TP-Link TD-8610 User manual

COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered
trademark of TP-LINK Technologies Co., Ltd. Other brands and product names are
trademarks or registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to
make any derivative such as translation, transformation, or adaptation without permission
from TP-LINK Technologies Co., Ltd. Copyright © 2006 TP-LINK Technologies Co., Ltd.
All rights reserved.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
EC DECLARATION OF CONFORMITY (EUROPE)
In compliance with the EMC Directive 89/336/EEC, Low Voltage Directive 73/23/EEC, this
product meets the requirements of the following standards:
• EN55022
• EN55024
• EN60950
SAFETY NOTICES
Caution: Do not use this product near water, for example, in a wet basement or near a
swimming pool.
Avoid using this product during an electrical storm. There may be a remote risk
of electric shock from lightning.

Package contents.............................................................................................................. 1
Chapter 1: Product Overview............................................................................................ 2
1.1 Product main specification................................................................................... 2
1.2 Supporting protocol.............................................................................................. 2
1.3 Transmit data-rate................................................................................................ 3
1.4 ATM property........................................................................................................ 3
1.5 System support.................................................................................................... 3
1.6 Working environment........................................................................................... 3
1.7 Electric parameter................................................................................................ 3
Chapter 2: Hardware Installation Guide............................................................................ 4
2.1 System requirement............................................................................................. 4
2.2 LED explanation................................................................................................... 4
2.3 Rear-panel........................................................................................................... 4
2.4 Hardware installation procedures（figure2-1）................................................... 5
Chapter 3: How to use ...................................................................................................... 6
3.1 Computer Configuration....................................................................................... 6
3.2 Login.................................................................................................................... 7
3.3 Setup ................................................................................................................... 8
3.4 Software Dial........................................................................................................ 9
Appendix A: Default Config............................................................................................. 10
Appendix B: Contact Information......................................................................................11

TD-8610 External ADSL MODEM User Guide
Package contents
The following contents should be found in your box:
 One TD-8610 ExternalADSL MODEM
 One AC power Adapter for TD-8610 ExternalADSL MODEM
 One Resource CD for TD-8610 ExternalADSL MODEM, including:
•This Guide
•Other Helpful Information
 One RJ45 cable
 Two RJ11 cable
 One ADSL splitter
Note: If any of the listed cable are damaged or missing, please contact the retailer from
whom you purchased the TD-8610 ExternalADSL MODEM for assistance.
- 1 -

TD-8610 External ADSL MODEM User Guide
Chapter 1: Product Overview
TP-LINK® TD-8610 External ADSL MODEM is the latest product designed and
manufactured by TP-LINK Technologies Co., Ltd. With TP-LINK’s excellent design of
circuit and high quality production, we guarantee ADSL MODEM a high performance,
very good stability and easy to use.
TD-8610 uses integrated ADSL2+ transceiver and a 256-MHz MIPS32 CPU.The AFE
supports full-rate ADSL connectivity conforming to the ITU and ANSI specifications;
MIPS32 CPU with MMU and 16-KB I-cache/8-KB D-cache is integrated into the device.
In addition to the basic DMT physical layer functions, the ADSL PHY supports dual latency
ADSL Framing (fast and interleaved) and the I.432 ATM Physical Layer.
TD-8610 is a complete plug-and-play solution. With standard Ethernet interface, it can
be directly connected to any 10M/100M Ethernet devices,support Auto-MDIX.
TD-8610 not only use html (web mode through Ethernet port) to configure the MODEM
but also use external utility software，too. You can download it from our website
(http://www.tp-link.com).
1.1 Product main specification
 High speed and asymmetry data transmit mode, adapt to wide-band internet access
 Point to point connection, provide safe and exclusive bandwidth
 Support All ADSL industrial standards
 Advanced DMT modulation and demodulation
 Firmware upgradeable
 Compatible with all mainstream DSLAM (CO)
 Real-time Configuration and device monitoring
 Quick response semi-conductive surge protect circuit, provides reliable ESD and
surge-protect function
1.2 Supporting protocol
- G.992.1 (G.dmt) - Annex A/B/C
- G.992.2 (G.lite) - Annex A/B/C
- ANSI T1.413
- G.992.3 (ADSL2) - Annex A/B/C/M and Annex L (RE-DSL) compliant
- G.992.5 (ADSL2+) Annex A/B/C and Annex L (RE-DSL) compliant
- ADSL dual latency (fast path and interleaved path)
- I.432 ATM physical layer compliant
- 2 -

TD-8610 External ADSL MODEM User Guide
-Supports RFC2516 (PPPoE) *
- Supports RFC1483 (EoA)( Bridged)
NOTE. “*”Need third-party software.
1.3 Transmit data-rate
 Max download data-rate: 24Mbps
 Max upload data-rate: 1Mbps
 Max line length: 6Km
1.4 ATM property
 AAL0, AAL5, OAM, RM, and raw cell types supported
 Direct hardware support for 4 Receive VCs, with additional RX VCs and TX VCs
supported in software
 Full 24-bit Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI)
1.5 System support
 Support PVC
 Support IEEE 802.3、IEEE 802.3u
 Support 10Base-T/100BASE-TX full-duplex or half duplex Ethernet
 Support Auto-MDIX
1.6 Working environment
 Operating temperature: 0℃~40 ℃
 Storage temperature: -40℃~70 ℃
 Humidity: 10%～90%
1.7 Electric parameter
 Adaptor power Output: 9VAC/0.8mA，50Hz or 60 Hz
 Power consumption: 4W Maximum
- 3 -

TD-8610 External ADSL MODEM User Guide
Chapter 2: Hardware Installation Guide
2.1 System requirement
Confirm your computer has been installed with networking interface card (NIC) before
connecting ADSL MODEM to your computer, with operating system supporting the
TCP/IP protocol.
2.2 LED explanation
The panel of ADSL MODEM includes one power button, one power indicator (RED) and
four function indicators (GREEN), and these five indicators are explained as chart 1-1:
Indicator Description Status Function Details
PWR Power On
Off Power OK Power fail
ADSL ADSL status
Slow flash
Quick flash
On
Self-detecting when power up
Connecting to the telecom network
Connection to telecom network OK
ALARM Mistake On
Off
There is mistake when ADSL transmitting
data or receiving data
ADSL normal
ACT Data
On
Off
There is data transmitting or receiving on
WAN port
No data transmitting or receiving on WAN
port
LAN Ethernet
On
Off
Flash
LAN port normal
Connection on LAN port abnormal
Data transmitting or receiving on LAN port
Chart 1-1
2.3 Rear-panel
 ON/OFF: Turn on/off the ADSL MODEM’s power.
 Power (9VAC/0.8A input): please do not use any unknown power adaptor,
otherwise that may damage your ADSL MODEM.
 RESET(reset default): First press push the reset button of MODEM, then turn on
the MODEM’s power about three minuters. It will utilize the default manufacturer’s
setting.
 LAN: Connect with your computer’s NIC.
 LINE(WAN): Connect to the MODEM of Splitter or Connecting the telephone line.
- 4 -

TD-8610 External ADSL MODEM User Guide
2.4 Hardware installation procedures（figure2-1）
First Step: Connecting the MODEM of Splitter with the LINE port of the TD-8610 ADSL
MODEM by telephone line. While you need to use a telephone, please attach telephone
line into the phone of Splitter.
Second Step: Connect category 5 cable with RJ45 jacks toADSL MODEM’s LAN port
and your computer’s NIC.
Third Step: Link power adapter into the power jack of ADSL MODEM. Please note the
range of voltage of power adapter SHOULD be within AC 220～230V, 50Hz, which will
make the MODEM under normal operation.
Last Step: Check the line connection to see if everything is ready. Then power up.
（figure2-1）
- 5 -

TD-8610 External ADSL MODEM User Guide
Chapter 3: How to use
3.1 Computer Configuration
1. Connect the cable according to Chapter 2, turn on the power.
2. Change the IP address of your PC（Figure 3-1）: Open TCP/IP Properties of the LAN
card in your PC, enter the IP address as 192.168.1.* (* is any value between 2 to
254, Netmask is 255.255.255.0, Gateway is 192.168.1.1, DNS address is the value
provided by ISP).
Figure 3-1
Please note:
the users of Windows 98 can open TCP/IP Properties according to the following:
Right-press (Mouse) Network Neighbor -> Choose Properties -> Double-press TCP/IP..
PCI Fast Ethernet Adapter.
- 6 -

TD-8610 External ADSL MODEM User Guide
The users of Windows 2000/NT/XP can do the following: Right-press Network Neighbor
-> Choose Properties -> Right-press Local Connection -> Choose Properties ->
Double-press Internet Protocol (TCP/IP).
NOTE: The words in fact maybe are different with this guide.
Remarks: you can check whether your configuration is successful through PING
command. Enter Ping 192.168.1.1
If the screen likes the following, you succeed.
Pinging 192.168.1.1 with 32 bytes of data:
Reply from 192.168.1.1: bytes=32 time<10ms TTL-128
…
If the screen likes the following, you fail. Please try again.
Pinging 192.168.1.1 with 32 bytes of data:
Request timed out.
3.2 Login
Startup Internet Explorer, and enter 192.168.1.1; then enter user name(admin)、
password(admin); you will see the page (Figure 3-2). When ADSL connecting is OK, you
will see some information such as link rate and soon.
(Figure 3-2)
Default value of user name and password is admin; if you want to change them, please
- 7 -

TD-8610 External ADSL MODEM User Guide
go to"Management","Password"changing them. (Figure 3-3)
(Figure 3-3)
3.3 Setup
1) Choose ATM PVCs Config (See Figure 3-4)
2) Enter VPI/VCI value which is provided by your ADSL service provider, press Save
to finish the configuration.You can press Next to add VPI/VCI value.
(Figure 3-4)
- 8 -

TD-8610 External ADSL MODEM User Guide
3.4 Software Dial
TD-8610 work in bridged(RFC 1483 Bridged) mode connecting Internet.you need to
install dial software on your PC.There are some software working on WINDOWS in
market,example for EnterNet3000 、RASPPPoE 、WinPeET.How to use the
software?Please refer to everyone’s operation instructions.
- 9 -

TD-8610 External ADSL MODEM User Guide
Appendix A: Default Config
USER NAME admin
PASSWORD admin
IP ADDRESS 192.168.1.1
VPI/VCI 0/32,1/33,0/35,0/100,0/200,8/35,8/81
- 10 -

TD-8610 External ADSL MODEM User Guide
Appendix B: Contact Information
For help with the installation or operation of the TP-LINK TD-8610 External ADSL
MODEM, please contact us.
E-mail: [email protected]
Website: http://www.tp-link.com
- 11 -