TP-Link JetStream TL-SL5428E User manual

Quick Installation Guide
TL-SL5428E
24-Port 10/100Mbps + 4-Port Gigabit
JetStream L2 Managed Switch
Rev 1.1.0

COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a
registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands
and product names are trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means
or used to make any derivative such as translation, transformation, or
adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD.
Copyright © 2011 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved.
http://www.tp-link.com
Package Contents
The following items should be found in your box:
¾One TL-SL5428E Switch
¾One Power Cord
¾One Console Cable
¾One Ground Cable
¾This Quick Installation Guide
¾Resource CD for the Switch, including:
•User Guide
•Other Helpful Information
¾Two mounting brackets and the fittings
Note:
Make sure that the package contains the above items. If any of the listed items
is damaged or missing, please contact with your distributor.

Preface
Thank you for purchasing the JetStream L2 Managed Switch! This Quick
Installation Guide provides the friendly step-by-step instructions for setting up
the JetStream L2 Managed Switch.
1. How to use this Quick Installation Guide?
This Quick Installation Guide is structured as follows:
Chapter 1 Product Introduction
This chapter describes the External Components of the Switch.
Chapter 2 Installation
This chapter illustrates how to install the Switch.
Chapter 3 Connection
This chapter illustrates how to do the physical connection of the Switch.
Chapter 4 Login to the Switch
This chapter instructs you to log in to the web management page of the Switch.
FAQ
This chapter contains information to help you solve the issues.
Appendix A: Specifications
This appendix provides the Switch’s technical specifications.
2. Conventions
The Switch or TL-SL5428E mentioned in this Quick Installation Guide stands
for TL-SL5428E 24-Port 10/100Mbps + 4-Port Gigabit JetStream L2 Managed
Switch without any explanation.
Symbol Description
Note
Remind to take note. The note contains the helpful
information for a better use of the Switch.
Caution Remind to be careful. A caution indicates a
potential which may result in device damage.

CONTENTS
Chapter 1 Product Introduction ................................................................1
1.1 Product Overview............................................................................1
1.2 Front Panel......................................................................................1
1.3 Rear Panel ......................................................................................2
Chapter 2 Installation .................................................................................3
2.1 Precautions .....................................................................................3
2.2 Installation ....................................................................................... 3
2.2.1 Desktop Installation.................................................................4
2.2.2 Rack Installation .....................................................................4
2.3 Connect to Ground.......................................................................... 6
Chapter 3 Connection ................................................................................8
3.1 Ethernet Ports .................................................................................8
3.2 SFP Ports........................................................................................8
3.3 Console Port ...................................................................................9
3.4 Power On ........................................................................................ 9
Chapter 4 Login to the Switch................................................................. 11
4.1 Login ............................................................................................. 11
4.2 Configuration................................................................................. 11
FAQ ...............................................................................................................13
Appendix A: Specifications.........................................................................14

1
Chapter 1 Product Introduction
1.1 Product Overview
TP-LINK JetStream L2 Managed Switch provides both Web and Command
Line management interface. The Embedded Web Interface supports remote
configuration, monitoring and troubleshooting. The EIA-standardized
framework together with smart configuration capacity can provide flexible
solutions for different scale of networks.
The TL-SL5428E provides 24 10/100Mbps auto-negotiation RJ45 ports, 4
10/100/1000Mbps Auto-Negotiation RJ45 ports, 2 SFP (Small Form-Factor
Pluggable) module ports (27F, 28F) and 1 Console port. The Port 27F (28F)
and Port 27T (28T) are referred to as “combo” ports, which means they cannot
be used simultaneously, otherwise only SFP ports work.
Port Feature:
Combo Ports
10Mbps/100Mbps
RJ45 Port
10Mbps/100Mbps/1000Mbps
RJ45 Port RJ45 Port SFP port
27T 27F
Port 1-24 Port 25-28
28T 28F
1.2 Front Panel
Figure 1-1 Front Panel
The following parts are located on the front panel of the Switch:
¾10/100Mbps Ports: Designed to connect to the device with a bandwidth of
10Mbps or 100Mbps. Each has a corresponding 10/100Mbps LED.
¾10/100/1000Mbps Ports: Designed to connect to the device with a
bandwidth of 10Mbps, 100Mbps or 1000Mbps. Each has a corresponding
1000Mbps LED.
¾SFP Ports: Designed to install the SFP module. Port 27F shares the same
LED with Port 27T and Port 28F shares the same LED with Port 28T.
¾Console Port: Designed to connect with the serial port of a computer or
terminal for monitoring and configuring the Switch.
L5428E

2
¾LEDs
Name Status Indication
On Power is on.
Flashing Power supply is abnormal.
PWR
Off Power is off or power supply is abnormal.
On The Switch is working abnormally.
Flashing The Switch is working normally.
SYS
Off The Switch is working abnormally.
On A device is linked to the corresponding port.
Flashing Data is being transmitted or received.
Green The linked device is running at 100Mbps.
10/100Mbps
Yellow The linked device is running at 10Mbps.
On A device is linked to the corresponding port.
Flashing Data is being transmitted or received.
Green The linked device is running at 1000Mbps.
1000Mbps
Yellow The linked device is running at 10/100Mbps.
1.3 Rear Panel
The rear panel of TL-SL5428E features a power socket and a Grounding
Terminal (marked with ).
Figure 1-2 Rear Panel
¾Grounding Terminal: TL-SL5428E already comes with Lightning
Protection Mechanism. You can also ground the Switch through the PE
(Protecting Earth) cable of AC cord or with Ground Cable. For detail
information, please refer to section 2.3 Connect to Ground.
¾AC Power Socket: Connect the female connector of the power cord here,
and the male connector to the AC power outlet. Please make sure the
voltage of the power supply meets the requirement of the input voltage
(100-240V~ 50/60Hz 0.6A).

3
Chapter 2 Installation
2.1 Precautions
To ensure a long-term and stable performance of the Switch, please pay
attention to the following before the installation.
1) Safety Requirements
•Before cleaning the Switch, cut off the power supply. Do not clean it by
the waterish cloth, and never use any other liquid cleaning method.
•Take waterproof measures during storage, transportation and operation
of the equipment.
•Use only the power cord provided with the Switch.
•Make sure the voltage of the power supply meets the requirement of the
input voltage of the Switch.
•Do not push any objects into the openings of the Switch.
•Ensure the vent hole is well ventilated and unblocked.
•Do not open or remove the cover of the Switch.
2) Location Requirements
When you choose a location for the Switch, please follow these guidelines:
•Install the Switch on a flat and stable surface that can support the entire
weight of the Switch with all fittings.
•Locate the Switch far from strong electromagnetic field generators
(such as motors), vibration, dust, and direct exposure to sunlight.
•To ensure adequate air flow around the Switch. At least 10 cm (4 inches)
of space at the front and rear of the Switch is needed for ventilation.
•Make sure that the Switch will be accessible and that the cables can be
easily connected.
•Position the Switch away from water and moisture sources, be sure to
provide an acceptable temperature and humidity operating
environment.
2.2 Installation
This Switch can be either installed on the standard 19-inch mountable rack or
located on the desktop.
Caution:
Please unplug the power cord before installing or removing the Switch.

4
2.2.1 Desktop Installation
To install the Switch on the desktop, please follow the steps:
1) Set the Switch on a flat surface strong enough to support the entire weight
of the Switch with all fittings.
2) Remove the adhesive backing papers from the rubber feet.
3) Turnover the Switch and attach the supplied rubber feet to the recessed
areas on the bottom at each corner of the Switch.
Figure 2-1 Attaching Rubber Feet
4) Upturn the Switch and connect it to the network devices while keep enough
ventilation space around.
5) Connect the Switch to power source with the provided power cord.
Caution:
Please avoid any heavy thing placed on the Switch.
2.2.2 Rack Installation
To install the Switch in an EIA standard-sized, 19-inch rack, follow the
instructions described below:
1) Secure the supplied rack-mounting brackets to each side of the Switch with
supplied screws, as illustrated in the following figure.
L5428E

5
Figure 2-2 Attaching Brackets
2) After the brackets are attached to the Switch, use suitable screws (not
provided) to secure the brackets to the rack, as illustrated in the following
figure.
Figure 2-3 Mounting Switch
3) Connect the Switch to network devices.
4) Supply power to the Switch with the provided power cord.
L5428E
L5428E

6
2.3 Connect to Ground
Connecting the Switch to ground is to quickly release the lightning over-voltage
and over-current of the Switch, which is also a necessary measure to protect the
body from electric shock.
In different environments, the Switch may be grounded differently. The following
will instruct you to connect the Switch to the ground in two ways, connecting to
the Grounding Bar or connecting to the Ground via the power cord. Please
connect the Switch to ground in the optimum way according to your specific
operation environment.
•Connecting to the Grounding Bar
If the Switch is installed in the Equipment Room, where a Grounding Bar is
available, you are recommended to connect the Switch to the Grounding Bar as
shown in the following figure.
Figure 2-4
Note:
The Grounding Bar is not provided with our product.
Switch (Rear Panel)
Ground Cable
Grounding Terminal
Grounding Bar

7
•Connecting to the Ground via the power supply
If the Switch is installed in the normal environment, the Switch can be grounded
via the PE（Protecting Earth）cable of the AC power supply as shown in the
following figure.
Figure 2-5
* The figure is to illustrate the application and principle. The power plug you get from the
package and the socket in your situation will comply with the regulation in your country, so
they may differ from the figure above.
Note:
If you intend to connect the Switch to the ground via the PE (Protecting Earth)
cable of AC power cord, please make sure the PE (Protecting Earth) cable in
the electrical outlet is well grounded in advance.

8
Chapter 3 Connection
3.1 Ethernet Ports
The Switch has 24 10/100Mbps and 4 10/100/1000Mbps auto-negotiating,
auto MDI/MDIX Ethernet ports, which can be directly connected to the network
devices by RJ45 cable as the following figure shown.
Figure 3-1 Connecting the RJ45 Port
3.2 SFP Ports
The Switch features two SFP (Small Form-Factor Pluggable) transceiver slots
that are shared with two associated 1000Base-T RJ45 ports. If an SFP
transceiver (purchased separately) is installed in a slot and has a valid link on
the port, the associated RJ45 port will be disabled and cannot be used.
Note:
TL-SL5428E supports 100/1000Base-FX SFP module at full-duplex mode.
Figure 3-2 Inserting SFP Module
L5428E
L5428E

9
3.3 Console Port
The Switch features a console interface for configuring the Switch using CLI
(Command Line Interface).
Caution:
The serial port of the computer doesn’t support plug-and-play feature, please
make sure the Switch is powered off before connecting the console cable to
the computer.
Connect the console port of the Switch and your computer with a console
cable as shown in Figure 3-3.
Figure 3-3 Connecting the Console Port
3.4 Power On
Plug in the negative connector of the provided power cord into the power
socket of the Switch, and the positive connector into a power outlet as shown
in Figure 3-4.
L5428E

10
Figure 3-4 Connecting to Power Supply
* The figure is to illustrate the application and principle. The power plug you get from the
package and the socket in your situation will comply with the regulation in your country, so
they may differ from the figure above.
Powering on the Switch, it will automatically initialize and its LED indicators will
respond as follows:
1) All of the 10/100Mbps and 1000Mbps LED indicators will flash momentarily
and then turn off, which represents a resetting of the system.
2) The PWR LED indicator will light on all the time.
3) The SYS LED indicator will flash, which represents a successful
initialization.
Note:
If the LED indicators don’t respond as described above, please check the
power supply and its connection.

11
Chapter 4 Login to the Switch
4.1 Login
1) To access the configuration utility, open a web-browser and type in the
default address http://192.168.0.1 in the address field of the browser, then
press the Enter key.
Figure 4-1 Web-browser
Note:
To log in to the Switch, the IP address of your PC should be set in the same
subnet addresses of the Switch. The IP address is 192.168.0.x ("x" is any
number from 2 to 254), Subnet Mask is 255.255.255.0.
For the detailed instructions as to how to do this, please refer to Appendix B in
the User Guide on the Resource CD.
2) After a moment, a login window will appear, as shown in Figure 4-2. Enter
admin for the User Name and Password, both in lower case letters. Then
click the Login button or press the Enter key.
Figure 4-2 Login
4.2 Configuration
After a successful login, the main page will appear as Figure 4-3, and you can
configure the function by clicking the setup menu on the left side of the screen.

12
Figure 4-3 Main Setup-Menu

13
FAQ
How to restore the Switch to its factory default settings?
Please access the Web-based configuration page: choose menu ĐSystemŚ
System ToolsŚSystem Resetđ, click the Reset button on the corresponding
page.
What can I do if I could not access the web-based
configuration page?
It is recommended that you should check the following items:
1) Check per port LED on the Switch and make sure the cable is installed
properly.
2) Make sure the IP address of your PC is set in the same subnet addresses
of the Switch. Restore the Switch to its factory defaults. And then the IP
address can be set as 192.168.0.x ("x" is any number from 2 to 254),
Subnet Mask is 255.255.255.0.
3) Try another port on the Switch and make sure the cable is the right type.
4) Turn off the power. After a while, turn on the power again.
What can I do if I could not access the Internet?
Make sure your web browser is configured correctly. Ensure the software
blocking the pop-up screen is disabled, and your web browser is not working
on Work Offline mode.

14
Appendix A: Specifications
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX/100Base-FX Fast Ethernet
IEEE 802.3ab 1000Base-T Gigabit Ethernet
IEEE 802.3z 1000Base-X Gigabit Ethernet
Standards
IEEE 802.3x Flow Control
10Base-T: UTP/STP of Cat. 3 or above
100Base-TX: UTP/STP of Cat. 5
100Base-FX: MMF or SMF SFP Module (Optional)
1000Base-T: 4-pair UTP (≤100m) of Cat. 5 or above
Transmission
Medium
1000Base-X: MMF or SMF SFP Module (Optional)
Operating Temperature: 0℃~ 40℃
Storage Temperature: -40℃~ 70℃
Operating Humidity: 10% ~ 90% RH Non-condensing
Operating
Environment
Storage Humidity: 5% ~ 90% RH Non-condensing

15
Technical Support
For more troubleshooting help, go to:
www.tp-link.com/support/faq.asp
To download the latest Firmware, Driver, Utility and User Guide, go to:
www.tp-link.com/support/download.asp
For all other technical support, please contact us by using the following details:
Global
Tel: [phone]
E-mail: [e-mail]
Service time: 24hrs, 7days a week
Singapore
Australia & New Zealand
Tel: AU 1300 87 5465
NZ 0800 87 5465
E-mail: [e-mail]
Service time: 24hrs, 7days a week
Tel: [phone]
E-mail: support.s[email protected]
Service time: 24hrs, 7days a week
UK
Tel: [phone]
E-mail: [e-mail]
Service time: 24hrs, 7days a week
USA/Canada
Toll Free: [phone]
E-mail: support.u[email protected]
Service time: 24hrs, 7days a week
Switzerland
Tel: [phone] (German
service)
E-mail: support.c[email protected]
Fee: 4-8 Rp/min, depending on
rate of different time
Service Time: Monday to Friday
9:00 AM to 6:00 PM. GMT+1 or
GMT+2 (Daylight Saving Time)
Malaysia
Tel: [phone] (1300 88TPLINK)
Email: [e-mail]
ServiceTime: 24 hours a day, 7 days a
week
Turke y
Tel: [phone]（Turkish Service）
E-mail: [e-mail]
Service time: 9:00 AM to 6:00 PM,
7days a week
Germany / Austria
Tel: [phone] (German Service)
/ +49 1805 TPLINK
E-mail: [e-mail]
Fee: 0.14 EUR/min from the German
fixed phone network and up to 0.42
EUR/min from mobile phone
Service time: Monday to Friday 9:00 AM
to 6:00 PM.GMT+ 1 or GMT+ 2
(Daylight Saving Time in Germany)
*Except bank holidays in Hesse

7106503505