TP-Link Omada FC111PB-20 User manual

Scenario 1: Connect Devices with Optical Interfaces
LC-SC Fiber Cable
Ethernet Device
with Optical Interfaces
Media Converter
Fast Ethernet
100BASE-X (Fiber) Interface IP Camera AP
Powered Device (PD)
10/100Mbps WDM Media Converter with 1-Port PoE
Enlarge Your Ethernet Network
©2023 TP-Link 7106510662 REV2.20.0
LED Explanation
On: Power on
O:
Power o
PWR
PoE
On: Valid link
Flashing: Transmitting or receiving data
O: Invalid link
Link/Act
Package Contents: Converter, Power Adapter, Installation Guide
On: Supplying power normally
O: Supplying power abnormally or no power supply
PWR PoE
Twisted-Pair Cable
Note:
• The maximum output power of FC111PB-20 is 15.4W. PoE devices that require more than 15.4W are not supported.
• The PoE Media Converter supplies steady power and data connectivity to a powered device such as PoE IP Camera and PoE AP.

EU declaration of conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU,
2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.
The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce.
General Specifications Environmental and Physical Specifications
Specications
0˚C to 50˚C (32˚F to 122˚F)
-40˚C to 70˚C (-40˚F to 158˚F)
5% to 90% RH non-condensing
10% to 90% RH non-condensing
Operating Temperature
Storage Temperature
Storage Humidity
Operating Humidity
IEEE 802.3, IEEE 802.3i, IEEE802.3u, IEEE802.3afStandards
1 SC ber optic; 1 RJ45 jackConnector
Twisted-Pair
10BASE-T: 2-pair UTP/STP of Cat. 3 or above (≤100 m)
100BASE-TX: 2-pair UTP/STP of Cat. 5 or above (≤100 m)
100BASE-BX10: SMF
802.3af; up to 15.4 W for the PoE port
PoE
48 V/0.375 A
Power
1310 nm TX, 1550 nm RX
Wavelength
Dimensions 94.5*73*27 mm
Fiber 9/125 μm single-mode ber
Transmission Distance ≤20 km
For technical support and other information, please visit
https://www.tp-link.com/support, or simply scan the QR code.
To ask questions, find answers, and communicate with TP-Link users or
engineers, please visit https://community.tp-link.com to join TP-Link
Community.
PWR, Link/Act, PoELED
Scenario 2: Connect Devices without Optical Interfaces
SC-SC Fiber CableTwisted-Pair Cable Twisted-Pair Cable
Ethernet Device
without Optical Interfaces
Media Converter
10/100M
Fast Ethernet
Fast Ethernet PWR PoE
Media Converter
10/100M
PWR
IP Camera AP
Powered Device (PD)
UK declaration of conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Electromagnetic
Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations 2016.
The original UK declaration of conformity may be found at https://www.tp-link.com/support/ukca/
CAN ICES-3 (A)/NMB-3(A)
Industry Canada Statement
FCC compliance information statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference
that may cause undesired operation.
Any changes or modications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
Product Name: 10/100Mbps WDM Media Converter with 1-Port PoE
Model Number: FC111PB-20
Responsible party:
TP-Link USA Corporation
Address: 10 Mauchly, Irvine, CA 92618
Website: https://www.tp-link.com/us/
Tel: [phone]
Fax: [phone]
E-mail: [email protected]
We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with
the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and
the equipment is properly maintained and operated.
Issue Date: 2023/12/26
This is a class A product. In a domestic environment, this product may cause radio interference, in which case the
user may be required to take adequate measures.
CE Mark Warning
E
xplana�on of the symbols on the product label
S
ymbols may vary from products. The label is at the bottom of the product.
Symbol
Explanation
Class II equipment
Class II equipment with functional earthing
Alternating current
Direct current
Pola rity of d.c. power connector
For indoor use only
Dangerous voltage
Caution, risk ofelectric shock
Ene rgy eciency Marking
Protective earth
Earth
Frame or chassis
Functional earthing
Caution, hot surface
Caution
Operator's manual
Stand-by
"ON"/"OFF" (push-push)
Fuse
Fuse is used in neutral N
Cauti on, avoid listening a t high volume levels for long periods
Disconnection, a llpower plugs
m Switch of mini-gap construction
µ
Switch of micro- gap construction (for US version)
Switch of micro-gap /micro - disconnection construction
(for other versions except US)
ε Switch without contact gap (Semiconductor switching device)
RECYCLING
This product bears the selective sorting symbol for Waste
electrical and electronic equipment (WEEE). This means that
this product must be handled pursuant to European directive
2012/19/EU in order to be recycled or dismantled to minimize its
impact on the environment.
User has the choice to give his product to a competent recycling
organization or to the retailer when he buys a new electrical or
electronic equipment.
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних
документів та вимогам, що передбачені чинними законодавчими актами України.
Safety Information
Keep the device away from water, re, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
Do not use damaged charger or USB cable to charge the device.
Do not use any other chargers than those recommended.
Adapter shall be installed near the equipment and shall be easily accessible.
Do not point or stare directly into the beam or into the optical port of the transceiver when it is operating, as this can injure your eyesight
Use only power supplies which are provided by manufacturer and in the original packing of this product. If you have any questions, please don't
hesitate to contact us.
Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due
to improper use of the device. Please use this product with care and operate at your own risk.