Toto TTSH302J Installation instructions

1
2
3 4
Ø6
35 .
(850)
( =500 .)
200
( )
!
(2. )
(11.
)
(14. )
(17. )
(13.
)
(15. )
(16. )
(1. )
(3. )
(4. )
(5. )
(6. )
(7. )
(8. )
~
~
(12.
)
10, 17
9, 11, 12, 13, 17
1, 2, 3, 4, 5, 6, 7, 8
14, 15, 16
(10. )
(9. )
0-2026-3561

Component parts
Shower column unit 1 et
Elbow pipe 1 pc
Fixed hower head (Scare) 1 pc
Wall holder + fixing crew 1 et
Inlet ho e (L= 500 ) 1 pc
Shower ho e (L= 1500) 1 pc
Hand hower 1 pc
Diverter valve 1 et
Product Drawing
Installation and owner manual
To u e the product effectively. Should follow the in truction of thi manual.
Cuations be ore installation
1. Hot and cold water pre ure during u e.
Minimum pre ure...................................0.05 MPa (flow pre ure)
Maximum pre ure..................................0.75 MPa (High pre ure)
2. The hot water temperature hould not exceed 65°C. It' recommended in the range of 60±5°C, hot water do not u e tream
3. The ambient temperature hould above 0°C, if not higher than 0°C, product will be deformed, cracked and other damaged.
4. To prevent internal damage of hower, the water temperature of di charge ide hould not exceed 60°C. It' recommended
below 45°C.
5. Inca e haven't u ed for long time. It may be lead to internal and external corro ion.
Installation Procedure
Figure 1
Figure 2
Ø6
Hole Depth 35 mm
Anchor
Holder Self-tapping crew
(850)
Holder
Fa tening nut
Taper wa her
Retaining wall block
Elbow pipe
Fixed
hower
head
Hand hower
Shower ho e
Shower hanger
Diverter valve
Holder
Faucet
Water out
connector
Water in
connection
Lever
Water out
fitting
Inlet ho e
(L=500mm)
Warning!
To prevent being calded due to malfunction, make ure that the diverter valve i witched to the hand hower po ition in order to
te t the water temperature before u ing. Cannot allow the diverter valve witched underneath over head hower.
Care and Cleaning
Troubleshooting
Check Item
After in tallation, if there i malfunction occuring, plea e ee below.
Un table election valve
Vibration
Water leak
Problem
Le flow rate
Fa tening nut
(1. Have enough tight)
(3. Have enough tight)
(4. Have enough tight)
(7. Have enough tight)
Holder
(2. Have enough tight)
Screw
Hex crew
(5. Have enough tight)
Fa tening nut
(6. Have enough tight)
Holder
Screw
(8. Have enough tight)
Hex crew
Your new product i de igned for year of trouble-free performance.
1. Keep it looking new by cleaning it periodically with mild oap, rin ing thoroughly with warm water and drying with a clean, oft cloth.
2. Do not u e abra ive cleaner , teel wool or har h chemical , a the e will damage the product.
3. Do not u e liquid cleaner with acid-ba e content. Inca e of accidentally happening, rin e with pure water immediately in order to
prevent any damage of product urface.
Failure to follow the e in truction may void your warranty.
Warranty
Plea e find detail in warranty card a attached
Adju ting nut
200mm lift
Hand hower po ition
Fixed hower po ition
Figure 3 Figure 4
~
~
O-Ring
(11. Scratched)
Ga ket rubber
(13. Scratched)
(14. Have enough tight)
Pre ure pool
(15. Have enough tight)
(16. Have enough tight)
Lever handle
Fa tening crew
Packing
(17. Scratched, dirt)
O-ring
(12. Scratched)
10, 17
9, 11, 12, 13, 17
1, 2, 3, 4, 5, 6, 7, 8
14, 15, 16
Flow Regulator
(10.Dirt)
Packing
(9. Scratched, dirt)
1. Installation wall mouting
2. Installation ixed shower head
3. Installation hand shower
4. Trial or tightening con irmatiom
5. Diverter Valve
Require adju t the height of the fixed hower
by adju ting the nut.
0-2026-3561