of A4 original.
2 Developer D-1200 10
3 Drum Kit OD-1200 10
2.Environmental
The environmental conditions for assuring the copy quality and the
machine operations are as follows:
(1) Normal operating condition
Temperature: 20°C~25
Humidity: 65 5%RH
(2) Acceptable operating condition
(3) Transportation condition
(4) Supply storage condition
3.Production control number (lot No.)
Production month
Production day
End digit of year
Version No.
Production month
Production day
End digit of year
Version No.
Destination code
(Dealer, distributor, OEM, etc.)
Production place
(SOCC: Fixed to B.)
Destination code
(Dealer, distributor, OEM, etc.)
Production place
(SOCC: Fixed to B.)
Production month
(1-9=Jan. -Sep. 0=Oct. X=Nov. Y=Dec)
Ver. A 9 1 1 0001 X
Serial number of month
Fixed to 1.
End digit of year
Version No.
Pack division
(See table below)
identification
áDeveloping cartridgeñ
*:Destination
Division No.
EX Destination A same pack G
B same pack H
Option Destination AP
BQ
áDrum cartridgeñ
The label on the drum cartridge shows the date of production.
(SOCC production)
áJAPAN productionñ
Humidity (RH)
85%
60%
20%
10°C 30°C 35°C
Humidity (RH)
90%
60%
15%
–25°C 30°C 40°C
Humidity (RH)
90%
20%
–5°C 45°C
DP1200/1500
3 – 1

Division No.
Ex production 1
Option 2
Same pack 3
∗1 The production control label is not attached to the cartridge of a
China product.
4. TD cartridge replacement
1) Open the front and side cabinets of the copier.
2) Keep holding Toner lover, and
3) Carefully pull out Toner unit from the copier.
4) Put Toner unit in a collection bag immediately after removing it from
the copier
Note: Never carry exposed Toner unit. Be sure to put it in the col-
lection bag.
Production control
label attachment position
Production control
label attachment position(*1)
1
3
2
DP1200/1500
3 – 2

[4] EXTERNAL VIEWS AND INTERNAL STRUCTURES
1. Appearance
(1) Original table (2) Original cover (3) Side cover
(4) Operation panel (5) Front cover (6) Paper tray
(7) Side cover open button (8) Paper guides (9) Handle
(10) Paper output tray (11) Paper output tray extension (12) Power cord socket
(13) Power switch
2. Internal
(1) TC cartridge lock release button (2) TD cartridge (3) Drum cartridge
(4) Drum cartridge handle (5) Paper feed roller (6) Fusing unit release lever
(7) Charger cleaner (8) Transfer charger
(1)
(4)
(6)
(5) (7)
(2)
(3)
(12)
(13) (9)
(9)
(8)
(10)
(11)
(8)
(1)
(2)
(3)
(4)
(5) (6) (7)
DP1200/1500
4 – 1

3. Operational panel
(1) Exposure mode selector key
and indicators (2) Light and dark keys and
exposure indicators (3) Alarm indicators∗1
(4) SPF indicator (5) SPF misfeed indicator (6) Copy ratio selector key and
copy ratio indicators
(7) Zoom indicator (8) Copy ratio display (%) key (9) Display
(10) ON LINE indicator (11) ON LINE key (12) DATA indicator
(13) Power save indicator (14) Tray select key (15) Paper feed location indicators
(16) Zoom keys (17) Copy quantity keys (18) Clear key
(19) Print key and ready indicator
∗1 Developer replacement required indicator
Misfeed indicator
Toner cartridge replacement required indicator
Maintenance indicator
∗2 ON: Indicates that the machine is in the energy saving (pre-heat) mode.
Blink: Indicates that the machine is in the process of resetting from the energy saving mode or just after supplying the power.
OFF: Indicates that resetting from the energy saving mode is completed and that the fusing temperature is in ready state.
The combinations of the above display lamps are as follows: (●= ON, ✕= OFF)
Lamp Immediately after power ON Ready Copying
Pre-heat lamp Blink ✕✕
Ready lamp ●●✕
Other lamps ●●●
Lamp Energy saving mode (Pre-
heating) Energy saving mode (Auto power shut off) Resetting from energy saving mode
Copy is started during
resetting from energy
saving mode
Pre-heat lamp ●●Blink Blink
Ready lamp ●✕●✕
Other lamps ●✕●●
Inch system
(1) (2) (3) (4) (5) (6)
(6)
(7) (8) (9) (10) (11) (12) (13)
(14) (15) (16) (17) (18) (19)
DP1200/1500
4 – 2

4. Motors and solenoids
No. Part name Control signal Function,operation
(1) Main motor MM Drives the copier.
(2) Mirror motor MRMT Drives the optical mirror base (scanner unit).
(3) Toner motor TM Supplies toner.
(4) Cooling fan motor VFM Cools the optical section.
(5) Resist roller solenoid RRS Resist roller rotation control solenoid
(6) Paper feed solenoid CPFS1 Cassette Paper feed solenoid
(7) Multi paper feed solenoid MPFS Multi manual pages feed solenoid
(1)
(2)
(3)
(4)
(5)
(7)
(6)
DP1200/1500
4 – 3

5. Sensors and switches
No. Name Signal Type Function Output
(1) Mirror home position
sensor MHPS Transmission sensor Mirror (scanner unit) home position detection “H” at home position
(2) POD sensor POD Transmissions sensor Paper exitdetection “H” at paper pass
(3) PPD2 sensor PPD2 Transmission sensor Paper transport
detection 2 “L” at paper pass
(4) Cassette detection
switch CED1 Microswitch Cassette installation
detection “H” at cassette insertion
(5) PPD1 sensor PPD1 Transmission sensor Paper transport
detection 1 “L” at paper pass
(6) Door switch DSW Micro switch
Door open/close
detection (safety switch
for 5V)
1 or 0V of 5V at door
open
(7) Door switch DSW Micro switch
Door open/close
detection (safety switch
for 24V)
1 or 0V of 24V at door
open
(1)
(2)
(3)
(4)
(5)
(6)
(7)
DP1200/1500
4 –4

6. PWB unit
No. Name Function
(1) Exposure lamp invertor PWB Exposure lamp (Xenon lamp) control
(2) Main PWB (MCU) Copier control
(3) Operation PWB Operation input/display
(4) Power PWB AC power input, DC voltage control, High voltage control
(5) CCD sensor PWB For image scanning
(6) LSU motor PWB For polygon motor drive
(7) TCS PWB For toner sensor control
(8) LSU PWB For laser control
(1) (2)
(3)
(4)
(5)
(7)
(6)
(8)
DP1200/1500
4 – 5

7. Cross sectional view
No. Part name Function and operation
(1) Scanner unit Illuminates the original with the copy lamp and passes the reflected light to the lens unit
(CCD).
(2) Exposure lamp Exposure lamp (Xenon lamp) Illuminates original
(3) Lens unit Scans the original image with the lens and the CCD.
(4) LSU (Laser unit) Converts the original image signal into laser beams and writes onto the drum.
(5) Paper exit roller Roller for paper exit
(6) Main charger Provides negative charges evenly to the drum surface.
(7) Heat roller Fuses toner on the paper. (Teflon roller)
(8) Pressure roller Fuses toner on the paper. (Silicon rubber roller)
(9) Drum Forms images.
(10) Transfer unit Transfers images onto the drum.
(11) Pickup roller Picks up the manual feed paper. (In multi feed only)
(12) Manual paper feed
tray Tray for manual feed paper
(13) Manual paper feed
roller Transport the paper from the manual paper feed port.
(14) PS roller unit Takes synchronization between the lead edge and the rear edge of the paper.
(15) Paper feed roller Picks up a sheet of paper from the cassette.
(2) (4)
(1) (3)
(5) (6)
(7)
(8)
(9)
(10)
(11)
(13) (12)
(14)
(15)
DP1200/1500
4 – 6

[5] UNPACKING AND INSTALLATION
1. A WORD ON COPIER INSTALLATION
Improper installation may damage the copier. Please note the
following during initial installation and whenever the copier is
moved.
Do not install your copier in areas that are:
●damp, humid, or very dusty
●exposed to direct sunlight
●poorly ventilated
●subject to extreme temperature or humidity changes, e.g.,
near an air conditioner or heater.
Be sure to allow the required space around the machine for
servicing and proper ventilation.
2. CHECKING PACKED COMPONENTS AND
ACCESSORIES
Open the carton and check if the following components and ac-
cessories are included.
3. UNPACKING
Unpack the copier and carry it to the installation location by
holding the handles on both sides of the copier.
4. REMOVING PROTECTIVE PACKING
MATERIALS
1) Remove pieces of tape (a), (b), (c), (d) and (e) and protec-
tive cover (f). Then open the original cover and remove
protective materials (g) and (h).
8"(20cm)
4"
(10cm) 4"
(10cm)
8"(20cm)
a
b
c
e
h
f
g
d
Copier
Power cord
Drum cartridge
(installed in copier)
Operation manual
(CD-ROM :DP1200 Only)
DP1200/1500
5 – 1

2) Use a coin (or suitable object) to remove the screw.
Store the screw in the paper tray because it will be used if
the copier has to be moved.
3) Open the bypass tray and then open the side cover whilst
pressing the side cover open button.
4) Remove the CAUTION tape from the front cover and
remove the two protective pins from the fusing unit by pull-
ing the strings upward one at a time.
5. DEVELOPER UNIT INSTALLATION
1) 2) 3) Open the side and front cabinets of the copier.
4) Remove the locking tape of the developer unit.
5) Remove the screw which is fixing the copier and
Developer unit.
6) Remove Developer unit slowly from the copier.
7) Remove the screw (1 pc).
8) Remove Upper developer unit.
9) Shake the aluminum bag to stir developer
10) Supply developer from the aluminum bag to the top of the
MX roller evenly.
Note: Be careful not to splash developer outside Developer
unit.
11) Attach Upper developer unit and fix it with a screw.
12) Rotate the MG roller gear to distribute developer evenly.
Note: Never rotate the gear in the reverse direction.
Note: When carrying Developer unit, do not tilt it extremely
as shown with the arrow in the figure below.
(Prevention of splash of developer)
2
4
5
3
1
Protective pins
CAUTION tape
DP1200/1500
5 – 2