TrailFX FCLR006W User manual

www.TrailFX.com
Page 1 of 4 Rev 112718
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT.
READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
DO NOT OVER TORQUE.STANDARD OPERATING LOAD FOR TIGHTEN
BODY MOUNT NUTS & BOLTS VARIES FROM 45 TO 65 FOOT POUND.
60-180 min
[e-mail]
1 866 638 4870
POLISHED STAINLESS STEEL –LIMITED LIFETIME
POWDER COATED BLACK –3 YEARS
Cutting Not
Required
First of all, please check what model you have bought. Part lists for 1 bar model are different. Please
find the related part list from below:
PARTS LIST for 1 Bars Model:
Qty
Part Description
Qty
Part Description
1
Main Cross Bar (female)
4
10-1.5mm x 35mm Carriage Bolts
1
Slide In Adjustable Cross Bar (male)
1
10-1.5mm x 20mm Hex Locking Bolts
2
Clamping Plates
4
10mm x 30mm OD x 2.5mm Flat Washers
1
U-Bolt Ladder Positioner
6
10mm Lock Washers
1
2-hole Clamp Plates
6
10mm Hex Nuts
LADDER RACK
Part No. FCLR006W
Fits : Universal Crossbar Ladder Rack
Clamp-On For Models With Rain Gutter
(2) Main Cross Bars (female)
(2) Slide-in Cross Bars
(male)
(2) U-Bolt
Positioners
(2) 2-hole Clamp
Plates
Drilling Not
Required

www.TrailFX.com
Page 2 of 4 Rev 112718
PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
AND WARNING ON PAGE 2 CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS
RECOMMENDED.
2. Select (1) Inner Cross Bar and (1) Clamp Plate, (Figure 1). Attach the Clamp Plate to the outside of the
upright on the Cross Bar with the included (2) 10mm x 35mm Carriage Bolts, (2) 10mm Flat Washers,
(2) 10mm Lock Washers and (2) 10mm Hex Nuts. Leave hardware loose at this time.
3. Repeat Step 2 to assemble all (5) remaining Cross Bar inner and outer assemblies.
4. Select (1) inner and (1) outer Cross Bar assembly. Slide (1) Inner Cross Bar into (1) Outer Cross Bar,
(Figure 2). Lock in place with (1) 10mm Hex Bolt, (Figure 3). Do not tighten locking bolt at this time.
5. Measure the width of the vehicle, rain gutter to rain gutter and transfer that measurement onto the
complete Cross Bar assembly.
6. With assistance, place the Cross Bar assembly into the desired position at the front of the vehicle.
NOTE: Install Cross Bars with the Outer Cross Bar toward the curb or right side of the vehicle. Snug
but do not fully tighten all hardware at this time.
7. Repeat Step 4—6to install the remaining Cross Bar assemblies towards the center and rear of the
vehicle.
8. Select (1) Load Positioner U-Bolt and (1) 2-Hole Clamp Plate, (Figure 4). Slide the U-Bolt down and
over the Outer Cross Bar. Secure the Positioner to the Cross Bar tube with the 2-Hole Lock Plate, (2)
10mm Flat Washers, (2) 10mm Lock Washers and (2) 10mm Hex Nuts. Adjust Load Positioner location
and tighten hardware. Repeat this Step for the remaining (2) Cross Bar assemblies.
9. Verify that the Cross Bar assemblies are straight and square on the vehicle and fully tighten all
hardware.
10. Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, wax this product after installing. Regular waxing is recommended to add a protective layer
over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap
may be used to clean the Ladder Rack.
(2) 10mm x 35mm
Carriage Bolts
(2) 10mm Flat Washers
(2) 10mm Lock Washer
(2) 10mm Hex Nuts
Fig 1
(Fig 2) Slide Adjustable side of
Cross Bar into Main Crossbar

www.TrailFX.com
Page 3 of 4 Rev 112718
Read and understand all WARNINGS and INSTRUCTIONS before assembly and installation.
Ladder Rack has a maximum static load capacity of 600lbs. when properly installed and the load distributed
evenly between two complete units. Load capacity is greatly affected by the design, strength and capacity of
the vehicle, intended load and must be determined by installer/user.
Ladders must be secured per ANSI standard A14.2-1990 paragraph 8.4.4.
This product is primarily intended for transporting ladders. It can be used for transporting lumber, pipe and
other similar materials when properly tied down and not exceeding capacity of the ladder rack or more
importantly, the vehicle. It is the responsibility of the user of this rack to safely secure these materials to the
rack before transporting. Any modifications made to this product for any other purpose other than its intended
use could create a hazardous condition that can cause serious personal injury or property damage.
Any modification or unintended use of this product shall immediately void all manufacturer's warranties.
Manufacturer disclaims all liability for injuries to persons or property resulting from any modification to or
unintended use of this product.
Stop Bolt
U-Bolt
2-Hole Clamp Plate
(2) 10mm Flat Washers
(2) 10mm Lock Washer
(2) 10mm Hex Nuts
Fig 4
Fig 3

www.TrailFX.com
Page 4 of 4 Rev 112718
FAQ’s
1. Hardware’s are not of correct size.
In GMC / Chevrolet truck model 2006 & up, customer needs to reuse the factory body bolts to install the bracket. If your vehicle is not
GMC / Chevrolet 2006 & up, ensure that holes are not partially covered with any plastic grommet or rust? If it is, remove the plastic
grommet & rust from the thread holes & re-try the installation.
2. Mounting Bracket are not getting Installed properly.
In some cases Illustration images shown in Installation manual may not be the exactly same as per actual vehicle images ,also if Driver /
Passenger side mounting brackets are very identical in the design, suggest referring Parts Identification guide to avoid fitment issue.
3. Products are thumping / rattling after installation.
Ensure that all required mounting brackets / hardware’s are installed & tighten correctly. Suggest using white lithium / regular grease
between the metal to metal contact surfaces.
4. Side Bar is not aligning with vehicle / Step Pads are not aligning with vehicle doors.
Side bar may be interchanged or mounting brackets are not installed at the correct position in the vehicle. Refer Parts identification guide.
5. Missing / Excess Hardware.
Recheck hardware count as per the part list.
6. Product not installing properly.
Ensure make model year, cab length and bed size of your vehicle is listed in the application. All installation steps are followed correctly.
No.
Parts Identification
1
Passenger / Right „Rear‟ Bracket marked “PR”
2
Driver / Left „Rear‟ Bracket marked “DR”
3
Passenger / Right „Center‟ Bracket marked “PC”
4
Driver / Left „Center‟ Bracket marked “DC”
5
Passenger / Right „Front‟ Bracket marked “PF”
6
Driver / Left „Front‟ Bracket marked “DF”
Note:
This guide is to identify the parts and not a reference for part count.
For part count, refer Parts List.
Product / Bracket image is representative and actual design may vary.
Check out these other TrailFX Products!! www.TrailFX.com
PRODUCT CARE
Periodically check the product to ensure all fasteners are tight and components are intact.
Regular waxing is recommended to protect the finish of the product.
Use ONLY Non-Abrasive automotive wax. Use of any soap, polish or wax that contains an abrasive is detrimental and can scratch the
finish leading to corrosion.
Aluminum polish may be used to polish small scratches and scuffs for Stainless Steel finish.
Mild soap may be used to clean the product for both Stainless Steel and Black finish.
Keystone Automotive Operations Inc. (KAO) warrants this product to be free of defects in material and workmanship at the time of purchase by the
original retail consumer. KAO disclaims any other warranties, express or implied, including the warranty of fitness for a particular purpose or an
intended use. If the product is found to be defective, KAO may replace or repair the product at our option, when the product is returned prepaid,
with proof of purchase. Alteration to, improper installation, or misuse of this product voids the warranty. KAO’s liability is limited to repair or
replacement of products found to be defective, and specifically excludes liability for any incidental or consequential loss or damage.