Town & Country Fireplaces D Series User manual

WARNING: If the information in these
instructions is not followed exactly, a re or
explosion may result causing property damage,
personal injury or death.
FOR YOUR SAFETY
Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch.
• Do not use any phone in your building.
• Immediately call your gas supplier from a
neighbour’s phone. Follow the gas
supplier’s instructions.
• If you cannot reach your gas supplier call the
fire department.
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
This appliance may be installed in an aftermarket
permanently located, manufactured home (USA
only) or mobile home, where not prohibited by local
codes.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is not
convertible for use with other gases, unless a
certified kit is used.
This appliance is suitable for installation in a
bedroom or bed sitting room.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
Visit www.townandcountryfireplaces.com for the most recent version of this manual
TCWS.54STOK
Indoor/outdoor Fireplace
Installation Manual.
270619-56 TCWS54.STOK 100001140-50
This is a decorative product
and is not intended to be
used as a heating appliance.
INSTALLATION MANUAL
MODEL: TCWS.54STOK
SERIES D
DIRECT VENTED
DECORATIVE GAS
SEE THRU APPLIANCE
POWER VENTED ONLY

Table of Contents
100001140 2TCWS54STOK_270619-56
We recommend that our gas hearth products
be installed and serviced by professionals who
are certied in the United States by the National
Fireplace Institute® (NFI) as NFI Gas Specialists
HOT GLASS WILL CAUSE
BURNS.
DO NOT TOUCH GLASS UNTIL
COOLED.
NEVER ALLOW CHILDREN TO
TOUCH GLASS.
!
DANGER
A barrier designed to reduce the risk of burns from the
hot viewing glass is provided with the appliance and
shall be installed for the protection of children and
other at-risk individuals.
WARNING: This product
can expose you to chemicals
including ceramic bers,
which are known to the State
of California to cause cancer, and carbon
monoxide, which is known to the State of
California to cause birth defects or other
reproductive harm.
For more information go to
www.P65Warnings.ca.gov.
This warning is applicable to all
Pacific Energy Fireplace Products
R - Value Statement .................................................................. 3
Caution ...................................................................................... 3
Safety ........................................................................................ 3
Important Note for the Commonwealth of Massachusetts ....... 4
Fireplace Dimensions ................................................................ 5
Minimum Clearances to Combustible Material ......................... 6
Installation Requirements .......................................................... 7
Manufactured (Mobile) Home .................................................... 7
Door Frame Removal ................................................................ 7
Standoffs ................................................................................... 8
Locating The Fireplace .............................................................. 8
Framing and Finishing ............................................................... 9
Building envelope sealing procedure ...................................... 10
Double sided tape for exterior side vapour barrier .......... 11
Building materials - Outer trim prole view ............................. 12
Non-combustible board detail ......................................... 14
Non-combustible recessed installation detail.................. 14
Calcium silicate board...................................................... 14
Secure steel frame to combustible framing ..................... 15
Adjustable Lintel ...................................................................... 15
Lintel Adjustment ............................................................. 16
Power Venting Options ............................................................ 17
Electrical .................................................................................. 18
Installation ........................................................................ 18
Wall Switch and Remote Control ............................................ 19
Linking the remote control unit to the wall switch............ 19
Selecting Natural Vent and Power Vent Modes ....................... 19
Home Automation ................................................................... 20
Home automation cable length ....................................... 20
Gas Supply .............................................................................. 21
Venting - Wall Power Vent Kit Only .......................................... 22
Venting Congurations ............................................................ 23
Minimum Vent Length Chart .................................................... 24
Vent Terminal Minimum Clearances ........................................ 24
Venting Components ............................................................... 25
Vent Pipe Sealant .................................................................... 26
Optional Tranquility Burner ...................................................... 27
Contents of Package:....................................................... 27
Installation: ....................................................................... 28
Propane Conversion ................................................................ 33
Optional Twilight Diamond Burner ........................................... 35
Contents of Package:....................................................... 35
Installation: ....................................................................... 36
Installation (Indoor side only) ........................................... 39
Finishing Touch Trim Kit Installation ........................................ 39
Wiring instructions for the TC54ST Twilight Burner kit ............ 41
Gas Pressure Check ................................................................ 43
Correct gas pressure requirement:................................... 43
Burner Flame Adjustment ........................................................ 44
Firebox Panels Installation ...................................................... 45
Lighting Instructions ................................................................ 46
Maintenance ............................................................................ 47
Glass Panel: ..................................................................... 47
Annual Inspection:............................................................ 47
Periodically:...................................................................... 47
Replacement parts-TCWS.54STOK ........................................ 48
Replacement Parts - TCWS.54DST ........................................ 49
Replacement Parts - Tranquility Burner .................................. 50
Replacement Parts - Twilight Diamond Burner ....................... 51
Replacement Parts – Valve Control System ............................ 52
Wiring Diagram ........................................................................ 53
Rating Label ............................................................................ 54

100001140
FOR YOUR SAFETY - Do not install or operate your Town & Country replace without rst reading and understanding
this manual. Any installation or operational deviation from the following instructions voids the Town & Country Fireplaces
Warranty and may prove hazardous.
This appliance and its individual shut off valve must be disconnected from gas supply piping system during any pressure
testing of that system at test pressures in excess of 1/2 psig (3.5 kPa).
This appliance must be isolated from the gas supply piping system by closing its individual manual shut off valve during
any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (3.5 kPa).
Note: When lit for the rst time, the appliance will emit a slight odour for a couple of hours. This is due to the curing of
paints, sealants and lubricants used in the manufacturing process. This condition is temporary. Open doors and windows
to ventilate area. Smoke and fumes caused by the curing process may cause discomfort to some individuals.
Do not use the replace if any part has been under water. Immediately call a qualied service technician to inspect the
replace and to replace any part of the control system and any gas control which has been under water.
Due to high temperatures, this gas appliance should be located out of trafc and away from furniture and draperies.
Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns
or clothing ignition.
Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young
children, and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are
at-risk individuals in the house. To restrict access to a replace or stove, install an adjustable safety gate to keep
toddlers, young children, and other at-risk individuals out of the room and away from hot surfaces.
Clothing or other ammable material should not be placed on or near the appliance.
Any grill, panel or door removed for servicing the unit must be replaced prior to operating. Failure to do so may create a
hazardous condition.
Installation and repair should be done by a qualied service person. The appliance should be inspected before use and
at least annually by a professional service person. More frequent cleaning may be required due to excessive lint from
carpeting, bedding material, etc. It is imperative that control compartments, burners and circulating air passageways of
the appliance be kept clean.
It is our policy that no responsibility is assumed by the Company or by any of its employees or representatives for any
damages caused by an inoperable, inadequate, or unsafe condition which is the result, either directly or indirectly, of any
improper operation or installation procedures.
This appliance must not be connected to a chimney ue serving a separate solid fuel burning appliance.
It has been determined that the Town and Country model TCWS.54STOK indoor/outdoor Fireplace has an R value of 5.8.
This determination has been arrived at by the calculation of the typical R value of two layers of 5mm Ceramic glass,
combined with 17 inches of ventilated air gap. The one layer of 5mm tempered glass has been ignored in the calculation
due to it being open to the exterior air environment on both sides. Real world results may vary due to environmental
factors.
3
TCWS54STOK_270619-56
Caution
Safety
R - Value Statement

100001140
Important Note for the Commonwealth of Massachusetts
From Massachusetts Rules and Regulations 248 CMR 5.08:
(a) For all side wall horizontally vented gas fuelled equipment installed in every dwelling, building or structure used in whole or in part for residential
purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet
above nished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall be satised.
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fuelled equipment, the
installing plumber or gas tter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the oor
level where the gas equipment is to be installed, in addition, the installing plumber or gas tter shall observe that a battery operated or hard-wired
carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal
vented gas fuelled equipment. It shall be the responsibility of the property owner to secure the services of qualied licensed professionals for the
installation of hard-wired carbon monoxide detectors.
a. In the event that the side wall horizontally vented gas fuelled equipment is installed in a crawl space or an attic, the hard-wired carbon monoxide
detector with alarm and battery back-up may be installed on the next adjacent oor level.
b. In the event that the requirements of this subdivision cannot be met at the time of completion of installation, the owner shall have a period of thirty
(30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide
detector with an alarm shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions shall
comply with NFPA 720 and be ANSI/UL 2034 listed as IAS certied.
3. SIGNAGE. A metal or plastic identication plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet
above grade directly in line with the exhaust vent terminal for the horizontally vented gas fuelled heating appliance or equipment. The sign shall
read, in print size no less than one-half (1/2) inch in size, “GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.
4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fuelled equipment shall not approve the installation unless,
upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.089(2)
(a) 1 through 4.
(b) EXEMPTIONS. The following equipment is exempt from 248 CMR 5.089(2)(a) 1 through 4.
1. The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54 as adopted by the
Board; and
2. Product Approved side wall horizontal vented gas fuelled equipment installed in a room or structure separate from the dwelling, building or structure
used in whole or in part for residential purposes.
(c) MANUFACTURER REQUIREMENTS – GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product Approved side wall
horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions provided
by the manufacturer for installation of the equipment and the venting system shall include:
1. Detailed instructions for the installation of the venting system design or the venting system components; and
2. A complete parts list for the venting system design or venting system.
(d) MANUFACTURER REQUIREMENTS – GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a Product Approved
side wall horizontally vented gas fuelled equipment does not provide the parts for venting the fuel gases, but identies “special venting systems”, the
following requirements shall be satised by the manufacturer.
1. The referenced “special venting system” instructions shall be included with the appliance or equipment installation instructions; and
2. The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed
installation instructions.
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fuelled equipment, all venting instructions, all parts
lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.
4TCWS54STOK_270619-56

74 3/4"
54 1/16"
3 3/16" 1/2"
54 1/16"
74 3/4"
Front view
Top view
Prole view
Figure 1: TCWS54STOK Dimensions.
variable
adjustment
(See page 15)
100001140
5
TCWS54STOK_270619-56
Fireplace Dimensions

29 3/4"
24"
4“
*
CEILING
ADJACENT WALL
OR MANTEL SUPPORT
6 ”
COMBUSTIBLE FLOOR
COMBUSTIBLE HEARTH
Figure 3: TCWS54STOK Minimum mantel clearances.
100001140
UNIT MAY BE RECESSED UP TO 4 1/2” WITH
NONCOMBUSTIBLE MASONRY TYPE MATERIAL
Minimum Clearances:
Side standoffs ....................................................... 0 in. (0 mm)
Back standoffs ...................................................... 0 in. (0 mm)
Top standoffs......................................................... 0 in. (0 mm)
Bottom of appliance.............................................. 0 in. (0 mm)
Adjacent side wall ................................................. 4 in. (102 mm)
Ceiling to appliance............................................. 24 in. (610 mm)
*Mantel to appliance...............................See Figure #2
**Maximum Mantel extension.................See Figure #2
Mantel support ...................................................... 4 in. (102 mm)
Vent pipe ...................................................... 1 3/4" in. (45 mm)
* MANTEL CLEARANCE
A 9”
B 6”
C 3”
** MANTEL DEPTH
D 12”
E 6 3/4”
F 1 1/2”
MANTEL CLEARANCE
CHART
MAY USE COMBUSTIBLE
FACING MATERIAL IN THIS AREA
NON-COMBUSTIBLE
FINISH MATERIAL
SEE FIG #11& 12
NON-COMBUSTIBLE ZONE.
DO NOT INSTALL ANY COMBUSTIBLE MATERIAL,
ELECTRICAL WIRING OR GAS PLUMBING IN THIS
AREA.
COMBUSTIBLE FRAMING AND
FINISH WALL ABOVE STANDOFFS
STEEL FRAMING
FIREPLACE FRONT
TOP OF LINTEL BAR
A
B
C
D
E
F
Figure 2: TCWS54STOK Mantel clearances.
6TCWS54STOK_270619-56
Minimum Clearances to Combustible Material

Figure 6: Handle.
Figure 4: Safety barrier screen.
HANDLE
SAFETY BARRIER
SCREEN
The Town & Country Fireplace installation and venting must conform to the current CAN/CGA-B149 installation code (in
Canada) or the current National Fuel Gas Code, ANSI Z223.1 (in the USA), and approved per local codes. Only qualified
(licensed or trained) personnel should install this product.
In the state of Massachusetts, only a licensed Plumber and Gas Fitter may install this product.
In some jurisdictions, the Town & Country Fireplace may be installed in Manufactured Homes after the "rst sale". Consult local codes
for approval. The replace must be fastened in place.
Install in accordance with the current standard Mobile Homes, CAN/CSA Z240 MH (in CANADA), and the Manufacturer's Home
Construction and Safety Standard, Title 24 CFR, Part 3280 or the current Standard for Fire Safety Criteria for Manufactured Home
Installations, Sites and Communities ANSI/NFPA 501A (in the USA).
Installation Requirements
Manufactured (Mobile) Home
Door Frame Removal
Warning: Turn off the fireplace, and allow ample time for the unit to cool before proceeding.
Caution: The ceramic glass is very fragile, and should be handled with care.
The door frame is held in place by two spring-loaded latches that are operated by a one-piece latch handle.
1. Remove safety barrier screen (Figure 4) by prying the top portion of the screen toward you, then lift the screen from its tabs
(inset) located at the base of the door frame.
2. Remove the TC Finishing Touch Trim Kit from the door frame. (If installed)
3. Using a screwdriver (Figure 5) or other similar object, push against the notch in the top of the latch and grab the bottom of the
latch handle as it protrudes (Figure 6). Lift handle until latch hook disengages. Repeat for other side while holding glass so it does
not tip out.
4. Tilt the top of the door frame out to clear the top edge of the unit. Grasp the sides of the frame and lift up and out to disengage
from its bottom track.
5. Place the door frame in a safe place to avoid damage.
6. Re-assemble in reverse order. Latch handle should snap into place and be ush with door frame when engaged correctly.
7. Reinstall Trim Kit if required.
8. Reinstall safety barrier screen.
TIP:
To ensure glass is properly latched, grasp the top left and right sides of the glass
frame, under moderate pressure it should pull forward and return to original position
evenly on both sides.
Figure 5: Accessing handle.
100001140
7
TCWS54STOK_270619-56

Figure 7: TCWS54STOK Frame as standoffs.
Figure 8:
TCWS54STOK
Possible locations.
100001140
The framing kit, once assembled and attached, are used as the top and side standoffs.
In planning the installation for the replace, it is necessary to determine where the unit is to be installed, location of vent
system and where gas supply piping may be plumbed. Various types of installations are possible, such as, a peninsula
wall, an island, and between two interior walls (Figure 9). Due to high temperatures, do not locate this replace in areas
of high trafc or near furniture or draperies.
The minimum clearances from the replace to combustible surfaces must be adhered to and are shown in Figure 2 and Figure 3.
EXAMPLES OF COMMON
LOCATIONS SEE SEE FIGURE 1 FOR
DIMENSIONS
8TCWS54STOK_270619-56
Locating The Fireplace
Standoffs

Figure 8:
TCWS54STOK
Possible locations.
100001140
Note: The fireplace should be in place
and venting installed before framing
in or building an enclosure around the
unit.
When the appliance is installed directly on
carpeting, tile or other combustible
material, other than wood ooring, the
appliance shall be installed on a metal or
wood panel extending the full width and
depth of the appliance.
The Town & Country replace must be
framed in as described below or totally
enclosed with non-combustible material,
such as facing brick.
Determine the total thickness of facing
material to be used. A thickness of 3/4"
will allow the nishing surface to be ush
with the front of the unit. If preferred,
additional masonry type non-combustible
material can be installed above and to the
sides up to 4 1/2 inches forward of the
appliance.
*The finishing material must not inter-
fere with glass frame access.*
A Steel Stud Framing Kit is supplied with
the replace and must be used unless
the replace is totally enclosed with
non-combustible material. The framing
kit comes fully assembled and the
outdoor section of the replace come fully
insulated.
The sides and top of the replace are
framed in up to the steel studs using
conventional lumber. Consult local build-
ing codes for specic requirements.
Due to high temperatures, non-combusti-
ble backer board, such as cement board
or its equivalent, must be used to sheet in
the front of the replace, extending to the
top of the metal frame and laterally to the
framing edge bars (Figure 15). Standard
sheet rock (dry wall) may be used beyond
this.
If the backer board is not to be nished
with other non-combustible material
such as tiles, it is recommended that top
sections of the board be a single sheet of
calcium silicate board or its equivalent.
Taped and mudded joints may crack due
to the elevated temperatures.
Chase Insulation:
When installing this replace against a
non-insulated exterior wall or chase, it
is recommended that the outer walls
be insulated to same degree as other
exterior walls. Do not place replace
directly against the insulation. Cover the
insulation and plastic vapour barrier with
a solid surface, such as dry wall (sheet
rock). Consult local codes. Do not insulate
or use plastic vapour barrier within the
framing kit.
CAUTION: See “Figure 17” on page
14 before proceeding.
NOTE:
The chase must be
properly sealed at the
ceiling level or between
floors in a multilevel
installation.
Outer Trim
Outdoor side Glass assembly
Inner Trim
TCWS54STOK Fireplace
(pre-assembled)
Figure 9: Outdoor side components and their order of assembly.
9
TCWS54STOK_270619-56
Framing and Finishing

100001140
Any type of siding may be used (minimum 120 F rating). See Figure 12
Note: Local building codes and regulations
may vary. Consult local building
codes prior to installation.
Building envelope sealing procedure
Stainless steel ashing
1/2" OSB board
(factory installed)
Outer door trim
Wall
Exterior wall
sheathing Seal joint with ashing tape
prior to applying house wrap
barrier lm (not supplied)
Use supplied double
sided tape to adhere
house wrap barrier
lm to stainless steel
ashing
Figure 10: Building envelope sealing.
10 TCWS54STOK_270619-56

100001140
Exterior side Interior side
Double sided
tape to ax
vapour barrier
to the inside
of the exterior
side wall
Exterior side
Vapour barrier
Interior side
Figure 11: Tape for exterior wall vapour barrier.
Double sided tape for exterior side vapour barrier
A strip of double sided tape is pre-applied to the inside portion of the exterior wall. This allows
the installer to extend the application of vapour barrier so that the entire exterior wall is protected
from moisture.
11
TCWS54STOK_270619-56

100001140
Building materials - Outer trim profile view
Siding material - Must
not interfere with outer
door trim removal. Fireplace outer
wall assembly.
Outer door trim..
1 1/2 inch air space
required from the
bottom of the door
trim for ventilation.
(Facing material or siding
above and/or below the 1 1/2
inch air space, may extend
outwards from the replace as
far as desired as long as the
1 1/2 inch air space is maintained).
door frame.
Dashed line indicates
space between removable
window frame and siding
or facing material needed
to allow for removal of
outer door trim
Siding or facing material may
make contact with the door
frame on the top and sides of
the door frame but not with
the bottom of the door
frame. There must be a
minimum 1 1/2 inch space
between the bottom of the
door frame and the siding
to allow for ventilation.
Siding or facing material must
not make contact with the
removable outer window trim.
There must be enough space
between the siding or facing
material and the removable
outer window trim to allow for
removal of door trim.
Location of double side
tape for vapour barrier.
Figure 12: Outdoor-side building materials.
12 TCWS54STOK_270619-56

74 3/4"
54 1/16"
Figure 14: Outside door dimensions.
100001140
Double sided tape is factory installed over stainless steel anges.
Peel backing from double sided tape
prior to applying house wrap barrier lm.
Double sided tape pre-applied to outdoor box to keep vapour barrier lm rmly in place.
Figure 13: Double sided tape for outdoor box.
13
TCWS54STOK_270619-56

Figure 15: Non combustible board within frame.
54 1/16"
74 3/4"
20 5/16"
20 13/16" - 23 13/16"
Figure 18: Frame kit dimensions.
100001140
Non-combustible board detail
Calcium silicate board
NON-COMBUSTIBLE
BOARD
If nishing the wall above the unit with
paint, the framing kit shipped with
the unit should be discarded. Use full
sheets of calcium silicate board or
equivalent and full length metal studs to
nish and frame around the unit.
Calcium silicate board is a high grade
material with cement, quartz and natural
minerals as the main raw materials.
(Note: Calcium Silicate is 1/2” thick)
CAUTION: Calcium Silicate board
can be damaged if dropped or struck.
Handle with care. Inspect board prior to
installation and do not use if cracked.
NOTE: It is recommended to pre-drill
mounting holes in the board prior
to securing to the framing. This will
prevent the board from cracking.
Figure 17: Non-combustible board
location.
NON-COMBUSTIBLE
MATERIAL MUST EXTEND
TO THE TOP EDGE AND TO
THE SIDE EDGE OF THE
FRAMING KIT.
NON-COMBUSTIBLE
BOARD ONLY IN
THESE AREAS
NOTE: FIREPLACE SHOULD BE IN ITS FINAL LOCATION BEFORE FRAMING.
This replace may be recessed
up to a maximum depth of 4
1/2”. This recess must be con-
structed from non-combustible
material.
It is important to note that any
nishing material used must
not interfere with the glass
door being able to open in the
event of ignition of excess gas
buildup.
Figure 16: TCWS54STOK Recessed installation details.
Non-combustible recessed
installation detail
14 TCWS54STOK_270619-56

Adjustable Lintel
Figure 21: Framing edge location.
Figure 19: Bend tab out 90 degrees.
This replace may be recessed up
to a maximum depth of 4 1/2”, this
recess must be constructed from
non combustible material. The space
between the outside lintels and the
rebox must be completely free of
any obstructions or debris and the
door with trim tted must be able to
move freely. No building material is
permitted to protrude past the lintel
bars attached to the replace under
ANY circumstance.
Secure steel frame to combustible framing
•Bend out the tabs 90 degrees before inserting the unit into its framed housing (Figure 19).
•Secure the frame assembly to the wood frame through the tabs (Figure 20).
Install Non-Combustible Board (not supplied)
• Use drywall screws 8 to install the non-combustible board.
NON COMBUSTIBLE
FINISH MATERIAL
Figure 20: Attaching metal tab to frame.
Area inside Lintel must
remain free of obstructions
Non combustible building
material may not extend
past this point
100001140
15
TCWS54STOK_270619-56

Safety
barrier
screen
Glass
door
trim
Flanged
edge
Hemmed
edge
Figure 22: Lintel and trim.
Lintel securing bolt
Figure 23: Upper left securing bolt.
Lintel Adjustment
1. The adjustable lintel assembly
has two orientations for
desired nishing. The anged
edge and the hemmed edge
(Figure 22). The lintel comes
factory installed with the ange
edge out . If the desired edge
is different from the factory
setting, use the following
steps to change it.
2. Remove safety barrier screen.
3. Remove the door trim from the
door frame.
4. Loosen the securing bolts in
the upper and lower corners
on each side of the lintel
(Figure 23) and remove the
lintel. Rotate the assembly to
have the desired edge away
from the replace.
5. The lintel assembly can then
be adjusted to align ush with
your facing material by sliding
in or out approximately 1”.
6. Tighten the securing bolts .
7. Re-attach the door trim.
8. Reinstall safety barrier screen.
Lintel securing bolt
Figure 24: Lower right securing bolt.
100001140 16 TCWS54STOK_270619-56

Figure 25: Horizontal mount power vent. Figure 26: Vertical power vent.
Power Venting Options
POWER VENTING CONFIGURATIONS
A power vent is mandatory on this indoor/outdoor replace. This replace can be power vented either hori-
zontally or vertically.
• For Horizontal power venting where venting lengths between 3 feet to 110 feet are required, the power
vent unit TCVT.PV7.110 must be used. The internal fan speed in this power vent unit must be switched
to the HIGH setting.
• Where Vertical power venting is required, the power venting unit TCVT.PVCV must be used. Total vent-
ing length can be up to 110 feet but is restricted to a 66 foot maximum vertical rise. There is no internal fan
speed switch to be concerned with.
100001140
17
TCWS54STOK_270619-56

Note: Installation must be performed by a qualified installer, service agency or gas supplier.
Figure 28: Junction box wiring.
Firebox access panel
Figure 27: Firebox access panel.
The gas control system is located on the right hand side of the rebox behind an access panel and the decorative rebox
panel (if installed). The replace is operated via a wall control and a hand held remote control unit.
The wall control is connected to the replace by a 40 ft. communication cable
supplied with the replace.
Installation
1. Place the replace in the desired location.
2. Remove the glass door from the replace.
3. Remove access panel from bottom left hand side of the rebox (Figure 27).
4. Ensure that the switch on the IFC board is set to PV (Power Vent)
(Figure 29).
5. Connect 110 V. AC electrical supply to the wires installed inside the
junction box (Figure 27). The replace is rated at 110 volts, 60Hz, 0.25A.
The optional power vent kit is rated at 115 volts, 60Hz, 1.8A. The electrical
wires can be accessed from both inside and outside the junction box by
removing one of the two small access panels (Figure 28 and Figure 29).
6. Attach the wall switch to the framing in the desired location. (40 ft is
supplied with replace).
7. Route the wall switch control cable as required to the wall switch (Figure
31).
8. Attach one end of the wall switch control cable
to the interface board (Figure 29), and the other
end to the wall control (Figure 31).
9. Do not install batteries into the wall switch
(Figure 32). Battery holder must remain
empty.
10. If not already installed, install the burner using
the instructions supplied with the burner kit.
11. Turn on the gas supply and check that all
connections are tight and leak free.
12. Turn on gas and electrical supplies.
13. Move the center button on the wall control
(Figure 30) to the “ON” position. The igniter
will start to spark. After a short delay, the
pilot will light followed by the main burner.
JUNCTION BOX
Electrical
This entire length of the supplied cable MUST be used. DO NOT substitute
this cable with any other cable. Do not add on to the length of this cable. Wall
switch for the fireplace must be located in the same room as the fireplace.
Transformer
Vacuum
switch
Inside access
panel
Gas
connector
Wall switch
connector
Junction box
Module
Interface board
Power vent
switch
Regulator
board
Gas valve
Figure 29: Valve assembly components.
100001140 18 TCWS54STOK_270619-56

Note: Installation must be performed by a qualified installer, service agency or gas supplier.
Figure 31: Wall switch - interface side.
The TCWS54STOK_D must be pre-set
to the “PV” setting.
TO FIREPLACE
Wall Switch and Remote Control
Selecting Natural Vent and Power Vent Modes
Note: The wall switch for the TCWS54STOK must not have batteries installed in it. The batteries are for
back up in case of a power outage. This fireplace must not operate with a battery back up.
Figure 30: Town and Country
wall switch.
Linking the remote control
unit to the wall switch.
1. Begin by moving the selector
toggle on the wall switch to the
“REMOTE” position.
2. Insert a straightened paper clip
into the “PROGRAM” slot on the
wall switch.
3. Press the internal “PROGRAM”
button once and wait until you
hear 3 beeps from the wall switch.
4. Press the ON/OFF button of the
remote unit. Once the wall unit
beeps 3 times, the remote is
programmed.
5. The toggle on the wall switch
must be kept in the “REMOTE”
position in order to use the remote
control unit.
The NV/PV (Natural Vent / Power Vent) switch (Figure 33)
on the interface board (Figure 29) is set according to which
type of evacuating vent system is present. In all cases with
the TCWS54STOK replace, the NV/PV switch MUST be
set to PV.
Figure 32: Wall switch no batteries.
Figure 33: Vent mode selection switch.
DO NOT install batteries in
the wall switch
100001140
19
TCWS54STOK_270619-56

Figure 34: Complete communication wiring.
TO HOME
AUTOMATION
SYSTEM
The home automation feature supplied with this replace is capable
of controlling the ame and light on/off function with the use of a dry
contact relay common to home automation systems. Furthermore, the
ame and light level may be modulated from high to low using the
0 - 10 volt analog output available on most home automation systems.
Figure 35 shows the wire designations required to connect the replace
to a home automation system.
Home Automation
NOTE:
• Digital I/O must be connected to a dry contact relay.
• Analog ame and light input through 0 - 10 volt DC
signal scaled as follows:
Low = 1 volt
High = 10 volts
Figure 35: Home automation wiring.
Home automation cable length
The cable from the home automation system to the wall switch should be
a length of no more than 200 feet.
SUPPLIED CABLE
FROM FIREPLACE
100001140
NOTE:
When a signal has been supplied by the home automation system, the fireplace control
will repeat the signal every 2 hours or until a new command has been received.
Leave the wall switch on the “Remote” setting when using home automation.
20 TCWS54STOK_270619-56