Toto TX423MEB User manual

SPECIFICATIONS
OPERATING CONDITIONS
S060482
MAINTENANCE
TROUBLESHOOTING
EBHAND SHOWER SET W/ SINK TAP TX423MEB
Watersupply pressure : 0.05 ~ 0.75 MPa.
Ensure that water supply is clean( No Sand,Dirt, Etc.).
1.
2.
Always wipe chrome plated area with dry soft cloth, and
sometimes wipeit with cloth soaked in mild soap.
1
2
CHECK
POINT
Unsatisfactoryspray 1 Clean
Water leaks around the hose 2, 3 Tighten
Water leaks around the handle 4, 5 Tighten
Handle is loose 6, 7 Tighten
PROBLEM
SOLUTION
INSTALLATION
2 X Ø5.5
Holes
Tap Water
Supply
3. NUT
2. NUT
6. BOLT
4. CERAMIC
HEAD WORK
5. CERAMIC
HEAD WORK
7. BOLT
Hanger
Sleeve
Anchor
Screw
Packing
Packing
HandShower
Flexible Hose
ATTENTION
3
Flow Regulator Inside
(Don t remove)
Use Seal Tape
(Not Include)
1. NOZZLES
G½
28
20
56°
Ø38
45
20°
107.5
30
74
Ø5.5
Don t use abrasive cleaning material suchas; detergents
containing hydrochloric acids, thinner,polishingpowder, and
nylonbrush.
FlowRegulator should not be remove because it could damage
the system.
As the product model is constantly updated, the actual product
maynot look the same as it shown in the diagram, but the basic
installation principles are the same.
1.
2.
3.

SPESIFIKASI
KONDISI OPERASIONAL
PEMELIHARAAN
PENYELESAIAN MASALAH
EBHAND SHOWER SET W/ SINK TAP TX423MEB
Tekanansumber air: 0.05~ 0.75 MPa.
Pastikan kondisi sumber air adalah bersih(tidak ada pasir,
kotoran dan lain lain)
1.
2.
1
2
CHECK
POINT
Pancaran tidak memuaskan 1 Bersihkan
Air bocor di sekitar selang 2, 3 Kencangkan
Air bocor disekitar handle 4, 5 Kencangkan
Handle longgar 6, 7 Kencangkan
PROBLEM
SOLUTION
PEMASANGAN
2 X Ø5.5
Lubang
Tap
Sumberair
3. NUT
2. NUT
6. BOLT
4. CERAMIC
HEAD WORK
5. CERAMIC
HEAD WORK
7. BOLT
Hanger
Sleeve
Anchor
Screw
Packing
Packing
HandShower
Flexible Hose
PERHATIAN
3
Flow Regulator di dalam
(Jangan dilepas)
Gunakan Seal Tape
(Tidak termasuk)
1. NOZZLES
G½
28
20
56°
Ø38
45
20°
107.5
30
74
Ø5.5
Jangan gunakan bahanpembersih yang bersifat abrasif seperti
deterjen yang mengandung asam klorida, tinner, bubukpolishing
dan sikat nilon.
FlowRegulator tidak boleh dilepas karena dapat merusak sistem.
Karena model produk terus mengalami pembaharuan, aktual
produk mungkin tidak samadengan gambar, tapi prinsip dasar
pemasangan adalah sama.
1.
2.
Selalu bersihkan area berlapis krom dengan kain lembut kering, dan
sesekali bersihkan dengan kain yang direndam dalam sabun yang
dicampur air.
3.
S060482