TP-Link TL-SF1048 User manual

71035627
µ÷Öƽâµ÷Æ÷
Rev 4.0
16/24/48-port 10/100M Fast Ethernet Switch16/24/48-port 10/100M Fast Ethernet Switch
TL-SF1016
TL-SF1024
TL-SF1048
TL-SF1016
TL-SF1024
TL-SF1048
User's Guide

COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered
trademark of TP-LINK Technologies Co., Ltd. Other brands and product
names are trademarks or registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means
or used to make any derivative such as translation, transformation, or
adaptation without permission from TP-LINK Technologies Co., Ltd. Copyright
© 2006 TP-LINK Technologies Co., Ltd. All rights reserved.
FCC STATEMENT
The 16/24/48-port 10/100M Fast Ethernet Switch has been tested and found
to comply with the limits for a class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
ØReorient or relocate the receiving antenna.
ØIncrease the separation between the equipment and receiver.
ØConnect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
ØConsult the dealer or an experienced radio/TV technician for help.
EC DECLARATION OF CONFORMITY (EUROPE)
In compliance with the EMC Directive 89/336/EEC, Low Voltage Directive
73/23/EEC, this product meets the requirements of the following standards:
ØEN55022
ØEN55024
ØEN60950
SAFETY NOTICES
Caution:
Do not use this product near water, for example, in a wet basement or near a
swimming pool.
Avoid using this product during an electrical storm. There may be a remote
risk of electric shock from lightning.

TL-SF1016/TL-SF1024/TL-SF1048
10/100M Fast Ethernet Switch User's Guide
Package Contents
The following contents should be found in your box:
ØOne TL-SF1016/TL-SF1024/TL-SF1048 Switch
ØOne power cord
ØThis User's Guide
ØMounting screws and two “L”planks
Note: If any of the above contents are damaged or missing, please
contact the retailer from whom you purchased the TL-SF1016/TL-SF1024/TL-
SF1048 16/24/48-port 10/100M Switch for assistance.
Chapter 1: Introduction of the Product
This chapter describes the features of the model of TL-SF1016/TL-
SF1024/TL-SF1048 16/24/48-port10/100M Switch. TL-SF1016, TL-SF1024,
and TL-SF1048 just differ in the number of LED indicators and ports, all
figures in this guide are of TL-SF1024.
1.1 Overview of the product
TL-SF1016/TL-SF1024/TL-SF1048 16/24/48-port 10/100M Switch provides
16/24/48 10/100Mbps Auto-Negotiation RJ45 ports. Each port of the TL-
SF1016/TL-SF1024/TL-SF1048 supports auto MDI/MDI-X function,
eliminating the need for crossover cables or Uplink ports. The Switch is Plug-
and-Play and any port can be simply plugged into a server, a hub or a switch,
using straight cable or crossover cable.
The TP-LINK TL-SF1016/TL-SF1024/TL-SF1048 16/24/48-port 10/100M
Package Contents...........................................................................................1
Chapter 1: Introduction of the Product.........................................................1
1.1 Overview of the product............................................................................1
1.2 Features....................................................................................................2
Chapter 2: Installation....................................................................................2
2.1 Mounting the Switch on a Desk................................................................2
2.2 Mounting the Switch in a Rack..................................................................3
2.3 Power on...................................................................................................4
Chapter 3: Identifying External Components...............................................4
3.1 Front Panel...............................................................................................4
3.2 Rear Panel................................................................................................4
3.3 LED indicators...........................................................................................5
Appendix A: Specifications............................................................................6
Appendix B: Troubleshooting........................................................................7
Appendix C: Contact Information..................................................................7
TABLE OF CONTENTS
1

TL-SF1016/TL-SF1024/TL-SF1048
10/100M Fast Ethernet Switch User's Guide
TL-SF1016/TL-SF1024/TL-SF1048
10/100M Fast Ethernet Switch User's Guide
Power
Link
Act
100Mbps
100Mbps
1357911131517192123
24681012141618202224
1357911131517192123
24681012141618202224
Link
Act
TL-SF1024
10/100MbpsFastEthernetSwitch
Power
Link
Act
100Mbps
100Mbps
1357911 131517192123
24681012 141618202224
1357911131517192123
24681012141618202224
Link
Act
TL-SF1024
10/100MbpsFastEthernetSwitch
2.2 Mounting the Switch in a Rack
The dimension of TL-SF1016/TL-SF1024/TL-SF1048 is designed according to
the standard 19”rack-mountable steel case of Electronic Industries
Association.
Power off all the equipment connected to the Switch before mounting it in the
rack, then rivet the two “L”brackets onto each side of the Switch, and fasten it
with screws in the rack.
Figure 2-1 Rivet the “L”brackets onto the Switch
Figure 2-2 Fasten the Switch in the Rack
2
switch provides you with a low-cost, easy-to-use, high-performance, seamless
and standard upgrade to improve your old network to a 100Mbps network. It
will boost your network performance up to full duplex data transfer.
1.2 Features
ØComplies with IEEE802.3, IEEE802.3u standards
Ø16/24/48 10/100Mbps Auto-Negotiation RJ45 ports supporting Auto-
MDI/MDIX
ØSupports IEEE802.3X flow control for full-duplex mode and
backpressure for half-duplex mode
ØLED indicators for monitoring power, link, activity, speed (TL-SF1024)
ØStandard 19”rack-mountable steel case
ØInternal power supply
Chapter 2: Installation
2.1 Mounting the Switch on a Desk
Before placing the Switch on a desk, attach four rubber feet to the flutes on
the Switch bottom, then lay the Switch on the desktop, where it is able to
withstand 5kg of weight.
Note: Make sure there is a grounded AC outlet within 1.5 meters, and
working well;
Make sure there is free space for radiating heat and airflow.
Be sure not to lay anything heavy on top.
3

Figure 3-2 TL-SF1024 Switch Rear Panel sketch
3.3 LED indicators
The LED indicators include Power, Link/Act LED indicators, which are used
for monitoring and pre-troubleshooting of the Switch. The following section
shows the LED indicators of the Switch along with an explanation of each
indicator.
Figure 3-3 TL-SF1024 Switch LEDs sketch
ØPower LED: This indicator will light solid red when the Switch powers
up. If the LED is not lit, please check the power supply and connection.
ØLINK/ACT LED: The LED indicates Link/Active status. The
corresponding LED indicator will light solid green when connected to a
network device. It flashes green when data is being transmitted or
received on the working connection.
Ø100Mbps:The corresponding gigabit port LED indicator will light solid
green when it's working on 100Mbps speed, not lit when working on
10Mbps speed.
Note: Because of the difference of among the mode of switch,Some
switch don't include the 100Mbps indicator,such as TL-SF1048 and a
few of TL-SF1016 switch.
TL-SF1016/TL-SF1024/TL-SF1048
10/100M Fast Ethernet Switch User's Guide
TL-SF1016/TL-SF1024/TL-SF1048
10/100M Fast Ethernet Switch User's Guide
Power
Link
Act
100Mbps
100Mbps
1357911 13 15 17 19 21 23
246 8 10 12 14 16 18 20 22 24
Link
Act
TL-SF1024
10/100Mbps Fast Ethernet Switch
100-240V~50-60Hz 0.6A
2.3 Power on
The TL-SF1016/TL-SF1024/TL-SF1048 16/24/48-port 10/100M Switch is
powered by an AC Power Supply. Connect the Switch and power outlet by
power cord. Powering on the Switch, it will be automatically initialized and the
LED indicators should respond as follows:
1) All of the LED indicators will flash momentarily for one second, which
represent a resetting of the system.
2) The Power LED indicator will light up.
Chapter 3: Identifying External Components
This Chapter describes the front panel, rear panel and LED indicators of the
Switch.
3.1 Front Panel
The front panel of TL-SF1024 consists of switch model, switch LED indicators,
and 24 10/100Mbps RJ-45 ports.
Figure 3-1 TL-SF1024 Switch Front Panel sketch
3.2 Rear Panel
The rear panel of TL-SF1024 only features an electrical outlet, which is an AC
electrical outlet. Connect the female of the power cord head here, and the
male head to the AC power.
Power
Link
Act
100Mbps
100Mbps
1357911 13 15 17 19 21 23
246 8 10 12 14 16 18 20 22 24
1357911 13 15 17 19 21 23
246 8 10 12 14 16 18 20 22 24
Link
Act
TL-SF1024
10/100Mbps Fast Ethernet Switch
45

TL-SF1016/TL-SF1024/TL-SF1048
10/100M Fast Ethernet Switch User's Guide
Appendix B: Troubleshooting
Appendix C: Contact Information
For help with the installation or operation of the TP-LINK TL-SF1016/TL-
SF1024 /TL-SF1048 16/24/48-port 10/100M Switch, please contact us.
E-mail: [email protected]
Website: http://www.tp-link.com
1. The Power LED is not lit
ØMake sure the AC power cord connected the Switch with power source
properly.
ØMake sure the power source is ON.
2. The Link/Act LED is not lit when a device is connected to the
corresponding port
ØMake sure that the cable connectors are firmly plugged into the Switch
and the device.
ØMake sure the connected device is turned on and working well.
ØThe cable must be less than 100 meters long(328 feet).
TL-SF1016/TL-SF1024/TL-SF1048
10/100M Fast Ethernet Switch User's Guide
Appendix A: Specifications
Environmental and Physical
Dimensions(W D H) TL-SF1016:11.57 7.1 1.73 in.(294 180 44 mm)
TL-SF1024:17.3 7.1 1.73 in. (440 180 44 mm)
TL-SF1048:17.3 10.2 1.73 in.(440 260 44 mm)
Power Supply Output 100-240V~ 50-60Hz (Internal universal power supply)
Operating Temperature 0 ~40 (32 ~104 )
Storage Temperature -40~70 (-40 ~158 )
Operating Humidity 10%~90% non-condensing
Storage humidity 5%~95% non-condensing
67
General
Standards IEEE802.3 10Base-T
IEEE802.3u 100Base-TX
Topology Star
Protocol CSMA/CD
Data Transfer Rate Ethernet: 10Mbps (Half Duplex)
20Mbps (Full Duplex)
Fast Ethernet: 100Mbps (Half Duplex)
200Mbps (Full Duplex)
Number of Ports 16/24/48 10/100Mbps Auto-Negotiation RJ-45 ports
LED indicators Power, Link/Act, 100M(TL-SF1024)