TP-Link TL-SF1005D User manual

Connection
7106507237 REV13.0.2
Installation Guide
10/100Mbps Desktop Switch
TL-SF1005D/TL-SF1008D
TL-SF1016D/TL-SF1024M
LED Explanation
Power
On: Power on
O: Power o
Link/Act
On: Link present but no activity
Flashing: Transmitting/receiving data
O: No link
For simplicity, we will take TL-SF1005D for example throughout this Guide.
Ethernet Ports (1-5) Power Cord
PC PC
Router
LAN PortWAN Port
Internet
Package Contents: Switch, Power Adapter and Installation Guide.
All manuals and user guides at all-guidesbox.com
all-guidesbox.com

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause undesired
operation.
Any changes or modications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
FCC STATEMENT
Frequently Asked Questions (FAQ)
The Power LED should be lit when the power system is working normally.
If the Power LED is not lit, please check as follows:
A1: Make sure the power cord is connected to the switch with power
source properly.
A2: Make sure the voltage of the power supply meets the requirements
of the input voltage of the switch.
A3: Make sure the power source is ON.
Q1. The Power LED is not lit.
It is recommended that you check the following items:
A1: Make sure that the cable connectors are rmly plugged into the
switch and the device.
A2
: Make sure the connected device is turned on and working well.
A3
: The cable must be less than 100 meters long (328 feet).
Q2. The Link/Act LED is not lit when a device is connected
to the corresponding port.
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
0˚C to 40˚C (32˚F to 104˚F)
-40˚C to 70˚C (-40˚F to 158˚F)
10% to 90%RH non-condensing
5% to 90%RH non-condensing
Environmental and Physical Specications
IEEE 802.3, IEEE 802.3i, IEEE 802.3u, IEEE 802.3x
CSMA/CD
5/8/16/24 10/100Mbps Auto-Negotiation RJ45 Ports
10BASE-T: UTP category 3, 4, 5 cable (≤100m)
EIA/TIA-568 100
Ω STP (≤100m)
100BASE-TX: UTP category 5, 5e cable (≤100m)
EIA/TIA-568 100
Ω STP (≤100m)
Power, Link/Act LEDs
Ethernet: 10Mbps (Half Duplex), 20Mbps (Full Duplex)
Fast Ethernet: 100Mbps (Half Duplex), 200Mbps (Full
Duplex)
Store-and-Forward
Automatically learning, automatically aging
10Base-T: 14880pps/Port
100Base-Tx: 148800pps/Port
10Base-T: 14880pps/Port
100Base-Tx: 148800pps/Port
Standard
Protocol
Interface
Network Media (Cable)
LED indicators
Data Transfer Rate
Transfer Method
MAC Address Learning
Frame Filter Rate
Frame Foward Rate
General Specications
Specications
This is a class B product. In a domestic
environment, this product may cause radio
interference, in which case the user may
be required to take adequate measures.
CE Mark Warning
Do not use this product near water,
for example, in a wet basement or
near a swimming pool.
Avoid using this product during an
electrical storm. There may be a
remote risk of electric shock from
lightning.
SAFETY NOTICES
Cautions
Industry Canada Statement
CAN ICES-3 (B)/NMB-3(B)
BSMI Notice
安全諮詢及注意事項
請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。
注意防潮，請勿將水或其他液體潑灑到本產品上。
插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。
請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。
請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。
Use only power supplies
which are provided by
manufacturer and in the original
packing of this product.
Safety Information
Explanation of the symbols on the product label
DC voltage
RECYCLING
This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE).
This means that this product must be handled pursuant to European directive 2012/19/EU in order to
be recycled or dismantled to minimize its impact on the environment.
User has the choice to give his product to a competent recycling organization or to the retailer when
he buys a new electrical or electronic equipment.
Indoor use only
For technical support and other information, please visit
http://www.tp-link.com/support, or simply scan the QR code.
Some models featured in this guide may be unavailable in your country or region.
For local sales information, visit http://www.tp-link.com.
© 2017 TP-Link
All manuals and user guides at all-guidesbox.com