Tramigo T22 User manual

T22/T22i Installation Guide
© 2007 - 2011 Tramigo Ltd. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form
without the prior written permission of Tramigo.
Tramigo T22/T22i
Installation Guide
V1.54.4

T22/T22i Installation Guide
© 2007 - 2011 Tramigo Ltd. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form
without the prior written permission of Tramigo. Page 2
Contents
1Preface............................................................................................ 3
2Installation...................................................................................... 4
2.1 Installer Tools..........................................................................................5
2.2 Installation Site .......................................................................................5
2.3 Recommended Installation Sequence.....................................................6
2.4 Plan...........................................................................................................6
2.5 Connect ....................................................................................................7
2.5.1 Before fitting the SIM card......................................................................7
2.5.2 Fitting the SIM card ...............................................................................7
2.5.3 Mounting the T22..................................................................................8
2.5.4 T22 Wiring and Connections...................................................................9
2.5.5 Power and Ignition Sensing connection.................................................. 10
2.5.6 Personal Assistance Button or T22-ATB..................................................11
2.5.7 Sensor wiring ...................................................................................... 11
2.5.8 GPS External Antenna Option................................................................11
2.6 Configure................................................................................................12
2.7 Configuration Steps ...............................................................................13
2.8 Test.........................................................................................................15
2.9 Mount .....................................................................................................16
3Wiring Diagram ............................................................................. 18
3.1 Ignition / SOS Wiring ............................................................................19
3.2 ATB wiring..............................................................................................20
3.3 H20 Wiring .............................................................................................20
3.4 T22-CAR 24v Voltage protection...........................................................21
4T22 Spare Parts & Order Numbers................................................. 22
5Troubleshooting ............................................................................ 24

T22/T22i Installation Guide
© 2007 - 2011 Tramigo Ltd. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form
without the prior written permission of Tramigo. Page 3
1Preface
Failure to comply with the following warnings and safety information may
invalidate warranty, certification or type approval of this product.
This equipment should not be operated in hazardous environments i.e. areas that contain
explosive materials or flammable vapours.
This equipment should not be operated in aircraft or in close proximity to medical equipment.
Internal components containing beryllium oxide may be used in this equipment. Dust from this
material is a health hazard if inhaled or allowed to come into contact with the skin. Great care
must be taken when handling these components.
Unauthorised modification to this equipment or associated accessories is forbidden without the
express permission and agreement from the product manufacturer.
Safety Information
Please adhere to the following Safety and Installation information at all times.
Supply Voltage: +6V minimum to +32V maximum
Fuses : Power – fit a 1A inline fuse (included in T22-CAR)
Ignition – fit a 1A inline fuse.
Note: Fuses should be placed in all power lines and as close as possible to the vehicle supply
source.
THE RATINGS OF THESE FUSES SHOULD NOT BE EXCEEDED AT ANY TIME
WARNING!
This equipment may only be located in a position where it cannot interfere with
the normal operation of the vehicle or present a hazard to the driver or
passengers. Care must also be taken in the routing of all cables so that the
insulation does not become worn or damaged.
Installation Information
All installation and service work must be carried out in accordance with MPT 1362, MPT 1372,
RQAS, VSIB, 95/54/EC, ISO 21609 and / or any other statutory guidelines or Directives currently
in force.
Therefore it is strongly recommended that the T22 unit is installed and commissioned by suitably
trained and qualified Installation Personnel i.e. in the UK those who are accredited and registered
by the Vehicle Systems Installation Board (www.vsib.co.uk).
Important Notes!
Unauthorised changes or alterations to the equipment or the installation will invalidate
certification issued by the Approved Accreditation Body and may also affect the vehicle
manufacturers warranty.
Under no circumstances may any part of the T22 system be installed inside the engine
compartment area.

T22/T22i Installation Guide
© 2007 - 2011 Tramigo Ltd. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form
without the prior written permission of Tramigo. Page 4
2Installation
Before you begin installing and configuring the system please ensure that you have read this
manual thoroughly, referring to any supplementary information provided for the T22 unit and
user options as required.
The T22 installation kit is available as Automotive, Marine and Motorcycle version. For using extra
input you need T22i and T22-IO5 cable. The T22 version can be seen in unit label or by using the
VERSION command.
This document covers the T22/T22i unit and its connections:
•Power lead connection
•Installation Case
•Optional External GPS Antenna
•Optional IO Cable and Personal Assistance button
Figure 1 - T22 and Automotive Installation Kit
Important Notes!
When using the T22 platform you should remember the following:
In order for GPS to function correctly, the GPS antenna must have a clear view of the sky in
order to receive data from the satellites. Should this view be obscured, e.g. the vehicle is parked
in a metal-clad building then the performance of the T22 platform may be impeded. Wherever
possible it is preferable to park the vehicle in a location where the antenna will have a clear all
round view of the sky.
Charge the battery overnight before using your T22 for the first time.

T22/T22i Installation Guide
© 2007 - 2011 Tramigo Ltd. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form
without the prior written permission of Tramigo. Page 5
2.1 Installer Tools
The following tools are recommended for Tramigo T22 installs and are available at any car repair
location (except for mobile phone and GPS receiver):
1. Automotive screwdrivers, spanners, socket sets
2. 1 amp in line fuses (for ignition sensing connection)
3. Wire cutter, pliers, small saw
4. Voltage Meter
5. Automotive Electrical Tape (regular electrical tape will unwrap in 6 months)
6. Waterproof and heat resistant Automotive 2 way tape (3M has a good tape that is used
to secure trim on the vehicle exterior)
7. Foam tape – for preventing rattles
8. Small Ty-Wraps (for securing wires and case)
9. Power Drill Kit, 12 mm bit, cone cutter
10. Portable soldering Iron
11. Flashlight
12. Alcohol and cloth
13. Spare T22/T22i unit and accessories (in case of component failure)
14. Tramigo T22 wiring diagrams (included in this document)
15. Wire connectors and crimping tool or Posi-Lock wire connectors – www.posi-lock.com
16. GSM Phone or PC (for configuration)
17. Portable GPS receiver (for testing GPS signal strength). Any unit will work as long at it
shows the GPS signal strength.
2.2 Installation Site
The installation can be performed in any well ventilated and well lit area as found in a car
dealership or accessory installation bay. There is no requirement to raise the vehicle. To obtain
the first GPS lock a clear view of the sky is required, which should be considered if designing a
custom install center. A GPS repeater can be used to obtain a signal inside a building.
Care should be taken to avoid scratching the vehicle during the installation process. Protective
clothing and vehicle covers should be used.
Installations are also performed on the customers home or office site, so a portable install toolkit
is required.

T22/T22i Installation Guide
© 2007 - 2011 Tramigo Ltd. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form
without the prior written permission of Tramigo. Page 6
2.3 Recommended Installation Sequence
The following installation sequence is recommended. Please refer to the instructions elsewhere in
this document for further details.
1. Plan the whole installation and determine suitable locations, mounting arrangements
and cable routes for all hardware items.
2. Connect Fit SIM card. Temporarily mount the main T22 unit and temporarily connect all
wiring, while still able to see the status lights on the unit
3. Configure the unit
4. Test that all hardware features are working
5. Mount Complete the permanent installation and wiring
oPerform final test of T22 functions.
oTest that all vehicle buttons and switches still work.
2.4 Plan
Plan your complete installation first to avoid re-wiring later. T22i has one output (slots 1 and 2 in
the T22-IO5 cable) and two inputs (slots 3 and 5, 4 and 5).
NOTE: T22-H and previous models have only 1 input (slot 3 and 4).
For the T22i input you can choose 1 or 2 of:
1. Personal Assistance Button/ATB (or/and)
2. Ignition Sensing
For T22 input you can only choose only 1 from below options:
1. Personal Assistance Button/ATB or
2. Ignition Sensing
The output can be used to immobilize the starter circuit. Contact [e-mail] for
instructions.
Unit Location
Your T22 unit can be mounted anywhere inside your vehicle or boat where the unit will not get
wet. The most common locations are behind the dashboard, under the centre console, and
under a side panel in the back of the vehicle. Pick a location where you can secure the unit
firmly to prevent any rattling sounds after installation.
The motion detector works best if the unit is as flat as possible.

T22/T22i Installation Guide
© 2007 - 2011 Tramigo Ltd. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form
without the prior written permission of Tramigo. Page 7
Antenna Location
In order for GPS to function correctly, the GPS antenna must have a clear view of the sky in
order to receive data from the satellites. Should this view be obscured, e.g. the vehicle is parked
in a metal-clad building then the performance of the T22 platform may be impeded. Wherever
possible it is preferable to park the vehicle in a location where the antenna will have a clear all
round view of the sky at installation time to test the signal strength.
The antenna and wires can be hidden from view but the installer.
Common locations are:
•Under the dashboard as far to the front of the vehicle as possible
•Under the plastic cover near the windshield wipers
•Under the plastic cover of the front or rear bumpers
•In the license plate lamp (on SUV types)
•In the side mirrors (when space permits)
Personal Assistance Button Location
It is recommended that the Personal Assistance Button, where fitted, is located within easy reach
and visibility of the vehicle driver, or where required in a covert location. Typically it will be fitted
into a blank switch position.
2.5 Connect
2.5.1 Before fitting the SIM card
•If you have not already registered your SIM card with the mobile network, you should do
this before proceeding. Please refer to the appropriate mobile network operator
instructions on how you do this.
•Check that the SIM card can send and receive SMS using a hand phone
•Ensure that the SIM card is not protected by a PIN number
•For prepaid accounts ensure there is sufficient load or credits to send SMS
•It is recommended to use a new SIM card to ensure good contact with the SIM reader
•Record the phone number of the SIM card
2.5.2 Fitting the SIM card
Important Note!
When inserting or removing the SIM card from the T22 it is necessary to take care:
•Before inserting or removing the card, remember to turn off the power or remove the
battery;
•Do not bend or scratch the card;
•The golden chip should be kept clean at all times;
•To prolong the life cycle of the card, avoid any unnecessary insertion or removal of the
card.

T22/T22i Installation Guide
© 2007 - 2011 Tramigo Ltd. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form
without the prior written permission of Tramigo. Page 8
2.5.3 Mounting the T22
After checking that all the functions are working you are ready to permanently mount your unit.
T22 Installation Case
1. Attach the wiring to the T22 and insert in the installation case. If using the Rugged case
you will need to cut the soft rubber to allow access for the cables. Just make a very
small slit and push the cable through the rubber. You can also seal the cable with silicon
if needed.
After checking that all the functions are working you are ready to permanently mount your unit.
Your T22 unit can be mounted anywhere inside your vehicle or boat where the unit will not get
wet. The most common locations are behind the dashboard, under the centre console, and
under a side panel in the back of the vehicle. Pick a location where you can secure the unit
firmly to prevent any rattling sounds after installation.
Figure 2 - T22 Wiring Connected
T22 Automotive Installation Case
1. Attach the wiring to the T22 (see Figure 2)
a. Personal Assistance Button connects to slots 3 and 5 in the T22 IO5 Cable
b. Ignition sensor* connects to slots 4 and 5 in the T22 IO5 cable
2. Feed all the T22 wires through the C slot, with the largest wire (power connection)
placed last and on top. (see Figure 3)
3. Pull on the wires gently to remove any slack inside the C slot.
4. Attach the case cover to secure the wires in place.
Note: you can use electrical tape to hold the wires in the C slot until the case
cover is attached.
5. Optionally you can use electrical tape to seal the slot where the wires exit the Case.
6. Ty-wraps can be used to attach the case cover through the mounting holes.
7. 2-way tape can be used to attach the case to the vehicle
*Optional and pertains to devices/equipments with 4V higher input

T22/T22i Installation Guide
© 2007 - 2011 Tramigo Ltd. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form
without the prior written permission of Tramigo. Page 9
Figure 3 - T22 Automotive Installation Case
2.5.4 T22 Wiring and Connections
Important Notes!
Unauthorized changes or alterations to the equipment or the installation will invalidate
certification issued by the Approved Accreditation Body and could also affect the vehicle
manufacturer’s warranty. If in doubt only connect T22 to the vehicle power.
All wiring should be safely secured to avoid damage from, or chaffing by, any hot or moving
parts.
Position wiring carefully to avoid the possibility of snagging or impact damage during the normal
use of the vehicle.
Before any holes are drilled, check that no parts, wires, pipes or tanks could be damaged at the
other side of the hole. Suitable grommets must be used where wires are routed through body
panels to prevent short circuits to the chassis.
Leave in-line fuses out of holders until the installation is complete.
Cable Assemblies
The T22 has one main power cable, an IO cable for ignition sensing, or external personal
assistance button.
When you configure the T22 you will be able to carry out tests to determine whether suitable
GSM and GPS signals are being received. If in doubt about the suitability of your planned
location, it is recommended that you only temporarily install until you are able to carry out the
appropriate configuration tests.

T22/T22i Installation Guide
© 2007 - 2011 Tramigo Ltd. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form
without the prior written permission of Tramigo. Page 10
2.5.4.1 Identifying IO ports on your T22-IO cable
Connect your T22-IO to your T22. Then lay them on a flat surface.
Make sure the T22-IO does not twist and is parallel to the surface.
T22-IO5 T22-IO
After identifying the T22-IO Pins, follow the rest of the installation guide
2.5.5 Power and Ignition Sensing connection
T22-CAR cable is used to connect to permanent vehicle power in the fuse box or directly to the
car battery. In large 24V vehicles a 30 ohms, 10 watts resistor is required for protection.
Wire Colour Description Notes
Red Vehicle Supply Positive (+ve) Connect to a permanent Positive supply
(6 to 24V) via a 1 amp in-line fuse.
Black Vehicle Supply Negative (-ve) Connect to permanent Negative.
T22-IO cable is required for ignition sensing.
Wire Colour Description Notes
Blue Ignition Sense Positive (+ve)
switched (active high) Connect Slot 4 in the T22-IO5 cable to switched ignition line via a 1 amp in-line
fuse
Black Ground Connect Slot 5 in the T22-IO5 cable to
vehicle ground
•PIN 1 is beside the USB port
•PIN 5 is beside the microphone
jack (for T22i)
•PIN 4 is beside the microphone
jack (for T22)

T22/T22i Installation Guide
© 2007 - 2011 Tramigo Ltd. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form
without the prior written permission of Tramigo. Page 11
2.5.6 Personal Assistance Button or T22-ATB
Connect the 2 wires from the Personal Assistance Button to the T22-IO5/IO cable.
(T22i) slots 3 and 5
(T22) slots 3 and 4
Note the personal assistance button can also be used to trigger the phone button in situations
where a 3rd party hands free kit (in-car speaker and microphone) is attached to the T22.
2.5.7 Sensor wiring
Connect the 2 wires from the Sensor to the T22-IO5/IO cable.
(T22i) slots 3 and 5
(T22) slots 3 and 4
This is the same as when connecting the SOS/ATB or Ignition input.
Any sensor that has an analogue circuit can be used.
NOTE:
When using T22i Slot 3 and 5 Do take note that the maximum voltage for that
input is ~4V. When wiring a higher Voltage accessory use slot 4 and 5 ( When
ignition not in use)
2.5.8 GPS External Antenna Option
This option is needed when it is not possible to install the T22 in a location where the GPS
antenna will work. This option allows the antennas to be located in a different location within the
vehicle.
The GPS antenna should be positioned horizontally and located in a position where it will have an
unobstructed view of the sky. The ideal location in most cars is in the centre top of the
dashboard, it may also be possible to locate the antenna on the underside of the dashboard,
however, it is important to ascertain that there are no conductive materials present in the
construction of the dashboard prior to fitting the antenna.
The GPS antenna must have the black side facing toward the sky. The flat side with the magnet
faces to the ground.
Important Note!
The performance of the equipment may be impeded if the antenna is mounted
beneath or in very close proximity to electrically conductive materials, such as metal,
certain types of plastic, metalled film or laminate (tinted) windscreens. If this applies
to your vehicle please install the antenna elsewhere.

T22/T22i Installation Guide
© 2007 - 2011 Tramigo Ltd. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form
without the prior written permission of Tramigo. Page 12
2.6 Configure
After completion of the Installation as described in Section 2, you are ready to configure your
T22.
Figure 4 - T22 Control Panel
Your T22 has 3 lights to indicate the status of the unit. Green means ok and red means that
you have a problem. T22 buttons require you to press for 2 seconds to prevent accidental
triggering.
Power LED - Green:
Flashing (5 seconds) Power is on
On Charging
Off Power is off or T22 is sleeping
GSM LED – Red:
On T22 is not connected to the GSM network
Off T22 is connected to the GSM network
Flashing T22 is having problems sending a SMS.
GPS LED - Red:
On T22 does not have a GPS fix
Off T22 has a GPS fix
Power Button Press for 2 seconds to activate
Personal Assistance Button Press for 2 seconds to activate.
When using an external SOS/ATB button the T22 be configured to arm the Alarm by
pressing less than 5 seconds. Or the external SOS/ATB can also be used to activate the
phone functions.
Phone Button Press once to answer incoming call
Press for 2 seconds or more to initiate an outgoing call to
User 1, press a second time for User 2, etc. Second and
third press does not have to be 2 seconds.
Incoming call is indicated by the GSM and GPS lights flashing
together.
Remote Assistance Button Press for 5 seconds or more to activate Assistance message.
Press for 0.2 to 1.9 seconds to use as phone button. Second
press must be within 1 second to dial 2nd speed dial number.

T22/T22i Installation Guide
© 2007 - 2011 Tramigo Ltd. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form
without the prior written permission of Tramigo. Page 13
2.7 Configuration Steps
•Check that the green Power light on solid (charging) or emitting a short flash every 5
seconds.
•Check that the red GSM light is off.
•Read the instructions in the T22 User Manual.
•Send the following SMS to your T22 in upper or lower case from the Owner’s phone
if possible: OWNER,0000
Note: four zeros is the default password
•T22 will respond with a text message stating:
Tramigo: Owner, [phone] registered
•This means that you are now the Owner of T22 and it will accept any commands that
you issue to it, providing they come from the same mobile phone number as you
used for this setup.
oIf the Owner’s phone is not available you can add their number with the
Adduser command:
AU,phoneNum,OWNER
Note: The 2 step process is done to prevent errant SPAM messaging from interfering
with the registration of your unit.
•If you have Ignition Sensing connected then you need to issue the following
commands
T22i commands:
oset,IgnitionInputGPIO,1
oset,IgnitionInputShock,0
oset,SOSGPIO,0
oset,input1,4
oset,SensorInputGPIO,0
oyou can also load the T22 - IGNITION+ SENSOR v1.54.0.CF** file
using Tramigo Manager software instead of typing the commands
manually
T22 commands:
oset,IgnitionInputGPIO,1
oset,IgnitionInputShock,0
oset,SOSGPIO,0
oset,SOSMinPressTime,0
oset,SensorInputGPIO,0
oyou can also load the T22 - Ignition v1.40.CF* file using Tramigo
Manager software instead of typing the commands manually
In Tramigo manager * v1.40 CF; **v1.54 CF

T22/T22i Installation Guide
© 2007 - 2011 Tramigo Ltd. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form
without the prior written permission of Tramigo. Page 14
•If you have the T22-SOS/ATB connected then you need to send the following
commands to the unit:
T22i commands:
oset,input2,1
oset,SOSMinPressTime,2000
oYou can also load the T22 - Install - SOS v1.54.0.CF** file using
Tramigo Manager Software instead of typing the commands manually.
T22 commands:
oset,IgnitionInputGPIO,0
oset,IgnitionInputShock,1
oset,SOSGPIO,1
oset,SOSMinPressTime,2000
oset,SensorInputGPIO,0
oYou can also load the T22 - SOS v1.40.CF* file using Tramigo Manager
software instead of typing the commands manually.
•If you want to use the SOS button to arm the Alarm, then send this command with
the other SOS config commands
T22i commands:
oSet,AlarmConfirmation,0
oSet,AlarmButton,1
oSet,AlarmAuto,6
oset,PanicButtonHoldTime,5
oset,input2,2
oYou can also load the T22 - Bike ATB Arming Config v1.54.0.CF(**)
file using Tramigo Manager Software instead of typing the commands
manually.
T22 commands:
oSet,SosNoHFGPIO
oYou can also load the T22 - Alarm SOS v1.40.CF* file using Tramigo
Manager Software instead of typing the commands manually.
•If you have the T22-H20 or some other sensor connected then you need to send the
following commands to the unit:
T22i commands:
oset,input2,3
oset,SensorON,1
oset,SensorOFF,1
oyou can also load the T22 - SENSOR v1.54.0.CF** file using Tramigo
Manager software instead of typing the commands manually.
T22 commands:
oset,IgnitionInputGPIO,0
oset,IgnitionInputShock,1
oset,SOSGPIO,0
oset,SensorInputGPIO,1
oset,SensorON,1
oset,SensorOFF,1
oyou can also load the T22 - Sensor Config v1.40.CF* file using
Tramigo Manager software instead of typing the commands manually.
In Tramigo manager * v1.40 CF; ** v1.54 CF
; (**) v1.54 CF applicable also to car use

T22/T22i Installation Guide
© 2007 - 2011 Tramigo Ltd. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form
without the prior written permission of Tramigo. Page 15
•If you have the T22-ATB connected then you need to send the following commands
to the unit:
T22i commands:
oSet,AlarmConfirmation,0
oSet,AlarmButton,1
oSet,AlarmAuto,6
oset,PanicButtonHoldTime,2
oset,input2,1
oYou can also load the T22 - ATB v1.54.0.CF** file using Tramigo
Manager Software instead of typing the commands manually.
T22 commands:
oset,IgnitionInputGPIO,0
oset,IgnitionInputShock,1
oset,SOSGPIO,1
oset,SensorInputGPIO,1
oset,SOSMinPressTime,2000
oYou can also load the T22 - SOS v1.40.CF* file using Tramigo Manager
software instead of typing the commands manually.
•Also available are configuration files for other uses such as Bike, Boat and Caravan.
2.8 Test
Test all the wiring connections and GPS Antenna.
•Check the GPS antenna by moving the vehicle to a location with a clear view of the
sky. When the red GPS light goes off (1-3 minutes) send a FIND command to check
the location.
•If Ignition sensing is connected test by
oTurning on Ignition reporting
I or I,ON
oTurn on and off the ignition and you should receive 2 SMS
•Test the external SOS button by pressing for 2 seconds. You should receive a SMS
from the unit.
•If auto arming is activated then test the auto arming of the Alarm by pressing the
SOS button by pressing for less than 2 seconds.
oSend A,ON
oPress the SOS button – the alarm will activate in 30 seconds
oShake unit – you should receive Motion Alarm
•If the Sensor s connected test by
oTurning on Sensor reporting
SE or SE,ON
oActivate and deactivate the sensor
In Tramigo manager * v1.40 CF; **v1.54 CF

T22/T22i Installation Guide
© 2007 - 2011 Tramigo Ltd. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form
without the prior written permission of Tramigo. Page 16
Mount
The T22 Automotive installation case has 2 covers that you can use to cover the LED panel.
Place the cover inside the case to cover the hole that provides access to the T22 control panel
then place the T22 base unit on top. The base unit will hold the plastic cover in place, or
optionally you can use 0.5mm 2-way tape to secure the cover
1. The black cover is used for installations where you want the control panel hidden so that
the unit is not noticed during future vehicle maintenance, or by car thieves.
2. The clear cover is used for installations where the control panel is visible, and adds extra
protection.
There are 2 primary methods of mounting the T22 unit:
1. Use the 4 screw holes to attach to a flat surface inside the vehicle. Use self drilling sheet-
metal screws, diameter max ST 4,2 mm, length about 20mm, cross recessed, pan head.
The T22 Rugged case can be mounted with 2-way tape.
2. Use 2 TY-wraps to secure the 2 parts of the installation case, then use double-sided
automotive grade tape to attach the case to the vehicle.
You may choose to mount the T22 somewhere covertly e.g. under the dashboard, but in all
cases the T22 GPS antenna must be placed such that sufficient “view of the sky” is available to
the T22 to allow for GPS signal reception from the orbiting GPS satellites and cellular radio
communications with the mobile radio network. These radio signals do not pass through metal or
electrically conductive material.
In general, you can expect that a mounting situation under the dashboard of a vehicle will be
satisfactory.
Check your windscreen: Should the windscreen be provided with heating that uses a metal
film or fine wires built into the windscreen, or features a special heat reflecting athermic layer,
then the GPS signal from the orbiting satellites will be screened from the T22.
The T22 should then be mounted at the side of the windscreen where there is sometimes a
special zone free of the metallization.
If this does not work, then you can locate the external GPS antenna under the windshield wipers,
front or rear bumpers, or any location where only plastic covers the antenna. If you need to run
the GPS antenna cable through the engine compartment use a standard plastic automotive grade
shrouding to protect the cable.

T22/T22i Installation Guide
© 2007 - 2011 Tramigo Ltd. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form
without the prior written permission of Tramigo. Page 17
Window Tinting
GPS signals are blocked by metal surfaces which can include some brands of window film that
contain metal particles. To ensure that GPS, cell phone, smart tag, and radio reception is not
impacted either:
1. Use a non-metallic tint
2. Avoid tinting the front windshield where the T22 unit is located (World wide legislative
trend is to ban windshield tinting due to increased risk of accidents)
3. Leave a 15 cm gap at the bottom of the windshield and place the T22 by this opening.
This still provides security for vehicle occupants.
4. Use the External GPS Antenna and locate the GPS antenna under the front bumper or
under the windshield wipers – as long as the antenna is not covered by metal.
The list of good quality non-metallic film includes the 3M film, Madico CharcOOl (not Madico
CharcOAl), Huper Optik Ceramic (Stark), and FormulaOne Pinnacle (ceramic film). Costs for good
quality metallic film is similar to non-metallic film.
WARNINGS:
•Your T22 must be securely mounted in a location where it cannot interfere
with the normal operation of the vehicle. It must not be located in a
position where the cables or the T22 Unit may become a hazard to the
driver or any passengers.
•Under no circumstances may any part of the T22 system be installed inside
the engine compartment area. (except the GPS antenna cable)

T22/T22i Installation Guide
© 2007 - 2011 Tramigo Ltd. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form
without the prior written permission of Tramigo. Page 18
3Wiring Diagram
Figure 5: T22 Car+Ignition Sensing Diagram

T22/T22i Installation Guide
© 2007 - 2011 Tramigo Ltd. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form
without the prior written permission of Tramigo. Page 19
3.1 Ignition / SOS Wiring

T22/T22i Installation Guide
© 2007 - 2011 Tramigo Ltd. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form
without the prior written permission of Tramigo. Page 20
3.2 ATB wiring
3.3 H20 Wiring