TP-Link POE150S User manual

Installation Guide
PoE InjectorPower Socket Ethernet Device
(switch, router, etc.)
PoE Injector
LAN IN PWR DC 48V
PoE Injector Only The PoE Injector supplies steady power and data connectivity to a powered device such as PoE IP Camera, PoE
AP and PoE IP Phone through an Ethernet cable.
IP Camera AP IP Phone
Powered Device (PD)
Note:
Set the required voltage
of the non-PoE device
before cable connection.
12V 9V 5V
PoE Splitter
LAN OUT PWR DC OUT
PoE Splitter
Non-PoE Device
(suggested power:<12 W)
PoE/PoE+ Switch
PoE Splitter Only The PoE Splitter can be used with a PoE/PoE+ switch to deliver direct current (DC) power and data to a Non-PoE
device.
PoE Injector PoE SplitterPower Socket
Ethernet Device
(switch, router, etc.)
Note:
Set the required voltage
of the non-PoE device
before cable connection.
12V 9V 5V
PoE Injector
LAN IN PWR DC 48V LAN OUT PWR DC OUT
PoE Splitter
Non-PoE Device
(suggested power:<12 W)
PoE Injector & Splitter The PoE injector and PoE splitter can be used as a kit to supply power and transmit data to a Non-PoE
device.
Some models featured in this guide may be unavailable in your country or region. For local sales information, visit https://www.tp-link.com.
For technical support and other information, please visit
https://www.tp-link.com/support, or simply scan the QR code.
To ask questions, find answers, and communicate with TP-Link users or
engineers, please visit https://community.tp-link.com to join TP-Link
Community.
© 2023 TP-Link 7106510639 REV6.20.0
PoE Injector and PoE Splitter
For simplicity, we will take POE150S and POE10R for example throughout the Guide, other models may dier in appearance.
Note: The maximum output power of POE150S is
15.4W. PoE devices that require more than 15.4W are
not supported.

PoE Injector: PoE Splitter:
Power LED Explanation
On:Connected to PSE correctly
O:No PSE is connected
LAN OUT PWR DC OUT
PoE Splitter
PoE Injector
LAN IN PWR DC 48V
On: Supplying power normally
O: No power supply
Safety Information
Keep the device away from water, re, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need
service, please contact us.
Do not use any other chargers than those recommended.
Do not use damaged charger or USB cable to charge the device.
Adapter shall be installed near the equipment and shall be easily accessible.
Please read and follow the above safety information when operating the device.
We cannot guarantee that no accidents or damage will occur due to improper
use of the device. Please use this product with care and operate at your own
risk.
A: Yes. All RJ45 ports of the PoE injector support 10/100/1000 Mbps
auto-negotiation.
Q1. Can the PoE injector supply power to a PoE device which
doesn’t have a gigabit PoE port?
A1: Ensure the PD is PoE-compliant and its connecting port supports the PoE
function.
A2: Ensure the power consumption of the PD doesn’t exceed 15.4 W,
otherwise the overload protection of the PoE injector will be activated. The
quality and length of the Ethernet cable may inuence the reception of the
power supply.
Q2. What can I do if my PoE injector doesn’t supply power to
the powered device or the supplied power is unstable?
FAQ
Q3. Must I use the PoE injector together with the PoE splitter?
A: No. The PoE injector can supply power to all PDs support PoE function. The
PoE splitter is used with a PoE switch or the PoE injector to supply power to
a non-PoE device.
A1: Ensure the power cord is connected the PoE injector with power source
properly.
A2: Ensure the power consumption of the PD doesn’t exceed 15.4 W,
otherwise the PoE injector will activate the overload protection and the
power will be cut o.
Q4. The Power LED of PoE injector is not lit.
Operating Temperature 0˚C to 40˚C (32˚F to 104˚F)
Storage Temperature -40˚C to 70˚C (-40˚F to 158˚F)
Storage Humidity 5% to 90% non-condensing
Operating Humidity 10% to 90% non-condensing
Environmental and Physical Specifications
Ports
Specications
IEEE 802.3i, IEEE802.3u, IEEE 802.3ab, IEEE 802.3af
Standards
PWR
UTP/STP of Cat. 5 or above (based on the standards that the
connected devices comply with)
LED
Cable Type
General Specifications
POE10R:
10/100/1000 Mbps Auto-Negotiation RJ45 POWER+DATA
IN Port
10/100/1000 Mbps Auto-Negotiation RJ45 LAN OUT Port
5V / 9V / 12V DC OUT Power Output Port
POE150S:
10/100/1000 Mbps Auto-Negotiation RJ45 LAN IN Port
10/100/1000 Mbps Auto-Negotiation RJ45 POWER+DATA
OUT Port
DC 48 V Power Input Port
EU Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of directives 2014/30/EU,
2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.
The original EU declaration of conformity may be found at
https://www.tp-link.com/en/ce.
UK Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of the Electromagnetic Compatibility
Regulations 2016 and Electrical Equipment (Safety) Regulations 2016.
The original UK Declaration of Conformity may be found at
https://www.tp-link.com/support/ukca
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на
відповідність вимогам нормативних документів та вимогам, що передбачені
чинними законодавчими актами України.
Responsible party:
TP-Link USA Corporation
Address: 10 Mauchly, Irvine, CA 92618
Website: https://www.tp-link.com/us/
Tel: [phone]
Fax: [phone]
E-mail: [email protected]
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the
applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the
equipment is properly maintained and operated.
Issue Date: 2024.01.24
Component Name Model
I.T.E. POWER SUPPLY T480038-2B1
Product Name: PoE Splitter
Model Number: POE10R
Product Name: PoE Injector
Model Number: POE150S
Product Name: I.T.E. POWER SUPPLY
Model Number: T480038-2B1
Responsible party:
TP-Link USA Corporation
Address: 10 Mauchly, Irvine, CA 92618
Website: https://www.tp-link.com/us/
Tel: [phone]
Fax: [phone]
E-mail: [email protected]
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the
applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the
equipment is properly maintained and operated.
Issue Date: 2024.01.24
FCC compliance information statement
FCC compliance information statement
This is a class B product. In a domestic environment, this product may cause radio interference, in which case the
user may be required to take adequate measures.
CE Mark Warning
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних
документів та вимогам, що передбачені чинними законодавчими актами України.
CAN ICES-3 (B)/NMB-3(B)
Industry Canada Statement
BSMI Notice (For POE150S)
安全諮詢及注意事項
請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。
注意防潮，請勿將水或其他液體潑灑到本產品上。
插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。
請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。
請不要私自拆開機殼或自行維修，如產品有故障請與原廠或代理商聯繫。
限用物質含有情況標示聲明書
產品元件名稱
PCB
外殼
電源供應器
其他及其配件
限用物質及其化學符號
備考1： "○"系指該項限用物質之百分比含量未超出百分比含量基準值。
備考2： " - " 系指該項限用物質為排除項目。
○ ○ ○ ○ ○
鉛
Pb
○
○
-
-
鎘
Cd
○
○
汞
Hg
○
○
六價鉻
Cr+6
○
○
多溴聯苯
PBB
○
○
多
溴二苯醚
PBDE
○
○
○ ○ ○ ○ ○
E
xplana�on of the symbols on the product label
S
ymbols may vary from products. The label is at the bottom of the product.
Symbol
Explanation
Cla ss II equipment
Cla ss II equipment with functional earthing
Alternating current
Direct current
Pol arity of d.c. power connector
For indoor use only
Dangerous voltage
Caution, risk of electric shock
Ene rgy eciency Marking
Protective earth
Earth
Frame or chassis
Functional earthing
Caution, hot surface
Caution
Operator's manual
Stand-by
"ON"/"OFF" (push-push)
Fus e
Fuse is used in neutral N
Cauti on, avoid listening a t high vol ume l evels for long periods
Di sconnection, a llpower plugs
m Switch of mini-gap construction
µ
Switch of micro- gap construction (for US version)
Switch of micro-gap /micro - disconnection construction
(for other versions except US)
ε Switch without contact gap (Semiconductor switching device)
RECYCLING
This product bears the selective sorting symbol for Waste
electrical and electronic equipment (WEEE). This means that
this product must be handled pursuant to European directive
2012/19/EU in order to be recycled or dismantled to minimize its
impact on the environment.
User has the choice to give his product to a competent recycling
organization or to the retailer when he buys a new electrical or
electronic equipment.