Totally Wicked Curve 2 Mini User manual

USER MANUAL / BEDIENUNGSANLEITUNG

2 3
Congratulations on purchasing your new
Totally Wicked Curve 2 Mini Electronic Cigarette.
The Totally Wicked Curve 2 Mini brings you a small, discreet easy
to use device. Comfortable to hold with outstanding variable
power performance. The highlight is the LED display showing
power settings in volts or watts, battery charge level, ohms
resistance and puff duration. The voltage is adjustable from 3.3V
to 5.0V and the wattage is adjustable from 5W to 20W according
to your vaping needs.
Curve 2 Mini Battery
1. LED display
2. Power button
3. “Up” button
4. “Down” button
5. Charging port
6. Double thread adaptor
CS Micro Tank
7. Atomizer base
8. CS atomizer head
(1.5 ohm)
9. Tank
10. Mouthpiece
1
2
7
9
10
3
4
6
8
5

4 5
Wir gratulieren Ihnen zum Kauf der
Totally Wicked Curve 2 Mini E-Zigarette.
Die Curve 2 Mini ist ein kleines, unaufdringliches und handliches
Dampfgerät, das leicht zu bedienen ist und Ihnen eine
ausgezeichnete Performance bietet. Das Highlight ist das
LED Display, welches den Akkuladestand, den Widerstand
des Verdampfers, die Zugdauer und die eingestellten Volt/Watt
Parameter anzeigt. Die Spannung kann individuell von 3.3V bis
5.0V und die Leistung zwischen 5W und 20W eingestellt werden.
Curve 2 Mini
1. LED Display
2. Power-Taster
3. “Rauf” Taster
4. “Runter” Taster
5. Ladebuchse
6. eGo-Adapter mit
Doppelgewinde
CS Micro Tank
7. Verdampferbasis
8. CS Verdampferkopf
(1.5 Ohm)
9. Tank
10. Mundstück
1
2
7
9
10
3
4
6
8
5

6 7
Using your Curve 2 Mini
Power on and off: Press the power button
5 times in quick succession; the LED display
will light and show the percentage of battery
power remaining, the Curve 2 Mini is now on
and ready to use. The display will turn off after
10 seconds of inactivity, but will seamlessly
recover when any button is pressed. To turn
the Curve 2 Mini off, press the power button 5
times in quick succession.
To fill the tank: Remove the complete CS
Micro Tank from the Curve 2 Mini battery by
unscrewing at the atomizer base. Invert the
tank, unscrew and remove the atomizer base.
Refill the tank through one of the apertures
either side of the central air tube. Do not place
liquid in the central tube. Refit the atomizer
base and screw the assembled tank back onto
the Curve Mini battery.

8 9
Using your Curve 2 Mini
Vaping:
Press the power button as you inhale. When the button is held down the LED display will display
vaping time in seconds for a period of 2 seconds, the display will then show battery power
remaining as a percentage for a further 2 seconds.
Vaping Time Remaining Battery

10 11
Using your Curve 2 Mini
Watts: Cycle through the selections until the
“W” flashes and then press the power button
to select wattage mode.
In selection mode you can see the remaining
power, ohms resistance of the atomizer in use
and the power mode you selected by pressing
the “up” or “down” buttons.
Changing output between
volts and watts:
Press the power button 3 times to go into the
power selection mode. Press either the “up” or
“down” buttons to cycle through options.
Volts: Cycle through the selections until the
“V” flashes and then press the power button to
select voltage mode.

12 13
Using your Curve 2 Mini
Adjusting output level:
Output from the battery can be adjusted
by pressing the “up” or “down” buttons
momentarily whilst the Curve 2 Mini battery is
switched on. The LED display will show the
volts or watts as selected.
Charging the battery:
Remaining battery charge is indicated on the LED display as a
percentage of remaining power, and the battery charge indicator will flash
several times when remaining charge is 10% or below. The battery can
be recharged using the supplied USB cable. Connect the large USB plug
into a dedicated USB port or wall adaptor, and connect the micro USB
plug into the USB port on the base of the Curve 2 Mini. When connected,
the LED will display “USB” for 2 seconds and then change to show the
level of charge for 10 seconds. The “%” will flash while the battery is
charging, and will go out when the battery is fully charged. The Curve 2
Mini can be used normally during battery charging.
V/W DOWN V/W UP

14 15
Malfunction Indication and Protection Atomizer Head Replacement
Over 10 Second Protection: When the power button is pressed for over 10 seconds, the output
will shut off. Normal operation will resume after the power button is released.
Atomizer Short-circuit Protection/Resistance Low: If an atomizer short-circuit occurs or the
atomizer resistance is too low, the LED display will show “Lo Ω”.
Low-voltage Protection: When the voltage of the battery is below 3.0V, the Curve 2 Mini battery
will shut down and will require charging.
Remove the complete CS Micro Tank from
the Curve 2 Mini battery by unscrewing at the
atomizer base. Invert the Tank, unscrew and
remove the atomizer base. Unscrew the CS
atomizer head from the atomizer base and
replace. Refit the atomizer base and screw
the assembled tank back onto the Curve 2
Mini battery.

16 17
Bedienung Curve 2 Mini
Power-Taster Ein/Aus: Taster 5-mal
hintereinander drücken; das LED Display
leuchtet auf und signalisiert, dass die Curve
2 Mini an und zur Nutzung bereit ist. Zum
Ausschalten Taster ebenfalls 5-mal drücken.
Im aktiven Modus geht das Display nach ca.
10 Sekunden aus und leuchtet erneut auf,
wenn ein beliebiger Taster gedrückt wird.
Tank befüllen: CS Micro Tank an der
Verdampferbasis haltend von der Curve 2
Mini abschrauben. Tank umdrehen und die
Verdampferbasis abschrauben. E-Liquid an
der Tankwand, um die Luftführung herum,
einfüllen. E-Liquid darf nicht in die mittlere
Luftführung gelangen. Verdampferbasis
samt Verdampferkopf wieder an den Tank
schrauben.

18 19
Bedienung Curve 2 Mini
Dampfen:
Power-Taster drücken und inhalieren. Nach dem Drücken zeigt das LED Display für ca. 2 Sekunden
die Dampfdauer und danach den Akkuladestand in Prozent an.
Zugdauer Akkuladestand