Toyotomi TAN-A53EW User manual

SERVICE MANUAL
ROOM AIR CONDITIONER
TAN/TAG-A53EW
TAN/TAG-A70EW
CONTENTS
SPECIFICATION ....................................................................1
FUNCTIONS ..........................................................................5
SERVICE FUNCTION EXPLANATION ..................................7
OPERATION DETAILS...........................................................8
TROUBLESHOOTING GUIDE.............................................17
PERFORMANCE CURVE DIAGRAM ..................................25
SCHEMATIC DIAGRAM AND
THERMISTOR RESISTANCE CHART.................................
ELECTRIC CIRCUIT DIAGRAM ..........................................
EXPLODED VIEW (INDOOR UNIT) ....................................
EXPLODED VIEW (OUTDOOR UNIT) ................................
PARTS LIST (INDOOR UNIT)..............................................
PARTS LIST (OUTDOOR UNIT)..........................................

SPECIFICATION
– 1 –
TAN/TAG-A53EW
Unit
BTU/hCooling Capacity
INDOOR OUTDOOR
–
BTU/hHeating Capacity –20,500
L/h
phase
Moisture Removal –
Power source
Single
V230
Hz 50
OUTLET
Airflow Method
TOP VIEW
INTAKE
m/min
Air circulation (at High) Cooling ;
Heating ;
W
Electrical Data
Input
Running Current
Starting Current
Inner diameter
Length
Cooling ; –
–
Heating ;
ACooling ; –
–
Heating ;
A
inch
Piping Connection Port (Flare piping) L L
inch G G
inch
Pipe Size (Flare piping) inch
mm
Drain hose
Length
Height
Width
Depth
Number of core-wire
Power Cord
–
m–
m–
core-wire/ 2 mm –
mm
Dimensions mm
mm
kg
Net Weight
3
2
; Half Union 1/4''
; Half Union 1/2''
L (liquid side) ; 1/4''
G (gas side) ; 1/2''
; 2-way valve 1/4''
; 3-way valve 1/2''
L (liquid side) ; 1/4''
G (gas side) ; 1/2''
16,900
3.1
29.0
12.0
12.0
1,760
1,665
8.1
7.7
14
0.6
1.4
297
799
210
9.1
642
780
245
44
SIDE VIEW
TAG-A53EW
TAN-A53EW

SPECIFICATION
– 2 –
Unit
Air Circulation
INDOOR OUTDOOR
Cross-flow Fan Propeller Fan
30 38
DC brushless (8-pole) Induction (6-pole)
W
Heat Exchanger 21.2FPI 19.5 FPI
Capilary Tube
Plate fin configuration,forced draft
Refrigerant Control Device g (oz)
Refrigerant (R410 A)
–1,460(51.5)
–
OLR(INNER)
–
Thermostat
Protection Device
Air Filter
Parts Provided
Electronic Control
Type
Motor Type
Rated Output
–
Mold-proof –
Specifications are subject to change without notice.
1 Mounting plate
2 Remote controller
3 Battery (2 pcs.)
4 Remote controller holder
5 Screw cap (2 pcs.)
6 Drain elbow
Timer –
Real time dual ON/OFF
7-hour OFF
TAG-A53EW
TAN-A53EW

SPECIFICATION
– 3 –
TAN/TAG-A53EW
Unit
BTU/hCooling Capacity
INDOOR OUTDOOR
–
BTU/hHeating Capacity –24,500
L/h
phase
Moisture Removal –
Power source
Single
V230
Hz 50
OUTLET
Airflow Method
TOP VIEW
INTAKE
m/min
Air circulation (at High) Cooling ;
Heating ;
W
Electrical Data
Input
Running Current
Starting Current
Inner diameter
Length
Cooling ; –
–
Heating ;
ACooling ; –
–
Heating ;
A
inch
Piping Connection Port (Flare piping) L L
inch G G
inch
Pipe Size (Flare piping) inch
mm
Drain hose
Length
Height
Width
Depth
Number of core-wire
Power Cord
–
m–
m–1.4
core-wire/ 2 mm –
mm
Dimensions mm
mm
kg
Net Weight
3
2
; Half Union 1/4''
; Half Union 5/8''
L (liquid side) ; 1/4''
G (gas side) ; 5/8''
; 2-way valve 1/4''
; 3-way valve 5/8''
L (liquid side) ; 1/4''
G (gas side) ; 5/8''
22,000
4.4
54.0
14.0
15.0
2,290
2,240
10.1
9.9
14
0.6
295
799
210
9.1
643
850
330
59
SIDE VIEW
TAG-A70EW
TAN-A70EW

SPECIFICATION
– 4 –
Unit
Air Circulation
INDOOR OUTDOOR
Cross-flow Fan Propeller Fan
30 100
DC brushless (8-pole) Induction (6-pole)
W
Heat Exchanger 21.2FPI 18.1FPI
Capillary Tube
Plate fin configuration,forced draft
Refrigerant Control Device g (oz)
Refrigerant (R410A)
–1,700(60.0)
–
OLR(INNER)
–
Thermostat
Protection Device
Air Filter
Parts Provided
Electronic Control
Type
Motor Type
Rated Output
–
Mold-proof –
1 Mounting plate
2 Remote controller
3 Battery (2 pcs.)
4 Remote controller holder
5 Screw cap (2 pcs.)
6 Drain elbow
Timer –
Real time dual ON/OFF
7-hour OFF
Specifications are subject to change without notice.
TAG-A70EW
TAN-A70EW

– 5 –
REMOTE-CONTROL TRANSMITTER
ON/OFF
Operation mode selection
AUTOMATIC
COOL
DRY
HEAT
CIRCULATER
Air flow selection
AUTOMATIC
HIGH
MEDIUM
LOW
Room temperature setting
16°C〜30°C
Timer operation selection
CONTINUOUS operation
OFF
ON
Sleep
Timer / time setting
Operation stops at the set time(OFF timer)
Operation starts at the set time(ON timer)
0.5〜7.0hours(Sleep timer)
Air flow direction control
Auto angle selection
Auto swing mode
Manual mode
INDOOR UNIT
Sensing the room temperature
Room temperature sensor (thermistor)
Time delay safety control
Restarting is inhibited for approximately
3 minutes.
Indoor fan speed control
High, Med, Low
Operation indication lamps (LED)
(GREEN).......Light up in operation
(YELLOW) .... Timer in operation
(GREEN).......Outdoor unit operate
Dry operation mode
Intermittent operation of fan at low speed.
Room temperature control
Maintains the room temperature in
accordance with the setting temperature.
Deice (defrost) control
Deicing operation automatically starts
when the heating efficiency is declined by
the ice formed in the outdoor unit.
After deicing operation, heating operation
automatically starts with “Hot start
function.”
FUNCTIONS
SET
ON
APM
CLOCK
OFF
℃
LH
M
AUTO
MODE
FAN
TIMEADJ
ON OFF
LOUVER

– 6 –
Hot-start control (heating)
The indoor fan stops until the evaporator
piping temperature will be reached.
Overload protection
Anti-freezing control for the
evaporator
Compressor will be stopped when the
evapolator’s piping temperature is below
2°C for one minute.
Compressor will be restarted when the
evaporator’s piping temperature is above
2°C.
Airflow direction control
Automatic airflow direction control
The louver automatically swings up and
down (cooling, dry)...horizontal and 30°
downward.
The louver is set at 60°downward
during heating operation.
The louver is set as horizontal when the
fan is stopped.
Airflow direction manual control.
Can be set within a range at horizontal to
60°downward.
Auto recovery function
If there is any power failure during
operation, operation status before power
failure is memorized.
3〜4 minutes after power recovery, the
unit restarts automatically with previous
operation status memorized.
(3〜4 minutes is protective time for
compressor.)
Attention
Because of Auto Recovery Function, if
shutting off the power supply during
operation, the unit may restart
irrespective your intention when turning
on the power supply next time.
If the unit is not to be used for a long
time, shut off the power supply after
terminating all operation with remote
controller.
OUTDOOR UNIT
Compressor overload protector
When overheating of the compressor is
detected, inner protector stops the
operation of the compressor.
When high current supplied to the
compressor is detected, the main
controller stops the operaiton of outdoor
unit including compressor
3 min. forced operation control
Once the compressor is activated, it does
not stop for 3 minutes.
In case of termination of this operation,
push the ON/OFF button on remote
controller.
FUNCTIONS

– 7 –
EMERGENCY AND TEST OPERATION
Emergency Operation
•Use this operation only when the remote controller is out of order or lost.
•When the emergency operation switch is pressed, the “Pi” sound starts once,
which means the start of this operation.
•In this operation, the system automatically selects the operation modes, cooling
(or heating when available) according to the room temperature, as follows.
・It is not possible to operate in dry mode.
Test Operation
Test operation switch is same as emergency one.
•Use this operation only for testing the performance of the machine in the condition
where the room temperature is less than 16°C.
•Continue to press the test operation switch for more than 5 seconds.
After you hear the “Pi” sound twice, release your finger from the switch: the
cooling operation starts with the air flow speed “HI.”
•If the test operation switch is pressed more than 10 seconds, it doesn’t work.
•After 30 minutes, test operation ends automatically.
SERVICE FUNCTION EXPLANATION
Pi
Pi...Pi Pi
<Remote control unit> <Indoor unit>
Receive
Ex-factory setting (Mode A) Ex-factory setting (Mode A)
Cut R10 on the PC board (Mode B)
Have "J1"on the PC
board short-circuited
by soldering (Mode B)
Receive
Not receive
Not receive
ON
APM
CLOCK
OFF
℃
LH
M
AUTO
℃
ON
APM
CLOCK
OFF
℃
LH
M
AUTO
℃
J1
Soldering
J1
Temperature
ABOVE 23℃
BELOW 23℃
COOLING
HEATING
26℃
23℃
CONTINUOUS
CONTINUOUS
AUTOMATIC
AUTOMATIC
Operation
mode Designated temperature Timer mode Air flow
HOW TO RELEASE EMERGENCY AND TEST OPERATION
•In case of releasing during those operations, you can either push emergency operation switch once more or
apply operation using remote control.
You will hear a beep sound and emergency/ test operation is released.
•If you release the operation by remote control, operation will continue as setting of the remote control
automatically.
INTERFERENCE PREVENTION OF SIGNALS FROM THE REMOTE CONTROLLER
When two indoor units used in the same room, interference of the signals may happen. To avoid this, alternative
signal model B can be selected by the following. (Ex-factory setting is mode A)
•Remote controller side : Have “J1” on the PC board short-circuited by soldering.
•Indoor unit side : Cut “R10” on the PC board.
(Each Operations Details)

– 8 –
OPERATION DETAILS
TIMER OPERATION
ON Timer operation
•Press the ON/OFF switch.
•Set the “ON Time” : Press the “TIMEADJ” button twice.
Adjust the time with the “ , ” button.
Press the “TIME ADJ” button twice.The setting of “ONTime” is complete and the present time appears on the LCD.
•Set the “ON Timer” : Press the Timer fixing button “ON”.
OFF Timer operation
•Press the ON/OFF switch.
•Set the “OFF Time” : Press the “TIMEADJ” button 3 times.
Adjust the time with the “ , ” button.
Press the “TIMEADJ” button once.The setting of “OFF Time” is complete and the present time appears on the LCD.
• Set the “OFF Timer” : Press the Timer fixing button “OFF”.
Sleep Timer operation
• Press the “SLEEP” button during the operation.
• Set the operating period by pressing the “SLEEP” button until the period appears on the LCD.
Timer Cancellation
•ON/OFF Timer : Press the Timer fixing button “ON”(On Timer) and/or “OFF”(Off Timer) once again.
•Sleep Timer : Press the “SLEEP” button until the operating period on the LCD disappears.
Level
Approx.10 degrees
(Cooling/Dry)

Approx.70 degrees
(Heating)

Standard Position
Approx.10
degrees
Approx.40
degrees
Approx.45
degrees Approx.70
degrees
Level
Swing of Air Flow
Cooling
Dry Heating
AIRFLOW DIRECTION CONTROL
Vertical adjustment
When ON/OFF switch is pressed, the vertical louver will move to the adequate positions for each operation
automatically.
Swing of air flow
If air flow direction switch is pressed once, the vertical louver will move within the range of figures.
Fixing the flow direction
If air flow direction switch is pressed again, the vertical louver will be fixed and that position is memorized.
From the next operation the louver will be set at previous position automatically.
Notes :
• In Swing Mode, the louver automatically moves up and down within the certain range, as the illustration below.
• There is two different ranges of louver swinging; one is of cooling & dry mode operation and the other is of
heating operation.

– 9 –
COOLING MODE OPERATION
•Compressor stops when the room temperature is cooled down to the designated temperature.
•Compressor restarts when room temperature is raised to +0.7°C higher than the designated temperature.
OPERATION DETAILS
ROOM TEMP.
DESIGNATED TEMP.
INDOOR FAN ON
ON OFF ON ON ON ON
OFF
COMPRESSOR
0.7
OFF OFF
TIME DELAY SAFETY CONTROL FUNCTION - FOR PROTECTION OF COMPRESSOR
•Compressor will not restart, in any operation modes, for 3 minutes after its stop.
• Compressor does not stop during the first 3 minutes of its operation even if the room temperature reaches to
the designated temperature, except changing setting temperature.
•Fan speed control when “Auto” is selected in fan mode
When “Auto” is selected,the fan speed is automatically controlled according to the difference between the room
and designated temperatures.
ROOM TEMP.
DESIGNATED TEMP.
Hi Me
Lo Hi
INDOOR FAN
＋3℃(＋2.7℃)
＋1℃(＋1.3℃)
＋3.7℃(＋3.3℃
)
＋1.7℃(＋2.0℃
)
＋0.7℃
Me