Total Gym 1100 User manual

— 12 —
TOTAL GYM®1100 PARTS LIST & EXPLODED DRAWING
24
23
22
28
27 29
21
27
24
26
26
25
PART # PART DESCRIPTION QTY.
1 Vertical Column 1
2 Tube Rollers 2
3 Stoppers 4
4 Screws 3
5 Washers 14
6 Nuts 7
7 Screws 4
8 Upper Rail (right & left) 1
9 Center Support Rail 1
10 Rectangular Tube Caps 6
11 Plastic Bushings 4
12 Shaft 1
13 Lower Rail 1
14 Platform 1
15 Platform Rail 1
PART # PART DESCRIPTION QTY.
16 Left Fender 2
17 Right Fender 2
18 Fender Bolts 4
19 Wheels 4
20 Wheel Spacer Tube 4
21 Adjustment Tube 1
22 Plastic Slide Bushing 1
23 Square Tube Cap 1
24 Round Tube Caps 6
25 Eyebolts 2
26 Eyebolt Nuts 2
27 Nut Caps 2
28 Spring-Loaded Pin 1
29 “C” Pin 1
30 Cable Assembly 1
PART # PART DESCRIPTION QTY.
31 Pulley Assembly 4
32 Handle Assembly 2
33 Multi Function Attachment 1
34 Grips 2
35 Foam Pads 2
36 Pins 3
37 Leg Pulley 1
38 Bracket 1
39 “D” Ring 1
40 Harness 1
LITERATURE PAC
41 Owner’s Manual 1
42 Exercise Booklet 1
43 Warranty Card 1
50 Safety Hitch Pin 1
A
Congratulations on purchasing your new
Total Gym®1100.
With this product in your home, you have everything you need to start your own workout program, to
tone and strengthen the important muscle groups of your upper and lower body.This is vital for all of us,
regardless of age, sex, or fitness level, and regardless of whether your primary goal is body sculpting,
weight loss, health maintenance, or more energy for daily activities.
Strength training not only tones and conditions the muscles we use every day to stand, walk, lift, and
turn; it can actually transform our body composition. By reducing body fat and increasing the proportion
of lean muscle in our bodies, strength training can effectively turn up our metabolic thermostat, so that
we burn calories all the time, no matter what we’re doing.
It’s easy-all you have to do is spend 15 to 20 minutes a day, 3 to 4 days per week on your Total Gym®
1100 to start realizing the benefits.
Be sure to read through this Owner’s Manual carefully. It is the authoritative source of information
about your Total Gym®1100.
If you have questions about your Total Gym®1100, please call Customer Service at
1-800-303-7896,Monday through Friday, 8:30am to 5:00pm, EST.
Please do not call the above number for Parts. See Ordering Replacement Parts section below.
Table of Contents
Safety Instructions & Warnings . . . . . . . . . . . . . . . . . . . . . . . . . .2
ProductSpecifications ................................3
SetUp............................................4-5
Accessories .......................................6-8
StartingOut.........................................9
Inspection, Maintenance & Storage . . . . . . . . . . . . . . . . . . .10-11
Parts List & Exploded Drawing . . . . . . . . . . . . . . . . . . . . . . . . .12
ORDERING REPLACEMENT PARTS
hen ordering parts, please contact our Parts Department, toll free at 1-800-303-7896, Monday
through Friday, 8:30am to 5:00pm, EST.
IMPORTANT: You must have your serial number and this manual ready when calling for parts.
Serial #: ____________________________
Please also provide the following information:
1) Name, Mailing Address and Telephone Number
2) Date of Purchase
3) Where Product was Purchased (Name of Retail Store, City)
4) Model Number (Total Gym 1100)
5) Part Order Number and Description
To order optional accessories, please go to www.totalgymcatalog.com

— 11 —
— 2 —
FAILURE TO READ AND FOLLOW THE SAFETY INSTRUCTIONS STATED IN THE
OWNER’S MANUAL MAY RESULT IN POSSIBLE SERIOUS INJURY OR DEATH.
KEEP CHILDREN AWAY. MA IMUM USER WEIGHT 275 LBS.
REPLACE THIS LABEL IF DAMAGED, ILLEGIBLE OR REMOVED. CLASS HC.
MAKE SURE ADJUSTMENT PIN IS LOCKED IN PLACE BEFORE BEGINNING E ERCISES.
CRUSH HAZARD, KEEP HANDS CLEAR DURING FOLDING.
KEEP HAIR, FINGERS, LOOSE CLOTHING, PETS, AND CHILDREN AWAY FROM HINGES
AND OTHER MOVING PARTS TO AVOID SERIOUS INJURY. ALSO, BE SURE TO HAVE ALL
PINS LOCKED IN PLACE BEFORE GETTING ON YOUR TOTAL GYM®
TO AVOID SEVERE INJURY.
BE CAREFUL NOT TO BUMP HEAD WHEN LEG ATTACHMENT IS IN PLACE.
REMOVE MULTI FUNCTION ATTACHMENT FROM FRAME WHEN NOT REQUIRED
FOR THE SPECIFIC E ERCISE.
Warning Label 1.
Warning Label 2.
Warning Label 3.
(3 locations)
Caution Label 2.
Warning Label 4.
Caution Label 1.
Warning Label 5.
(4 locations)
WARNING
WARNING
WARNING
CAUTION
WARNING
PINCH POINT. KEEP HANDS AWAY FROM THE FENDER.
Before beginning this or any exercise program, consult a physician or health professional, who can assist you
in planning a program appropriate for your age and physical condition.This is especially important if you are over age
35 or have pre-existing health problems.
Do not overexert yourself. Stop exercising immediately and consult your doctor if you experience pain or tightness in
your chest, irregular heart beat, shortness of breath, or if you feel faint, nauseous, or dizzy.
This product is designed for home use only. It is not intended for commercial or institutional use. Use only as
instructed. Do not stand on the product.
The Total Gym®is not intended for use by children.eep this and all fitness equipment out of the reach of
children.
Keep fingers, loose clothing, and hair away from moving parts.
Inspect your exerciser before each use to ensure proper operation.
Do not use this equipment unless all moving
parts, including cables and pulleys are working properly. See pages 10 - 11 for details on Inspection, Maintenance
and Storage.
The exerciser should only be used on a mat or carpeted surface to prevent unexpected movement of the unit.
Use only the accessory items recommended by the manufacturer.
To avoid serious injury, care should be taken at all times when getting on and off this or any exercise equipment.
SAFETY INSTRUCTIONS AND WARNINGS -Please reference Produc Specifica ions diagram on page 3.
5. a. Release Spring-Loaded Pin (on left side rail) as shown.
b.Fold Vertical Column down towards the center of the unit.
c. Then insert Safety Hitch Pin at bottom of vertical column.
6. Slide the Glideboard towards the bottom of unit shown in Figure 6.
7. With caution, to avoid pinched fingers or hands, grab the top of the
Glideboard and slowly pull the unit up allowing the rollers to bring the
back of the unit towards the center. eep approximately 12” apart.
8. Continue to fold the exerciser together until it is completely folded
and roll the exerciser into a closet for storage.To store under a bed,
simply lower the exerciser to the floor and roll under the bed.
Do not store unit in upright position when folded.
TO EMOVE THE GLIDEBOA D
You can also remove the Glideboard if you need to fit the exerciser under a narrow
space (between 6” and 8”).
IMPO TANT: The Glideboard weighs approximately 15 lbs. Use caution when
lifting it off of the exerciser. Lifting incorrectly may result in user injury.
1. With exerciser laying flat on the floor, disconnect the pulley
from the hook on the underside of the Glideboard.
2. Tilt up the Glideboard and slide it off the frame of the
exerciser.When the bench is completely off the
exerciser, set it aside.
3. Pull the Spring-Loaded Pin to release the Rail and fold the
exerciser together as shown above in Figure 7 & 8. Be sure
you release the Spring-Loaded Pin before folding.
Fig. 2
6.
12”
Back
Crossbar Front
Crossbar
Insert
Safety
Hitch Pin
Spring-
Loaded
Pin
Fig. 5b
Fold
Vertical
Column
down
Fig. 5a
Fig. 5c
Fig. 7 & 8
CRUSH HAZARD, KEEP HANDS CLEAR DURING FOLDING.
Lift Here
WARNING
WARNING
CAUTION

— 10 — — 3 —
PRODUCT SPECIFICATIONS
Handle
Glideboard
Bottom Outer Rail
Top Inner
Rail
Roller
Cable
Center Support Rail
Roller
Back Crossbar
Front
Crossbar
Leg Pulley Accessory Kit Multi Function Attachment
Vertical Height
Adjustment Column
Arm Pulley
Assembly
Spring-Loaded
Pin (located on
side of rail)
Height
Adjustment
“C” Pin
Rope
Pulley/D-Ring
Assembly
Clip
Foam
Pad
2 Large
Hitch
Pins
Brackets
1 Large
Hitch Pin
Clip
Foot
Harness
LENGTH: folded 50-1/2”
in use 88”
HEIGHT: folded 8-1/2”
in use 44”
WIDTH: 16-1/8”
WEIGHT: 58 lbs.
MAX. USER WEIGHT: 275 lbs.
Leg Pulley
Bracket
For use with
leg pulley
accessory only.
Allen
Wrenches
Packed in the leg pulley
accessory kit
Stopper
Height
Adjustment
Lever
Safety
Hitch Pin
WARNING
LABEL 3
WARNING
LABEL 1
WARNING
LABEL 2
WARNING
LABEL 4
CAUTION
LABEL 1
CAUTION
LABEL 2
WARNING
LABEL 3
WARNING
LABEL 5
INSPECTION, MAINTENANCE & STORAGE
INSPECT YOU TOTAL GYM®1100 P IO TO EACH USE
Before using your Total Gym®1100 for your workout session, be sure to make the
following inspection:
• Make sure the equipment is fully opened and sitting on a solid, level surface with plenty of
clearance on all sides. Unit should be used on a mat or on carpeted surfaces only.
• Make sure all the Hitch Pins are securely in place and locked into position.
• Check that the Pulley is attached securely to the loop on the top underside of
the Glideboard.
• Check that the Cables are traveling correctly in the groove of each pulley.
• Make sure the Cable is securely fastened to each Hand Grip.
• Check that the Multi Function Attachment or other accessories are installed
correctly when in use.
• Make sure the Glideboard is gliding smoothly along the frame.
OUTINE MAINTENANCE
•Wipe down your Total Gym®1100 on a regular basis using a clean cloth and alcohol or
alcohol-based products like Windex®or 409®. Do not leave towels or workout clothing
laying or hanging on the equipment.
• Periodically check the following parts for signs of fraying or other wear: the cable, pulleys,
wheels, glideboard, accessories and frame. If the cable, pulleys, frame or wheels need
replaced – do not use your unit, wait until the part is replaced. If any other part than the
ones listed above needs to be replaced, do not use that part until it is replaced.
• Never use a lubricant such as WD-40®or ArmorAll®to lubricate or clean the unit. Use only
3-in-1®oil or machine oil to lubricate the axles of the wheel or pulley, not the roller surface.
TO STO E YOU TOTAL GYM®1100
Follow these easy steps to store your exerciser properly:
1. Remove all accessories and attachments.
2. Remove Safety Hitch Pin and Safety Pin from Vertical Column.
3. Be sure the Cable Pulley is attached to the underside of the glideboard for folding.
4. Position one foot on Back Crossbar to keep the product from lifting off the floor. With one hand
on the rail, grasp the Height Adjustment “C” Pin and pull it out from the Height Adjustment
Column. Slowly lower the rails until they rest on the Back Crossbar.
5. Lower the Height Adjustment Column all the way down until it rests on the center rail.

— 9 —
SET UP
Your product comes with:
• Safety Hitch Pin located at the bottom of the Vertical Column, which must be removed prior to unfolding.
• One (1) Spring-Loaded Pin locked into the base of the left rail by the height adjustment tube. Left side is determined
by standing behind the unit facing the Vertical Column.
IMPO TANT: To Prevent Injury – Be sure the Spring-Loaded Pin is locked securely into place in the left
rail before using unit.This will prevent the Height Adjustment Column from falling forward.
• One Large Hitch Pin for Leg Pulley Bracket is located in the Leg Pulley Accessory it as well as two Large Hitch Pins
for the Multi Function Attachment.
IMPO TANT: Before using the Multi Function Attachment or Leg Pulley Accessory be sure the Hitch Pins are
securely inserted (see page 6 - 8 of this manual for directions).
1. Pull the product out of the shipping box. Remove all packaging
materials, including tape and cardboard inserts, from your unit.
2. Lay product on the floor with glideboard side up. Make sure you have
plenty of space on both ends of the product. Slide the glideboard as far
as it will go towards the Front Crossbar before you begin lifting unit.
3. Lift the exerciser up by holding it at the top of the rails. Using your foot,
slowly spread the unit open at the bottom approximately 12 inches so
that it rests firmly on the Front and Back Crossbars not allowing it to
go too far.
4. Make sure the handles are out to the sides before
you begin to unfold your unit. eep hands and fingers
away from pulley. Hold onto the top center of glideboard
and begin rolling rear rollers. Spread the unit out until it
is flat on the floor. Be careful to do this slowly.Be sure
to support the frame in the center to avoid having
the product drop suddenly onto the floor or pinch
fingers.
5. (a) Remove Safety Hitch Pin from bottom of Vertical Column.
Remove plastic packing ties from the top and bottom of the
Vertical Column. Pull out the Spring-Loaded Pin nob located
at the left rail (NOTE - pin shown in picture is on right side)
to release Spring-Loaded Pin. Continue to hold pin out while
performing the next step.
— 4 —
3.
12”
5a.
4.
Back
Crossbar
Front
Crossbar
Safety
Hitch Pin
Spring
Loaded
Pin
Lift Here
Hold Here While Lowering
To The Ground
STARTING OUT
Wear athletic shoes and comfortable light clothing when exercising on the Total Gym®1100. Do
not exercise barefoot. Check your exerciser before using to ensure that all the parts are in place
and working properly (see page 10 - 11 for details on Inspection, Maintenance and Storage).
Adult supervision is required at all times.
NOTE: Th Rails and Glid board can b rais d to any d sir d l v l on th H ight
Adjustm nt Column d p nding upon your d gr of fitn ss. Pl as not ,
how v r, that th Rails cannot b rais d to th high st position on th H ight
Adjustm nt Column wh n th L g Pull y Brack t is attach d to th column.
B sur you hav pl nty of fr spac around th x rcis r so that p rforming
on th Total Gym®1100, as w ll as g tting on and off, is conv ni nt and saf .
Each time you raise or lower the Adjustment Column, be sure you hold it to keep it
from dropping to the floor.
Begin using the product at a low incline. As your fitness level progresses, increase the incline to
increase the intensity and improve your muscle strength. Don’t be in a hurry to exercise at a high
intensity level; start out easily and build gradually. The Total Gym®1100 is as easy as 1-2-3
to use, so read on.
1. Important Things to emember When Using the Total Gym®1100
• Always have control of the glideboard before getting on and off the exerciser.
• eep your feet on the floor when getting on and off the exerciser. Only remove
them from the floor for the duration of the exercise.
• If you are using the handles, hold onto them as you get on and off the glideboard.
2. Exercising with the Handles Only
Grasp the handles which are attached to the cable and slide the glideboard to a position
in which you can comfortably sit or lay down when performing the desired exercise (see
Exercise Booklet). Be sure to keep your feet on the floor until you are in the correct
position for the specific exercise.Then, if the exercise calls for your feet to be off the floor,
place your feet as specified in the instructions.
3. Exercising with the Multi Function Attachment Only
Slide the glideboard to a position in which you can comfortably sit or lay down on when
performing the desired exercise (see your Exercise Booklet). eep your feet on the ground
until you are in the correct position and feel comfortable.Then, place your feet in the proper
position and begin to exercise.
When starting your exercise program, begin with the basic exercises shown in the Exercise
Booklet included with your Total Gym®1100 to familiarize yourself with the movements. Use the
lowest incline level to start with– you can work up to a higher incline level in the weeks and
months to come.
For the specific Total Gym®1100 exercises and programs, study and follow the
instructions in the Exercise Booklet included with your product.

— 8 —
(b) Take hold of the Vertical Column and pull it up until it is upright.
Release the Spring-Loaded Pin.You should hear it lock back into place.
IMPO TANT: Be sure the Spring-Loaded Pin is locked
into place before using your unit. You will know the pin
is locked into place when you can see the end protrude
through the inside of the rail bracket.
6. (a) Position one foot on Back Crossbar to keep the product from lifting
off the floor. With one hand on either the right or left rail and the other
hand holding the Height Adjustment “C”Pin, slide the rails up along
the Height Adjustment Column.Line up the hole to the first (lowest)
position on the Height Adjustment Column.
(b) Insert Height Adjustment “C” Pin
from the back as shown.
7. Push the pin down into its locked position (it should lay flat against
the Height Adjustment Column). Never sit on or exercise on the unit
without the Height Adjustment “C” Pin securely locked into place.
NOTE: Ins rt Saf ty Hitch Pin in th sid hol locat d
at th bottom of th V rtical Column.
(This is th pin you r mov d in st p 5a).
8. If the Stopper at the bottom of the Vertical Column has not
already been installed, please do so now. Locate the Stopper
which is packed in the Leg Pulley it (See Product Specifications
on page 3 of this manual). Unscrew nut on the end of the
Stopper and remove. Insert the Stopper into the hole located in
the center of the Back Crossbar. (See Fig. 1) Screw the nut back
onto the Stopper and tighten with Allen Wrenches provided.
(See Fig. 2)
IMPORTANT: Proper installation of the Stopper is necessary for
the Rollers to function easily when the unit is folded and rolled
into place for storage.
— 5 —
Fig. 1
Fig. 2
8.
STOPPE ASSEMBLY
6b.
5b.
6a.
7.
HOW TO ATTACH THE LEG PULLEY ACCESSORY KIT
1. Connect the Leg Pulley Bracket to the top of the Vertical Column by
aligning Bracket with the hole at the top of the column. (Be sure
bracket is right side up.) Insert Large Hitch Pin through the hole to
secure Bracket onto the Vertical Column (See Fig. 1).
2. Detach the Cable Assembly from the loop on the underside of the
glideboard and attach one of the Clips from the Leg Pulley Assembly.
3. Place D-Ring on Pulley first.Then connect the D-Ring to the Bracket
as shown. (See Fig. 2)
NOTE: If rop app ars to b twist d, tak D-Ring off and turn
Pull y around.
4.Attach the Foot Harness to one of your feet by placing your foot in
the Harness so the sewn-in-ring is on the bottom of your foot.
Pull tightly on the belt so the Harness is secure.(See Fig. 3)
5.(a) Position yourself on the glideboard correctly for the specific
exercise you want to perform.
(b) While lying down on the glideboard, connect the Clip on
the end of the rope to an O-Ring on the Harness attached
to your foot. (See Fig 4.) Depending on the exercise you are
performing, connect the Clip to the proper O-Ring. Be sure to
always stabilize the glideboard when clipping the Harness on
or off. Also, use caution when getting on or off the glideboard.
You are now ready to exercise using the Leg Pulley Accessory.
See your Exercise Guide for specific exercises that utilize the
Leg Pulley Accessory.
NOTE: emove Leg Pulley Bracket when you are not
exercising with it.
(c) To disconnect the Harness, unclip the rope from the O-Ring
on the Harness. Be sure to stabilize glideboard when
disconnecting Foot Harness.
TOP VIEW
Left Foot
Right Foot
TOP VIEW
Left Foot
Right Foot
TOP VIEW
Left Foot
Right Foot
Foot Harness
Harness
Buckle
O-Ring (loose)
O-Ring (sewn in)
O-Ring (loose)
Fig. 3
Fig. 4
Leg Pulley Accessory Kit
Rope Pulley/D-Ring
Assembly
Clip
Large
Hi ch
Pin
Clip
Harness
Leg Pulley Bracke
For use wi h leg pulley
accessory only.
Fig. 1
Fig. 2
Bracket
Bracket
D-Ring
Large Hitch Pin
Pulley
Pulley
Release
Spring-
Loaded Pin
Pull Vertical
Column Up
Clip

— 7 —
— 6 —
HOW TO ATTACH THE MULTI FUNCTION ATTACHMENT
The Multi Function Attachment provided with your unit has been uniquely designed to serve several
purposes. It can be placed at the top or bottom of the exerciser and angled toward you or away from
you depending upon what is comfortable for you.
Two thick Foam Pads are provided with the Multi Function Attachment. They must be attached to
the attachment (if not already) before exercising. To do this:
1. Simply wet each end of the straight crossbar of the
attachment with some soapy water.
2. Attach Foam Pads on the crossbar as shown
in Figure 1. Let dry before beginning to exercise
with the Multi Function Attachment.
Proper ways to use the Multi Function Attachment in accordance
with the exercises you wish to do:
PULL UPS
1. Locate the holes at the top of the right and left rails on the column
end of the unit.
2. With the attachment angled toward the glideboard, line up the
brackets on the attachment with the desired position holes on
the rails.
3. Insert the 2 Large Hitch Pins through the holes on the
Multi Function Attachment brackets and the hole on the
rails, as shown in Figure 2.
4. You are now ready to perform Pull Up and Chin Up exercises
to work the arms, lats and back. See your Exercise Booklet for
specific exercises.
LEG PULL: C UNCHES, LEGS AND SIT UPS
1. Locate the holes at the top of the right and left rails on the column
end of the unit.
2. With the attachment angled away from the glideboard, line
up the brackets on the attachment with the desired position
holes on the rails.
3. Insert the 2 Large Hitch Pins through the holes on the
Multi Function Attachment brackets and the hole on the
rails, as shown in Figure 3.
4. You are now ready to perform Leg Pulls, Crunches and Sit Up
exercises to work the abdominals, waist and legs. See your
Exercise Booklet for specific exercises.
Fig. 2
Fig. 1
Fig. 3
F ONT P ESS
1. Locate the holes at the bottom of the right and left rails near the
Front Crossbar.
2. With the attachment toward the glideboard, line up the brackets
on the attachment with the desired position holes on the rails.
3. Insert the 2 Large Hitch Pins through the holes on the attachment
brackets and the hole on the rails, as shown in Figure 4.
4. You are now ready to perform the Front Press which works the
upper chest and triceps. See your Exercise Booklet for specific
exercises.
SQUATS
1. Locate the holes at the bottom of the right and left rails near the
Front Crossbar.
2. With the attachment angled away from the glideboard, line up the
brackets on the attachment with the desired position holes
on the rails.
3. Insert the 2 Large Hitch Pins through the holes on the attachment
brackets and the hole on the rails, as shown in Figure 5.
4. You are now ready to perform the Front Press which works the
thighs and calves. See your Exercise Booklet for specific exercises.
NOTE: When performing the Squat exercises, be sure to position
your hands on the side of the glideboard, NOT along the
bottom of the board in order to avoid pinched fingers.
Fig. 5
Fig. 4