Travis Industries 36 CF ST User manual

36 CF ST / Pier
Fireplace
• Operation
• Maintenance
Tested and Listed by
OMNI-Test Laboratories, Inc.
Beaverton, Oregon
Report # 028- -87-5
ANSI Z21.88a-2007
WARNING: If the information in the e in truction i not followed exactly, a fire or
explo ion may re ult cau ing property damage, per onal injury or lo of
life.
- Do not tore or u e ga oline or other flammable vapor and liquid in the vicinity of thi
or any other appliance.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical witch; do not u e any phone in your building.
• Immediately call ga upplier from a neighbor' phone. Follow the ga upplier'
in truction .
• If you cannot reach your ga upplier, call the fire department.
- In tallation and ervice mu t be performed by a qualified in taller, ervice agency or
the ga upplier.
Thi appliance may be in talled in an aftermarket permanently located, manufactured home (USA
only) or mobile home, where not prohibited by local code .
Thi appliance i only for u e with the type( ) of ga indicated on the rating plate. A conver ion kit i
upplied with the appliance.
Owner' Manual
 Copyright 2009, T.I. $10.00 100-01213_000 4090202 4800 Harbour Pointe Blvd. SW
Mukilteo, WA 98275

2 Introduction
© Travis Industries 4090202 100-01213_000
Introduction
We welcome you as a new owner of a 36 C ST (See Through) / Pier gas fireplace. This manual
details operation and maintenance of this fireplace. Please familiarize yourself with the Owner's
Manual before operating your heater and save the manual for future reference.
Important Information
No other 36 C ST / Pier gas fireplace has the same
serial number as yours. The serial number is on the
listing label that is chained to the gas control valve.
This serial number may be needed in case you
require service.
Model: 36 C ST / Pier ireplace
Serial Number:
Purchase Date:
Purchased rom:
Regi ter your warranty online at:
travi warranty.com
Or, mail your warranty card to:
Travis Industries House of ire
4800 Harbour Pointe Blvd. SW
Mukilteo, WA 98275
Save Your Bill of Sale.
To receive full warranty coverage, you will
need to show evidence of the date you
purchased your heater. Do not mail your
Bill of Sale to us.
We suggest that you attach your Bill of
Sale to this page so that you will have all
the information you need in one place
should the need for service or information
occur.
Installation Warnings
• In tallation requirement are printed in the 36 CF ST / Pier In tallation Manual (part # 100-
01213). All requirement in the in tallation manual mu t be met.
• Failure to follow all of the requirement may re ult in property damage, bodily injury, or
even death.
• Thi heater mu t be in talled by a qualified in taller who ha gone through a training
program for the in tallation of direct vent ga appliance .
• Thi appliance mu t be in talled in accordance with all local code , if any; if not, follow
ANSI Z223.1 and NFPA 54(88).
• In Manufactured or Mobile Home mu t conform with Manufactured Home Con truction
and Safety Standard, Title 24 CFR, Part 3280, or, when uch a tandard i not applicable,
the Standard for Manufactured Home In tallation , ANSI/NCSBCS A225.1. Thi appliance
may be in talled in Manufactured Hou ing only after the home i ite located.
• The fireplace i de igned to operate on natural ga , or propane (LP).
• All exhau t ga e mu t be vented out ide the tructure of the living-area. Combu tion
air i drawn from out ide the living-area tructure.
• Notify your in urance company before hooking up thi fireplace.
• The ceramic fireback mu t be in talled in thi fireplace prior to operation.

Introduction 3
© Travis Industries 4090202 100-01213_000
Table of Contents
Introduction and Important Information
Introduction............................................................. 2
Important Information ...............................................2
Installation Warnings ................................................ 2
eatures................................................................. 3
Gas Input Specifications ........................................... 3
Safety Precaution
Safety Precautions...................................................4
Operation
Before You Begin..................................................... 6
Remote Control .......................................................6
Setting Up the Remote (Time, Day, Swing, °/°C) ........6
Remote Synchronization............................................ 8
The Two Modes of Operation ......................................8
Manual Mode ........................................................8
Thermostat Mode ..................................................8
Remote unctions....................................................10
Switching Between Remote unctions.......................10
MAIN UNCTION (Main Burner)..............................11
REAR UNCTION (Rear Burner – Not Used)...........11
AN UNCTION ( or optional power heat duct).........11
LIGHT UNCTION................................................11
AUX UNCTION ...................................................11
TIMER UNCTION................................................11
PROGRAM UNCTION (Programmable 7 day
thermostat) ..........................................................12
Starting the ireplace for the irst Time
Continuous Pilot – or Very Cold Conditions................13
Normal Operating Odors............................................13
Power Outages.........................................................13
Child Protection eature............................................13
Maintenance
Yearly Service Procedure.......................................... 14
Glass rame Removal and Installation........................ 15
Log Set Installation .................................................. 16
Battery Installation................................................... 19
Accent Light Bulb Replacement ................................. 20
Wiring Diagram........................................................ 21
Replacement Parts List ............................................ 21
Warranty
Warranty ................................................................ 22
Optional Equipment
Accessories............................................................ 23
Index
Index...................................................................... 24
Features
• Works During Power Outages
• Standard Remote Control with Thermostat
• Realistic "Wood ire" Look
• Convenient Operating Controls
• Variable-Rate Heat Output
• Low Maintenance
Gas Input Specifications
Natural Ga Propane
Maximum BTU Input Per Hour 58,000 58,000
Minimum BTU Input on Low 27,000 27,000

4 Safety Precaution
© Travis Industries 4090202 100-01213_000
IF YOU SMELL GAS:
* Do not light any appliance
* Extingui h any open flame
* Do not touch any electrical witch or plug or unplug anything
* Open window and vacate building
* Call ga upplier from neighbor' hou e, if not reached, call fire department
This unit must be installed b
y
a qualified installer to prevent the possibilit
y
of an
explosion. Your dealer will know the requirements in your area and can inform you
of those people considered qualified. The room heater should be inspected and
cleaned before use and at least annually by a qualified service person. More
frequent cleaning may be required due to excessive lint from carpeting, bedding
material, etc.
The instructions in this manual must be strictl
y
adhered to. Do not use makeshift
methods or compromise in the installation. Improper installation will void the
warrant
y
and safet
y
listin
g
.
CH 4
- or -
83H
C
This heater is either approved
for natural gas (NG) or for
propane (LP). Burning the
incorrect fuel will void the
warranty and safety listing and
may cause an extreme safety
hazard. Direct questions
about the type of fuel used to
your dealer or installer
Operate the heater accordin
g
to the instructions included in
this manual.
If the main burners do not start
correctly turn the gas off to the
fireplace and call your dealer
for service.
Ok
Contact
y
our local buildin
g
officials to obtain a permit and
information on any installation
restrictions or inspection
requirements in your area.
Notify your insurance
company of this heater as
well.
If the flame becomes soot
y
,
dark orange in color, or
extremely tall, do not operate
the heater. Call your dealer
and arrange for proper
servicing.
It is imperative that control
compartments, screens, or
circulating air passageways of
the heater be kept clean and
free of obstructions. These
areas provide the air necessary
for safe operation. ?Do not operate the heater if it is
not operating properly in any
fashion or if you are uncertain.
Call your dealer for a full
explanation of your heater and
what to expect.
Gas
Do not store or use
g
asoline or
other flammable liquids in the
vicinity of this heater.
AAAAA
AAAAA
AAAAA
AAAAA
AAAAA
AAAAA
AA
AA
Do not operate if an
y
portion of
the heater was submerged in
water or if an
y
corrosion occurs.
Immediately call a qualified
service technician to inspect
the appliance and to replace
any part of the control system
and any gas control that has
been under water.

Safety Precaution 5
© Travis Industries 4090202 100-01213_000
Do not place clothin
g
or other
flammable items on or near
the heater. Because this
heater can be controlled by a
thermostat there is a possibility
of the heater turning on and
igniting any items placed on
or near it.
AA
AA
AA
AA
A
Li
g
ht the heater usin
g
the built-
in electronic igniter. Do not
use matches or any other
external device to light your
heater.
Allow the heater to cool before
carrying out any maintenance
or cleaning.
The viewin
g
g
lass should be
opened only for conducting
service. Do not operate with
cracked, broken, or removed
glass.
An
y
safet
y
screen or
g
uard
removed for servicing must be
replaced prior to operating the
heater.
Never remove, replace, modify
or substitute any part of the
heater unless instructions are
given in this manual. All other
work must be done by a trained
technician. Don't modify or
replace orifices.
Prior to removing the glass,
shut off gas to the appliance
(or remove the batteries from
the battery box and shut off
electricity to the fireplace).
This prevents any chance of
accidental burner ignition
when accessing the firebox.
This
Manual
Do not throw this manual awa
y
.
This manual has important
operating and maintenance
instructions that you will need
at a later time. Always follow
the instructions in this manual.
AA
AA
AA
AA
This unit is not for use with
solid fuel
Do not place an
y
thin
g
inside
the firebox (except the
included fiber logs).
If the fiber lo
g
s become
damaged, replace with Travis
Industries log set.
Instruct ever
y
one in the house
how to shut gas off to the
appliance and at the gas main
shutoff valve. The gas main
shutoff valve is usually next to
the gas meter or propane tank
and requires a wrench to shut
off.
Children and adults should be
alerted to the hazards of high
surface temperature and
should stay away to avoid
burns or clothing ignition.
Young children should be
supervised when they are in
the same room as the heater.
Travi Indu trie , Inc.
g
rant
no warranty, implied or tated,
for the in tallation or
maintenance of your heater,
and a ume no
re pon ibility of any
con equential damage( ).
Operate the heater accordin
g
to the instructions included in
this manual.
If the main burners do not start
correctly turn the gas off to the
fireplace and call your dealer
for service.

6 Operation
© Travis Industries 4090202 100-01213_000
Before You Begin
Read this entire manual before you use your new fireplace (especially the section "Safety
Precautions" on pages 4 & 5). ailure to follow the instructions may result in property damage,
bodily injury, or even death.
Remote Control
The remote control controls all of the functions on the fireplace. It can be placed inside the
holder and hung on the wall or it can be placed near the fireplace.
Fn
Set
Mode
Setting Up the Remote (Time Day Swing ° F/ ° C)
The remote will need to be set up when first started or when the batteries were removed or
replaced. ollow the directions below to set the time, day, and other settings.
A. Press and hold the “Set” and “Up” arrow buttons for 5 seconds.
B. The “ROOM” temperature will blink. Use the arrow keys until ° (fahrenheit) or °C (celcius) is
displayed. Press the “Set” button to set the temperature scale.
C. The “SWING” number will blink. Use the arrow keys to select the desired swing amount (1, 2
or 3 °, 1 or 2 °C). The swing number determines the amount of degrees the thermostat will
wait until turning on. The larger the number, the less often the thermostat will turn on and
off. The smaller the number, the more often the thermostat will turn on and off.
D. The day of the week will blink. Use the arrow keys to select the correct day. Press the “Set”
button to set the day.
E. The hour of the day will blink. Use the arrow keys to select the correct hour. Press the “Set”
button to set the hour.
. The minute of the hour will blink. Use the arrow keys to select the correct minute. Press the
“Set” button to set the minute.
G. The AM / PM designation will blink. Use the arrow keys to select the correct setting. Press
the “Set” button to set AM / PM.

Operation 7
© Travis Industries 4090202 100-01213_000
Remote Synchronization
The remote control is shipped pre-synchronized to the fireplace. If, however, the remote does not
work with the fireplace, follow the directions below to synchronize the remote to the fireplace.
NOTE: The fireplace must have power and the transmitter must have batteries to complete this process.
WARNING: Shut the gas off to the fireplace prior to conducting this process.
1 The “Learn” switch is accessed by removing the remote holder. Inside the junction box behind the
holder you will find the “Learn” switch (see the illustration below).
2 Press the “Learn” button once. The fireplace will beep once.
3 Press the “Mode” button on the remote. The fireplace will beep five times to indicate
synchronization.
Fn
Set
Mode
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
Beep
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AAA
AAA
AAA
AAA
AAA
AA
AA
AA
AA
AA
AAA
AAA
AAA
AAA
AAA
AAA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
Beep, Beep,
Beep, Beep,
Beep
NOTE: Re- etting the Receiver Module
If the receiver module fails to synchronize with the remote after two attempts, you should re-set the
receiver module. To do this, hold down the LEARN button for approximately 10 seconds until the
receiver beeps 3 times. This indicates the receiver has been re-set and can be synchronized using
the instructions above.

8 Operation
© Travis Industries 4090202 100-01213_000
The Two Modes of Operation
Manual Mode
In manual mode you can turn the fireplace on and off by pressing the “Mode” button until “ON” or
“O ” appears on the remote.
Fn
Set
Mode
Fn
Set
Mode
Thermo tat Mode
While in thermostat mode, the remote will
monitor the temperature and turn the fireplace
on and off to meet the desired temperature.
To turn on Thermo tat Mode:
Press the “MODE” button on the remote until
“THERMO” appears on the LCD display.
To turn off Thermo tat Mode:
Press the “MODE” button on the remote until
“THERMO” no longer appears on the LCD
display (the fireplace will be ON or O , see
“Manual Mode” above.
Fn
Set
Mode

Operation 9
© Travis Industries 4090202 100-01213_000
Adju ting the Target Temperature of the Thermo tat:
Make sure the remote is in thermostat mode. Press the up and down arrow buttons until the
desired temperature is displayed in the “SET” box (see illustration below).
Fn
Set
Mode
WARNING: While in thermostat mode the fireplace will turn on and off to meet the temperature
demands of the remote. Do not place any items near the fireplace or conduct service without
shutting off gas to the fireplace.
WARNING: If the remote is set to a high temperature the fireplace may remain on for an extended
period of time. This may be a concern to those using LP (propane).
WARNING: If the remote is used as a thermostat for extended periods, make sure the batteries are
charged. We recommend replacing the batteries at the beginning of the heating season. If the
batteries go dead while in thermostat mode, the fireplace will shut off after 2 hours.

10 Operation
© Travis Industries 4090202 100-01213_000
Remote Functions
Switching Between Remote Function
By pressing the unction “ N” button, you can scroll through the following 7 functions on the
remote:
• MAIN (Main Burner)
This function will only appear when burner is on.
• REAR (Rear Burner – Not U ed)
• FAN
This function may be used when using an optional power heat duct.
• LIGHT
This function adjusts the build-in accent light.
• AUX (Not U ed)
• TIMER
This function allows the user to turn the fireplace on for a set period of time.
• PROGRAM (Programmable 7 day thermo tat)
This function allows the user to program specific on/off, temperature, weekday and weekend
settings on the thermostat.
or a complete description of each function, refer to the sections on the following pages for each
individual function.
Fn
Set
Mode

Operation 11
© Travis Industries 4090202 100-01213_000
MAIN FUNCTION (Main Burner)
The main burner flame height may be adjusted from low “1” to high “3”. Use the arrow keys to
adjust the setting. Once the desired setting is made, the remote will alter the setting after
approximately 8 seconds (and the remote display will stop blinking).
NOTE: The fireplace must be on (either manual or thermostat) to adjust the main burner.
REAR FUNCTION (Rear Burner – Not U ed)
This function is not used on this fireplace
FAN FUNCTION (For optional power heat duct)
An optional power heat duct may be used with this fireplace. It may be wired through the “ AN”
circuit to allow it to be adjusted by the remote (it may also be wired through a wall-mounted
rheostat). If it is wired through the “ AN” circuit, it may be adjusted from low “1” to high “3”. Use the
arrow keys to adjust the setting. Once the desired setting is made, the remote will alter the setting
after approximately 8 seconds (and the remote display will stop blinking).
NOTE: The fireplace must be on (either manual or thermostat) to adjust the fan. Because the fan
uses a heat-activated switch, it will not turn on until the fireplace is up to temperature.
LIGHT FUNCTION
The built-in accent light located inside the fireplace may be adjusted from “O ” to high “3” (a
total of 4 settings). Use the arrow keys to adjust the setting. Once the desired setting is made, the
remote will alter the setting after approximately 8 seconds (and the remote display will stop
blinking).
AUX FUNCTION
This function is not used on this fireplace.
TIMER FUNCTION
The timer function allows you to turn the fireplace on from 10 to 180 minutes. Use the arrow keys
to select the desired time. The fireplace will then turn off after the specified time. Once the
desired setting is made, the remote will alter the setting after approximately 8 seconds (and the
remote display will stop blinking).
NOTE: The fireplace must be in manual mode, and on, for the timer function to work.

12 Operation
© Travis Industries 4090202 100-01213_000
PROGRAM FUNCTION (Programmable 7 day thermo tat)
The program function operate a follow :
• Each day has two periods (P1 , P2). Each
period has an “ON” time and an “O ” time.
• Each period is programmed for weekdays
(Monday through riday) and weekends
(Saturday and Sunday).
• Each period has a set temperature.
The remote come pre-programmed for the following:
• Monday through riday P1 ON @ 6:00AM O @ 8:00AM 70°.
• Monday through riday P2 ON @ 6:00PM O @ 9:00PM 70°.
• Saturday and Sunday P1 8:00AM to 10:00AM 70°.
• Saturday and Sunday P2 7:00AM to 10:00PM 70°.
To adju t the program time and temperature , do the following:
A Press the unction (“ n”) Key until the program functions start to blink.
B Press the “Set” button for 5 seconds.
C The P1 “ON” time will blink. Use the arrows to select the desired time.
D Press the “Set” button. This sets the P1 “ON” time.
E The temperature will blink. Use the arrows to select the desired temperature.
Press the “Set” button. This sets the temperature for P1.
G The P1 “O ” time will blink. Use the arrows to select the desired time.
H Press the “Set” button. This sets the P1 “O ” time.
I REPEAT STEPS “C” through “H” for P2.
J REPEAT STEPS “C” through “H” for the weekend P1 and P2.
NOTE: P2 must start after 4:00PM.
To Turn PROGRAM FUNCTION ON
A Press the unction (“ n”) Key until the program functions start to blink.
B Press the “Set” button. The You will notice the P1 or P2 symbol will appear in the program
section of the remote next to the time. This indicates the remote is in PROGRAM
UNCTION (Programmable thermostat).
To Turn PROGRAM FUNCTION OFF
A Press the unction (“ n”) Key to select either manual or thermostat mode.

Operation 13
© Travis Industries 4090202 100-01213_000
Starting the Fireplace for the First Time
• Burn the heater at a high setting for an extended period (up to 48 hours). This will cure the
painted surfaces. Fume from the paint curing and oil burning off the steel will occur. This is
normal. We recommend opening a window to vent the room.
• Conden ation may appear on the glass each time you start the fireplace - this is normal.
• Blue Flame will occur on the fireplace when it first comes on. After fifteen minutes the flames
will turn a more realistic yellow and orange color.
Continuous Pilot – For Very Cold Conditions
This fireplace can be configured to run with an intermittent or continuous (standing) pilot. or
normal conditions we recommend using the intermittent pilot (pilot is on only when the main
burner is on). or extremely cold conditions we recommend using a continuous pilot (pilot is on all
the time). By having the pilot on continuously, a draft is established in the vent, allowing the main
burner to turn on with less air-flow disruption.
Setting the Fireplace to Continuou Pilot
Press and hold down the “Set” and “Down” arrow buttons. “Continuous Pilot” will appear on the LCD
screen, indicating that the fireplace is configured for a continuous pilot. To reconfigure the
fireplace for an intermittent pilot, press and hold down the “Set” and “Down” arrow buttons until
“Continuous Pilot” is no longer visible on the LCD screen.
Normal Operating Odors
This appliance has several areas that reach high temperatures. Dust or other particles on these
areas may burn and create an odor. This is normal during start-up. You may notice the smell is
more acute if the appliance was left idle for a long period.
Power Outages
This fireplace utilizes household power (110 VAC) to power the receiver module and pilot system.
A separate battery box is included to provide power in case of power outages. If you experience a
power outage and the unit does not operate, make sure to replace the AA batteries in the battery
box (see “Battery Installation” on page 19).
Child Protection Feature
The remote can be disabled to prevent children from operating the fireplace. This is done by
holding down the “ n” and “Up” button for 5 seconds until “CP” (Child Protection) appears on the
screen in the “ROOM” temperature box. If any button is pressed on the remote “CP” will appear on
the screen indicating the child protection feature is on. To turn this feature off, hold down the “ n”
and “Down” button for 5 seconds until “CP” (Child Protection) disappears on the screen in the
“ROOM” temperature box

14 Maintenance
© Travis Industries 4090202 100-01213_000
Yearly Service Procedure
WARNING: Prior to removing the glass, shut off gas to the
appliance (or remove the batteries from the battery box and shut
off electricity to the fireplace). This prevents any chance of
accidental burner ignition when accessing the firebox.
• ailure to inspect and maintain the fireplace may lead to improper combustion and a potentially dangerous
situation. We recommend the following procedures be done by a qualified technician.
1. Remove the glass frame and log set (NOTE: the log are very fragile - see page 16). If severely
deteriorated, replace. Check the logs for sooting. A small amount of soot along the bottom of the logs is
normal. If excessive sooting is found, the fireplace will require adjustment. Contact your dealer.
2. Inspect the burner and remove any debris.
• Make sure the burner is not warped, cracked, or damaged.
• Check the firebox and area around the pilot to make sure there is no warping or damage.
• If any problem is found, discontinue use and contact your dealer for service.
3. Replace the log set. Clean and replace the glass. If the glass is damaged, replace. Make sure the gasket
along the perimeter of the glass contacts the face of the firebox and forms an air-tight seal. If it does not,
re-align or replace the gasket to insure an air-tight seal.
4. Start the burner. The flames should be orange/yellow and not touch the top of the firebox. If the pilot or
main burners do not burn correctly, contact your dealer for service.
5. Remove any debris or vegetation near the vent termination. Contact your dealer if any sooting or
deterioration is found near the vent termination.

Maintenance 15
© Travis Industries 4090202 100-01213_000
Glass Frame Removal and Installation
WARNING: Prior to removing the glass, shut off gas to the appliance (or remove the
batteries from the battery box and shut off electricity to the fireplace). This
prevents any chance of accidental burner ignition when accessing the firebox.
Warning: The appliance must
be completely cool before removing
the glass.
Warning: Do not strike or slam
the glass.
Remove the glass trim (see
directions to the right).
The glass frame is held in place with
two latches along the top and two
slots, with brackets, along the
bottom. Insert the glass latch tool
into the latch, pull it forward and up
to detach the latches (see pictures
below). Once the latches are free,
pivot the frame out and lift it off the
brackets at the bottom of the glass
frame.
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
Glass Frame
Glass Trim
Attach the glass trim to the glass frame by
inserting the hooks on the trim over the
studs on the glass frame. When properly
aligned, the frame will push straight in
and drop into place.
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA

16 Maintenance
© Travis Industries 4090202 100-01213_000
Log Set Installation
Ember Placement
Place the embers along the firebo floor and burner to help conceal the burner. Make sure none of
the embers are directly over the burner holes. See the photo below.
Rock Wool Placement
The included rock wool is placed on top of the burner to enhance the glow from the burner. The
rock wool works best when it is applied in a very thin, porous layer. The best method for
applying the rock wool is to brush it on to the burner. Compress a clump of rockwool between your
thumb and forefinger. Use a stiff brush to apply a thin layer of rockwool fibers onto the burner. Do
not use the entire bag of rockwool. Use only a small amount and save the remainder. Over-use of
rockwool will diminish the glow and may cause sooting or other adverse conditions.
Note how the embers do not
cover any burner holes. Place
the embers around the burner
to create a realistic effect.

Maintenance 17
© Travis Industries 4090202 100-01213_000
Log In tallation
NOTE: The logs are a mirror-image (same logs fit on left and right side). See the pictures below for
log placement
Bottom 3 log .
Middle 2 log .

18 Maintenance
© Travis Industries 4090202 100-01213_000
Top 2 log (la t 2 log )
Picture from oppo ite ide

Maintenance 19
© Travis Industries 4090202 100-01213_000
Picture from end (Pier only)
Glass Cleaning
The glass may be cleaned with a non-abrasive cleaner. To clean the inside of the glass, simply
remove the glass frame, place it on a non-scratching surface, and clean the inside surface. On the Pier unit,
the front glass is cleaned without removal from the fireplace.
WARNING: do not operate the fireplace without the glass assembly in place.
Battery Installation
This fireplace uses four AA batteries for operation during power outages. Place the batteries into
the battery box. In addition, two AAA batteries are required for the transmitter. See the directions
below for battery replacement.
Replace the
batteries
(size AAA).
Remove the
access cover.
AAA Battery
AAA Battery
TRANSMITTER
BATTERIES
AA Battery
AA Battery
AA Battery
AA Battery
FIREPLACE BATTERIES
(POWER BACKUP)

20 Maintenance
© Travis Industries 4090202 100-01213_000
Accent Light Bulb Replacement
WARNING: Use only 35 Watt 120 Volt T4 Halogen Bulbs (G6.35 Base)
Two accent lights are included in your fireplace to provide additional lighting. To replace, follow the directions below:
1 Shut off gas and electricity to the fireplace and let it cool for 15 minutes.
2 Remove the glass (see page 15) and logs (see page 16).
3 Remove the four corner screws holding the accent light assembly to the firebox ceiling. Do not remove the inner
screws, these hold the cover plate to the assembly. Carefully remove the assembly and place it upside down on
the firebox floor.
4 With the resting on top of the burner, remove the four screws holding the accent light cover plate to the
accent light assembly. Remove the cover plate, gasket and glass from the assembly.
5 The halogen bulb is now accessible inside the accent light assembly. Replace the halogen bulb with a 35
watt 120 volt T4 halogen bulb (G6.35 base).
NOTE : .Take care to not touch the bulb with your fingers –use
foam packing or paper towel to hold the bulb. With the bulb replaced, the assembly may be replaced inside the
fireplace. Make sure the gasket above and below the glass are properly located. Replace the assembly into the
firebox ceiling, making sure the electrical cord is fully inserted into the cavity above the accent light.