Toto EGO TX721AE User manual

SPECIFICATIONS
S06210Z
INSTALLATION
1 2
2. NUT
3 4
Pen
Bracket
Drill
Water Supply
Screw
Bracket
Cover
Elbow
Water Supply
6
TROUBLESHOOTING
Hand
Shower
Flexible
Hose
TX 721AEZ
"EGO" Sliding Rail (L= 625mm)
TX 721AEV3
"EGO" Sliding Rail w/ Elbow, Flexible
Hose &Hand Shower
"EGO" SLIDING RAIL (L=625mm) TX721AE
Packing
Ø24
69
18
30
Ø42
50
Ø6
67
Sleeve
Anchor
Ø6 Holes
3. NUT
Ø24
69
Ø6
18
30
50
Ø42
67
Packing
Screw
Body
Pipe
5
Hanger
Flow Regulator Inside
(Don t remove)
R15
CHECK
POINT
Unsatisfactory spray 1 Clean
Water leaks around the hose 2 , 3 Tighten
PROBLEM
SOLUTION
1. NOZZLES
OPERATING CONDITIONS
MAINTENANCE
Always wipe chrome plated area with dry soft cloth,
and sometimes wipe it with cloth soaked in mild soap.
ATTENTION
1. Water supply pressure : 0.05 ~ 0.75 MPa.
2. Ensure that water supply is clean ( No Sand, Dirt, Etc.).
Use Seal Tape
(Not Include)
Don t use abrasive cleaning material such as; detergents
containing hydrochloric acids, thinner, polishing powder,
and nylon brush.
Flow regulator should not be remove because it could
damage the system
As the product model is constantly updated, the actual
product may not look the same as it shown in the diagram,
but the basic installation principles are the same.
1.
2.
3.

SPESIFIKASI
S06210Z
PEMASANGAN
1 2
2. NUT
3 4
Pen
Bracket
Drill
Water Supply
Screw
Bracket
Cover
Elbow
Water Supply
6
Hand
Shower
Flexible
Hose
TX 721AEZ
"EGO" Sliding Rail (L= 625mm)
TX 721AEV3
"EGO" Sliding Rail w/ Elbow, Flexible
Hose &Hand Shower
"EGO" SLIDING RAIL (L=625mm) TX721AE
Packing
Ø24
69
18
30
Ø42
50
Ø6
67
Sleeve
Anchor
Ø6 Holes
3. NUT
Ø24
69
Ø6
18
30
50
Ø42
67
Packing
Screw
Body
Pipe
5
Hanger
Flow Regulator Inside
(Don t remove)
R15
1. NOZZLES
Use Seal Tape
(Not Include)
PENYELESAIAN MASALAH
Pancaran tidak memuaskan 1 Bersihkan
Air bocor disekitar selang 2 , 3 Kencangkan
MASALAH
SOLUSI
POIN
PERIKSA
KONDISI OPERASIONAL
PEMELIHARAAN
Selalu bersihkan area yang berlapis krom dengan
kain lembut kering, dan sesekali bersihkan dengan
kain yang direndam dalam sabun yang dicampur air.
PERHATIAN
Jangan gunakan bahan pembersih yang bersifat abrasif
seperti deterjen yang mengandung asam klorida, tinner,
bubuk polishing dan sikat nilon.
Flow regulator tidak boleh dilepas karena dapat merusak
sistem
Karena model produk terus mengalami pembaharuan,
aktual produk mungkin tidak sama dengan gambar, tapi
prinsip dasar pemasangan adalah sama.
1.
2.
3.
1. Tekanan sumber air: 0.05 ~ 0.7.5 MPa.
2. Pastikan kondisi sumber air adalah bersih
(tidak ada pasir, kotoran dan lain lain)