Toshiba e-studio15 User manual

Your fax machine and the telephone system
WARNING NOTICE:
NO calls can be made to or from this fax during a mains power failure.
WARNING — Australian Communications Authority (ACA) regulations state that no
unauthorised changes or modifications to this equipment are permitted.
Note:Complies with the following standards,
ACATS001-1997, AS/NZS 3260
ACATS002-1997 and AS/NZS 3548.
These limits are designed to provide reasonable protection against interference in an
installation.This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause interference.However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and the receiver.
— Connect the equipment to an outlet on a different circuit to that which the receiver is
connected.
— Consult the dealer or an experienced radio/TV technician for help.
The Ringer Equivalence Number (REN) for this equipment is written on the A-Tick label.
Important safety information
Installing or modifying telephone lines should only be done by an ACA licensed serviceman.
Note: In some areas a distinctive ring pattern can be provided by the telephone
companies for modems.The fax cannot use the distinctive ring pattern that is in use
for the modem.

i
1. INSTALLATION
Quick Reference Guide ...........................................................................................1-1
Introduction..............................................................................................................1-2
Choosing a Location................................................................................................1-2
Parts Identification ...................................................................................................1-3
Connections ............................................................................................................1-4
Connecting theTelephone Line Cord...................................................................1-4
Final Preparations ...................................................................................................1-5
Connecting Other Devices...................................................................................1-5
2. INITIAL SETTINGS
A Look at the Fax Control Panel ..............................................................................2-1
About the Liquid Crystal Display..............................................................................2-2
Using the Arrow Keys ..............................................................................................2-2
Adjusting the BeepVolume......................................................................................2-2
Adjusting the RingingVolume ..................................................................................2-3
Setting the Length of Alarm Beeps ..........................................................................2-3
Turning Key Beeps Off.............................................................................................2-4
Fax Setup ................................................................................................................2-5
How to Enter Characters .....................................................................................2-5
EnteringYour Name and Fax Number .................................................................2-6
Setting the Date andTime ...................................................................................2-7
Selecting the Reception Mode.............................................................................2-8
Setting the Number of Rings for Auto Reception .................................................2-9
Setting the Number of Rings for Manual Reception .............................................2-9
Selecting the Reception Paper Size...................................................................2-10
Setting theTray Paper Size................................................................................2-11
Setting the Dial Mode ........................................................................................2-12
Setting the Number of RecallTimes ..................................................................2-12
Setting the Recall Interval..................................................................................2-13
Setting the Index Function .................................................................................2-14
Setting Fine Resolution Priority .........................................................................2-15
Setting Up the Unit for Use with a PC Modem ...................................................2-15
Using the Remote Reception Function ..............................................................2-16
Distinctive Ringing ............................................................................................. 2-18
Storing Numbers for Automatic Dialling .............................................................2-19
Chain Dialling for Long Numbers ...................................................................2-21
Storing Numbers Under Group Keys .................................................................2-22
Using the Unit with an Answering Machine............................................................2-24
Quiet DetectTime..............................................................................................2-24
Answering Machine Backup .............................................................................. 2-25
3. CHOOSING SUITABLE MEDIA
Originals Suitable for Faxing....................................................................................3-1
Size andWeight...................................................................................................3-1
Unsuitable Originals ............................................................................................3-2
TABLE OF CONTENTS

ii
4. HOWTO USETHE FAX FUNCTION
Sending Documents ................................................................................................4-1
Setting the Document ..........................................................................................4-1
OptionalTransmission Settings............................................................................4-3
Resolution .......................................................................................................4-3
Contrast...........................................................................................................4-3
Cover Sheet ....................................................................................................4-4
Auto Cover Sheet ............................................................................................4-5
Dialling andTransmitting......................................................................................4-6
Direct Keypad Dialling .....................................................................................4-6
Rapid Key Dialling ...........................................................................................4-7
SpeedDialling .................................................................................................4-7
Chain Dialling ..................................................................................................4-8
Normal Dialling Using the SPEAKER key........................................................4-8
Using the SEARCH Key ..................................................................................4-9
Redialling ........................................................................................................4-9
Receiving Faxes ....................................................................................................4-10
Using AUTO Mode.............................................................................................4-10
Using MANUAL Mode .......................................................................................4-10
Using A.M. Mode ...............................................................................................4-10
Optional Reception Settings ..................................................................................4-11
Receive Reduce ................................................................................................4-11
Footer Printing...................................................................................................4-12
When using manual sending and receiving ...........................................................4-12
Special Functions ..................................................................................................4-13
Memory .............................................................................................................4-13
Substitute Reception into Memory.................................................................4-13
Data Transfer ..................................................................................................... 4-14
Transmission Reservation .................................................................................4-15
Broadcasting .....................................................................................................4-17
Polling................................................................................................................4-19
Setting the Polling Key...................................................................................4-19
Polling Others ................................................................................................4-19
Being Polled (Memory Polling).......................................................................4-20
Timer Operations...............................................................................................4-22
Anti Junk Fax.....................................................................................................4-24
Printing Out Reports..............................................................................................4-26
Activity Report Auto Listing................................................................................4-28
PrintingTransaction Reports..............................................................................4-28
5. TROUBLESHOOTING
Troubleshooting .......................................................................................................5-1
Messages and Signals ............................................................................................5-2
Display Messages ...............................................................................................5-2
Audible Signals....................................................................................................5-3
6. SPECIFICATIONS
GLOSSARY
INDEX
TABLE OF CONTENTS

1-1
INSTALLATION
1. INSTALLATION
This page summarizes the operations you can perform with this unit.For detailed
information about each operation, refer to the appropriate section of this manual.
QUICK REFERENCE GUIDE
BROADCASTING
TRANSMITTING DOCUMENTS
Set RESOLUTION/CONTRAST
Normal Broadcasting
BROADCAST Enter Speed Dial number/
Press Rapid keys FAX START
Using Group Key
Press GROUP key
POLLING OTHERS
Set Rapid 20 key as polling key
(FUNCTION key 3 4 1 STOP STOP)
Direct Keypad Dialling
Dial (press NUM keys) POLLING (Rapid 20)
Speed Dialling
SPEED Enter Speed Dial number
POLLING (Rapid 20)
Normal Dialling
SPEAKER Dial (Press NUM keys)
Wait for reception tone POLLING (Rapid 20)
Load the document then follow
the appropriate procedure
Set RESOLUTION CONTRAST/Memory or Direct
Direct Keypad Dialling
Dial (press NUM keys) FAX START
Rapid Key Dialling
Press Rapid key
Speed Dialling
SPEED/ SEARCH Enter Speed Dial number FAX START
Nomal Dialling
SPEAKER Dial (Press NUM keys)
Wait for reception tone FAX START
Redialling
REDIAL Wait for reception tone FAX START
FAX
FUNCTION MODE
STEP 1
STEP 2 Press FUNCTION key
Press the menu number
from the list below STEP 3 Press the option number
from the list below
1.OPERATION SET (SEND/POLLING) 2.OPERATION CLEAR
1.TRANSMISSIONS ACTIVITY REPORT 2.RECEPTIONS ACTIVITY REPORT
3.TIMER LIST 4.TELEPHONE LIST
5.OPTION SETTING LIST 6.GROUP LIST
7.ANTI JUNK FAX NUMBER LIST
1.FAX NUMBER MODE (SET/CLEAR) 2.DATE & TIME SET
3.OWN NUMBER SET 4.POLLING FUNCTION (ON/OFF)
01.OUTPUT PAPER SIZE SELECT 02.PAPER SIZE SETTING
03.FINE RESOLUTION PRIORITY 04.NUMBER OF RINGS AUTO RECEPTION
05.NUMBER OF RINGS MANUAL RECEPTION
07.TRANSACTION REPORT PRINT SELECT 08.RECALL TIMES
09.RECALL INTERVAL 10.FAX REMOTE NUMBER
11.REMOTE RECEPTION SELECT 12.FAX SIGNAL AUTO RECEIVE
13.AUTO COVER SHEET 14.RECEIVE REDUCE
15.BEEP LENGTH 16.BEEP VOLUME
17.KEY BEEPS 18.INCOMING RING VOLUME
19.DIAL MODE 20.DISTINCTIVE RINGING
21.FOOTER PRINT 22.BATCH INDEXING
1.GROUP SET MODE 2.GROUP CLEAR MODE
1.ANTI JUNK SELECT (ON/OFF) 2.JUNK FAX NUMBER MODE (SET/CLEAR)
1.COVER SHEET ON 2.COVER SHEET OFF
1.QUIET DETECT TIME 2.SELECT AUTO RECEIVE(ON/OFF)
1.1-TIME 2.REPEAT
1.TIMER MODE
2.LISTING MODE
3.ENTRY MODE
4.OPTION SETTING
5.GROUP ENTRY MODE
6.ANTI JUNK FAX MODE
7.COVER SHEET MODE
8.
ANSWERING MACHINE MODE
9. MEMORY POLL MODE
0. RECEIVE DATA TRANSFER MODE
1.DATA TRANSFER 2.FAX NUMBER
06.ACTIVITY REPORT AUTO LISTING

1-2 INSTALLATION
Choosing a Location
All electrical equipment is potentially dangerous if not installed and operated correctly.
Make sure that you meet the following requirements when you set up or move the unit.
• The unit must be installed on a level
surface.
• Use only the rated voltage from a
properly grounded wall socket.
• Keep the unit away from areas that are:
- Dusty or smoky
- Damp or humid
- Poorly ventilated
- In front of windows or extremely
bright light
- In direct sunlight
- Subject to other extreme conditions
• Provide ample room for easy access to
the front, back, and sides of the unit.
• Leave enough space around the
ventilation outlets for heat from the fan
to dissipate properly. Blocking these
outlets could cause the unit to
overheat, which can cause serious
damage to the internal parts.
• Use of extension cords is not
recommended.
Fan
This manual describes how to use the fax function of the unit.
Part names and functions shared with the copy function (for example, the misfeed
indicatorand add paperindicator), are described in thecopier operator’s manual.
For moreinformation, please readthe copier operator’s manual.
Introduction

1-3
INSTALLATION
Parts Identification
Fax control panel

1-4 INSTALLATION
Connections
Plug one end of the telephone line cord into the socket on the unit marked“TEL LINE.”
Plug the other side into the adapter.
Plug the adapter into the telephone socket on the wall.
Note: If your area experiences a high incidence of lightning or power surges, we
recommend that you install surge protectors for the power and telephone lines.
Surge protectors can be purchased from your dealer or at most telephone
specialtystores.
TEL
LINE
Connecting theTelephone Line Cord

1-5
INSTALLATION
Final Preparations
If desired, an answering machine or external telephone can be connected to the
adapter.
Connecting Other Devices
•Connecting an answering machine to the unit allows you to receive both voice and fax
messages when you are out.To use this feature, first change the outgoing message
of your answering machine, and then set the reception mode of the unit to“A.M.”
(Answering Machine mode) when you go out.
Note: If you are using distinctive ringing with an answering machine, you do not need
to follow the procedure described below.(Please note that when distinctive
ringing is used, the answering machine must be distinctive ring compatible.
The outgoing message of your answering machine should be changed to inform callers
who want to send a fax to press their FAX START key.
Comments:
1. It is advisable to keep the length of the message under 10 seconds.If it is too long,
you may have difficulty receiving faxes sent by automatic dialling.
2. Your callers can even leave a voice message and send a fax message on the same
call.Modify your outgoing message to explain that this can be done by pressing their
FAX START key after leaving their voice message.
•You can connect an extension phone in series with the adapter to make and receive
calls.Even if you pick up the extension phone and hear a fax tone, the unit will
automatically cut in and take over the line.Note, however, if you also have a PC
modem on the same line with the extension phone, you must turn on the Remote
Reception function, and deactivate the Fax Signal Receive function.See “Setting Up
the Unit for Use with a PC Modem”and “Using the Remote Reception Function”in
Chapter 2.
Note: The Remote Reception function is initially set to “ON”.

1-6 INSTALLATION
Notes

INITIAL SETTINGS 2-1
A Look at the Fax Control Panel
01 02 03 04 05
06 07 08 09 10
11 12 13 14 15
16 17 18 19 20/POLL
AUTO
MANUAL
A.M.
DEF
MNO
WXYZ
ABC
JKL
TUV
GHI
PQRS
SPEAKER
BOOK SEND
DOCUMENT
FAX STARTSTOP
REDIAL/PAUSE
SPEED/SEARCH
ENTER
RESOLUTION CONTRAST BROADCAST RECEPTION MODE
FUNCTION
Number keys
Press these keys to dial
numbers, and enter
numbers and letters
during number/name
storing procedures.
Rapid keys
Press one of these keys to
dial a fax or telephone
number automatically.
Press Rapid key 20 to start
polling if programmed.
(Note that you must attach
the Rapid key labels.)
FAX START key
Press this key to begin
sending a fax or manually
receiving a fax.
ENTER key
Press this key to decide an
item in a menu, or to enter
numbers and letters you
have typed in.
LCD contrast dial
Turn this dial to adjust the
contrast level of the LCD.
DOCUMENT key
Press this key to perform a
direct send fax transmission.
SPEED/SEARCH key
Press this key to dial a two
digit Speed Dial number.
During character inputting,
use this key to delete an
incorrect entry.
Also, press this key twice to
search for an automatic
dialling number.
RECEPTION MODE key
Press this key to select
the mode of reception.
REDIAL/PAUSE key
Press this key to
automatically redial the last
number you dialed. Also,
press this key to insert a
pause when entering
numbers.
FUNCTION key
Press this key to
enter function
mode.
Liquid crystal display
Shows various messages during fax
operation and programming.
BROADCAST key
Press this key to send
documents to a group of
receiving fax machines.
RESOLUTION key
Press this key to
adjust the resolution
before sending faxes.
SPEAKER key
Press this key to begin
manual dialling. (To close the
line, press the SPEAKER
key again.)
AUTO light
This light indicates that the
machine will answer the call
automatically.
MANUAL light
This light indicates that the
machine must be answered
manually.
A.M. light
This light indicates the
answering machine will answer
the line if properly connected.
CONTRAST key
Press this key to adjust
the contrast before
sending faxes.
BOOK SEND key
Press this key to fax a
document from the
original table.
STOP key
Press this key to stop an operation
before it is completed, or to delete
the number that was last input.
This key is also used to close the
line when manually dialling.
/
Press these keys to enter
symbols during the name
storing procedure.
Press the " " key to
change
from pulse dialling to tone
dialling mode.
Left arrow key ( ) and right arrow key ( )
Press these keys to scroll through a menu. During input
mode, these keys are also sometimes used to move
the cursor.
2. INITIAL SETTINGS

INITIAL SETTINGS
2-2
STOP
About the Liquid Crystal Display
The unit is equipped with a two-line liquid crystal display (LCD) on the operation panel
for displaying various messages and settings during operation.This LCD can display
up to 20 characters on each line.When the unit is idle, the LCD shows the date, time,
and the stand-by memory available.
Example:
Adjust the volume of both key beeps and alarm beeps (emitted at the end of transmission
and reception) using the procedure below.
Factory setting:3 (MEDIUM)
Step Press these keys Comments
1“OPTION SETTING”will appear in
the display.
2“BEEPVOLUME”will appear in the
display.
3Press the or key to lower or raise
the volume to the desired level.
4“STORED”will appear in the display.
5Press the STOP key twice to exit.
FUNCTION
GHI
MNO
or
ENTER
STOP
Adjusting the Beep Volume
The left and right arrow ( ) keys on the operation panel of the unit are very useful
for scrolling through the various function lists and settings.Once you have pressed the
FUNCTION key, you can scroll through the ten functions as desired. (See the Function
mode at the top of the Quick Reference Guide for the settings.) Pressing the ENTER
key chooses the displayed function.For many of the function lists, you can then use the
arrow keys again to scroll through the settings.
Using the Arrow Keys
Located to the upper right of the operation panel, the LCD contrast dial controls the
contrast of the display.
Turning the dial to the right darkens the LCD.Turning the dial to the left lightens the
LCD.

INITIAL SETTINGS 2-3
Adjust the ringing volume of the unit using the procedure below.
Factory setting:3 (MEDIUM)
Step Press these keys Comments
1“OPTION SETTING”will appear in
the display.
2“RINGINGVOLUME”will appear in
the display.
3Press the or key to lower or raise
the volume to the desired level.
4“STORED”will appear in the display.
5Press the STOP key twice to exit.
Adjusting the RingingVolume
FUNCTION
GHI
TUV
or
ENTER
STOP
STOP
You can select the length in seconds of the alarm beeps following the procedure
below.
Factory setting:1 (3SEC)
Step Press these keys Comments
1“OPTION SETTING”will appear in
the display.
2“BEEP LENGTH”will appear in the
display.
3Press the or key to set the alarm
beeps to the desired length or to turn
themoff.
4“STORED”will appear in the display.
5Press the STOP key twice to exit.
Setting the Length of Alarm Beeps
FUNCTION
GHI
JKL
or
ENTER
STOP
STOP

INITIAL SETTINGS
2-4
If you prefer, you can choose to turn the key beeps off.To do this, follow the
procedure below:
Factory setting:1 (ON)
Step Press these keys Comments
1“OPTION SETTING”will appear in
the display.
2“KEY BEEPS”will appear in the
display.
3Press 1to turn the key beeps on, or 2
to turn them off.
4Press the STOP key twice to exit.
Turning Key Beeps Off
FUNCTION
GHI
PQRS
or
ABC
STOP
STOP

INITIAL SETTINGS 2-5
Fax Setup
You can enter letters with the number keys.Letters are marked above each of the
number keys “2”through “9”.To enter a letter, press the appropriate key repeatedly until
the desired letter appears (the number of the key appears first, followed by letters in the
order marked above the key).The keys used for entering characters are shown below.
•To enter two characters in succession which require using the same key, press the
right arrow ( ) key once after entering the first character, and then enter the second
character.
•To change one individual character to another, move the cursor to the character you
want to change and enter the new one.The new character will replace the old one.
•Symbols can also be entered by pressing the “#”and “ ” keys:
•Pressing the “1” key on the number keypad enters a space.
How to Enter Characters
GHI
PQRS
ABC
JKL
TUV
DEF
MNO
WXYZ

INITIAL SETTINGS
2-6
Note: You can view all of the items in the menu display by pressing the FUNCTION
key, then using the left and right arrow ( ) keys to scroll through the function
list.Pressing the ENTER key chooses the displayed function.Procedures for
inputting various items (name, telephone number, date, etc.) are given as
follows.
To have your name and fax number printed at the top of every page you transmit,
program them by pressing the operation panel keys as shown below.
•If you enter an incorrect character, press the left arrow () key to move the cursor
back to the mistake, then enter the correct character.(To move the cursor forward,
press the right arrow ( ) key.)
Use the following procedure to enter your name and fax number:
Step Press these keys Comments
1“ENTRY MODE”will appear in the
display.
2“ENTERYOUR FAX #”will appear in
the display.
3Enter your own fax number (maximum
20 digits) by pressing the number keys.
To insert a space between digits, press
the “ ”key.To insert a “+”, press the“#”
key.
(example:18002374277)
4“ENTERYOUR NAME”will appear in
the display.
5Enter your name by pressing the
appropriate number keys as shown
on the left.Press each key repeatedly
until the desired letter appears in the
display (maximum of 24 characters).
To enter a space, press the 1key
twice.To switch between lower case
and capital letters, press the REDIAL/
PAUSE key once.
(example:TOSHIBA)
6“STORED”will appear in the display.
7Press the STOP key twice to exit.
EnteringYour Name and Fax Number
FUNCTION
DEF
TUV
ABC
DEF
PQRS
ENTER
STOP
STOP
ENTER
DEF
GHI
ABC
PQRS PQRS
Fax Setup
TUV TUV
MNO MNO MNO MNO
PQRS PQRS PQRS PQRS PQRS
GHI GHI GHI
GHI GHI GHI GHI
ABC ABC ABC
ABC ABC

INITIAL SETTINGS 2-7
The date and time that appear in the display are printed at the top of each page you
transmit.Set the date and time by pressing the keys on the operation panel as shown
below.To correct a mistake, press the STOP key to move the cursor back to the
mistake, and then enter the correct number.
Note: The unit supports millennial dates (those from the year 2000 on).To program
such a date, enter the last two digits;for example, the year 2000 is programmed
by entering “00”.
Use the following procedure to set the date and time:
Step Press these keys Comments
1“ENTRY MODE”will appear in the
display.
2“ENTERYEAR”will appear in the
display.
3Enter the last two digits of the year.
“ENTER MONTH”will appear in the
display.
(example:1999)
4Enter the month (2 digits:“01”for
January, “02”for February, “12”for
December, etc.).“ENTER DATE”will
appear in the display.
(example: July)
5Enter the day of the month (“01”to
“31”).“PRESS ENTER KEY”will
appear in the display.
(example:the fifth)
6“ENTERTIME”will appear in the
display.
7Enter the hour (2 digits:“01”to “12”).
8Enter the minute (2 digits:“00”to“59”).
9Press “ ” to select A.M., or “#”to
select P.M.“PRESS ENTER KEY”will
appear in the display.
10 The clock starts when you press this
button.“STORED”will appear in the
display.
11 Press the STOP key twice to exit.
DEF
ABC
or
STOP STOP
ENTER
Setting the Date andTime
FUNCTION
DEF
JKL
WXYZ WXYZ
ENTER
ABC
PQRS
Fax Setup

INITIAL SETTINGS
2-8
Your unit has three modes for receiving incoming calls and faxes:
• AUTO mode:
Select this mode when you only want to receive faxes on your telephone line.The unit
will automatically answer all calls and receive incoming faxes.
• MANUAL mode:
This is the most convenient mode for receiving phone calls if you have an extension
phone.To have true manual mode, the unit must be set to not answer while in MANUAL
mode (see“Setting the Number of Rings for Manual Reception”on the next page).You
can also receive faxes;however, all calls must first be answered by picking up the
receiver on the extension phone.
• A.M. mode:
Select this mode when an answering machine is connected to the unit and you want
the answering machine to answer all calls.This allows you to receive both voice
messages and faxes while you are out.
Note: If you are using distinctive ringing as described in “Distinctive Ringing”in this
chapter, you must set the reception mode to AUTO.This is true, as well, if you
are using an answering machine with distinctive ringing (in this case, the
answering machine must be connected to a separate wall socket, not to your
unit).
To set the reception mode, press the RECEPTION MODE key until the light next to the
desired mode comes on.
For more information on reception modes, refer to Chapter 4.
AUTO
MANUAL
A.M.
BOOK SEND
RESOLUTION CONTRAST BROADCAST
FUNCTION
ENTER
RECEPTION MODE
Selecting the Reception Mode
Fax Setup

INITIAL SETTINGS 2-9
You can set the number of rings before the unit answers in AUTO mode using the
procedure below.
Factory setting:2
Step Press these keys Comments
1“OPTION SETTING”will appear in
the display.
2“# OF RINGS(AUTO)”will appear in
the display.
3Select the number of rings you would
like to use (0to 9).
4“STORED”will appear in the display.
5Press the STOP key twice to exit.
Setting the Number of Rings for Auto Reception
FUNCTION
GHI
GHI
ENTER
STOP STOP
WXYZ
to
The number of rings before the unit answers in MANUAL mode can also be set.If you
do not want the unit to answer at all in MANUAL Mode, select“0” in Step 3 below.
Factory setting: 0 (OFF)
Step Press these keys Comments
1“OPTION SETTING”will appear in
the display.
2“# OF RINGS(MAN.)”will appear in
the display.
3Select the number of rings you would
like to use (0to 9).
4“STORED”will appear in the display.
5Press the STOP key twice to exit.
Setting the Number of Rings for Manual Reception
FUNCTION
GHI
JKL
ENTER
STOP STOP
WXYZ
to
Fax Setup
Note: If an external telephone is connected, the external telephone will ring one time
when auto reception is set to 0 rings.

INITIAL SETTINGS
2-10
Fax Setup
On the control panel, you can select the paper size that you want received faxes to be
printed on (AUTO, A4, Letter, Legal).If you select the AUTO setting the unit
automatically prints the fax out on the most appropriate size paper.
Follow the procedure below:
Factory setting:4 (AUTO)
Step Press these keys Comments
1“OPTION SETTING”will appear in
the display.
2“PRINT PAPER SIZE”will appear in
the display.
3Press 1for letter, 2for legal, 3for A4,
or 4for AUTO.“STORED”will appear
in the display.
4Press the STOP key twice to exit.
Note: If the size setting on the control panel differs from the size actually in the paper
trays, the error message“PAPER OUT (XX)”appears on the display (for
example, if you have set A4 on the control panel and the paper trays contains
letter-size and legal-size paper).When this happens, the received fax is saved
in memory and printed when you do either of the following.
• Correct the setting on the control panel
• Put paper of the selected size in the paper tray and set the size with function
(See the section “Setting the Tray Paper Size”)
Selecting the Reception Paper Size
FUNCTION
GHI
or
ABC
STOP
STOP
or
DEF
or
GHI