TP-Link Auranet EAP110 User manual

7106506406 REV1.0.0
Specifications are subject to change without notice. TP-LINK is a registered
trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product
names are trademarks or registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any
means or used to make any derivative such as translation, transformation,
or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD.
Copyright © 2016 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved.
www.tp-link.com
›English
›Español
›Français
› Português
Ceiling Mount Access Point
Installation Guide
Guía de Instalación
Guide d'installation
Guia de Instalação

CONTENTS
English..................................................................................................1
Español.................................................................................................7
Français..............................................................................................13
Português ...........................................................................................19

1
English
Note: The image may differ from the actual product.
Network Topology
A typical network topology for the EAP is shown below.
EAP Controller
A DHCP server (typically a router) is required to assign IP addresses to the EAPs
and clients in your local network. A computer running the EAP Controller software,
which can be in the same or different subnet with the EAPs, is used to centrally
manage the EAPs.
You can get the EAP Controller software from our website http://www.tp-link.com.
Hardware Installation
■Option1：
Ceiling Rail Mounting
Follow the steps below to install the EAP with the provided accessories:
1Position the Ceiling T-rail Clip and push the
movable part toward the rail base.
Ceiling T-rail Clip M3×6 Pan-head Screws (Qty.5)
Controller
Host
Router Switch
Internet
Clients
EAP
EAP
EAP

2
English
2Use an M3×6 pan-head screw to secure the T-rail
Clip onto the ceiling rail.
3Attach the mounting bracket to the Ceiling T-rail
Clip using four M3x6 pan-head screws.
4Attach the EAP to the mounting bracket by
aligning ARROW 1 (on the EAP) with ARROW 2
(on the mounting bracket), then rotate the EAP
clockwise until it locks into place.
5Connect the Ethernet cable to the ETHERNET
port.

3
English
■Option2：
Ceiling Mounting
Follow the steps below to install the EAP with the provided accessories:
1Remove the ceiling tile.
2Place the mounting bracket in the center
of the ceiling tile. Mark the three positions
of the screw holes and a 10mm hole for
the Ethernet cable to feed through. Drill
three 4mm holes and a 10mm hole for the
Ethernet cable.
X3
3Secure the mounting bracket to the ceiling
tile using three M3x30 pan-head screws,
washers and wing nuts.
Washers
(Qty.3)
M3×30 Pan-head Screws
(Qty.3)
Wing Nuts
(Qty.3)
Hole for Ethernet cable

4
English
4Attach the EAP to the mounting bracket by
aligning ARROW 1 (on the EAP) with ARROW
2 (on the mounting bracket), then rotate the
EAP clockwise until it locks into place.
5Feed the Ethernet cable through the hole and
set the ceiling tile back into place. Connect
the Ethernet cable to the ETHERNET port.
■Option3：
Wall Mounting
Follow the steps below to install the EAP with the provided accessories:
1Attach the EAP to the mounting bracket by
aligning ARROW 1 (on the EAP) with ARROW 2
(on the mounting bracket), then rotate the EAP
clockwise until it locks into place.
2Make two small pencil marks on the wall. Make
sure the two marks are level and should be
98.6mm apart. Drill two 6mm holes through
the center of your marks.
98.6mm
M3×28 Plastic Wall Anchors
(Qty.4)
M3×20 Self-tapping Screws
(Qty.4)

5
English
3Insert the plastic wall anchors into the 6mm
holes and drive the self-tapping screws into the
anchors. Do not drive the screws all the way in
and leave enough clearance to hang the EAP.
4Hang the EAP on the screws. Make sure the
EAP is firmly seated against the wall.
5Connect the Ethernet cable to the ETHERNET
port on the EAP.

6
English
Power Supply
■Power via PSE Device or Power Adapter
If the product is provided with a power adapter, power the device via a PSE device
(such as a PoE switch) or the power adapter.
Via PoE Switch
ON/OFF
1
2
Via Power Adapter
ON/OFF
1
2
■Power via POE Adapter
If the product is provided with a POE adapter, power the device via the POE
adapter.
1
3
PoE LAN
2
PoE Switch
PoE Adapter
(Up to 100m)
Switch

7
Español
Nota: La imagen puede diferir del producto actual.
Topología de la Red
Una Topología de la Red típica para el EAP se muestra a continuación.
EAP Controller
Se requiere un servidor DHCP (típicamente un router) para asignar las direcciones
IP a los EAPs y a los clientes en su red local. Una computadora que ejecute el
software del Controlador EAP, la cual puede estar la misma o en diferente subred
con los EAPs, se usa para manejar de manera central los EAPs.
Puede obtener el software del Controlador del EAP desde nuestro sitio web
http://www.tp-link.com.
Instalación del Equipo
■Opción 1: Montaje de la base en techo
Siga los pasos que se muestran a continuación para instalar el EAP con los
accesorios suministrados:
1Coloque la base en T para techo y empuje la
parte movible hacia la base del carril.
Sujeta la base T
para techo
Tornillos de cabeza plana M3×6
(Cantidad 5)
Host del
Controlador
Router Switch
Internet
Clientes
EAP
EAP
EAP

8
Español
2Use un tornillo de cabeza plana M3×6 para fijar
el sujeta-carril en T sobre el carril del techo.
3Fije el soporte de montaje al sujeta-carril en T
para techo usando cuatro tornillos de cabeza
plana M3x6.
4Fije el EAP al soporte de montaje alineando la
FLECHA 1 (en el EAP) con la FLECHA 2 (en el
soporte de montaje), después rotar el EAP en
sentido de las manecillas del reloj hasta que se
fije en su lugar.
5Conecte el cable de red al puerto ETHERNET.