TREND T5E User manual

T5EV2
ORIGINAL
INSTRUCTIONS
Please read these instructions before use.
Failure to follow the warnings and instructions may
result in electric shock, fire and/or serious injury.

T5
Dear Customer
Thank you for purchasing this Trend product,
we hope you enjoy many years of creative and
productive use.
Please remember to return your guarantee card
within 28 days of purchase.
CONTENTS
TECHNICAL DATA____________________ 1
SAFETY ___________________________ 2-3
ELECTRICAL SAFETY ________________ 4
EC DECLARATION OF CONFORMITY ___ 5
ITEMS ENCLOSED ___________________ 5
DESCRIPTION OF PARTS______________ 6
ASSEMBLY & ADJUSTMENT
– Dust Extractor Spout _________________ 7
– Handle Direction Arrow _______________ 7
– Switching On & Off___________________ 8
– Depth of Cut ________________________ 8
– Fitting & Removing Cutters ____________ 9
– Speed Control _____________________ 10
– Fine Height Adjuster_________________ 10
– Fixing Points_______________________ 10
OPERATION
– Cutting Direction & Feed Speed _______ 11
– Side-fence Routing__________________ 12
– Template Guide Bush Routing_________ 13
– Beam Trammel Routing ______________ 14
– Bearing Guided Cutters ______________ 15
– Freehand Routing & Batten Routing ____ 16
MAINTENANCE _____________________ 17
ENVIRONMENTAL PROTECTION_______ 17
GUARANTEE _______________________ 17
SPARE PARTS
– Spare Parts List __________________ 18-19
– Spare Parts Diagram ________________ 20
Definitions: Safety Guidelines
The definitions below describe the level of
severity for each signal word. Please read the
manual and pay attention to these symbols.
The following symbols are used throughout this
manual:
WARNING: indicates a potential
hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION: Indicates a potentially
hazardous situation which, if not avoided,
may result in minor or moderate injury.
NOTICE: Indicates a practice not related to
personal injury which, if not avoided, may
result in property damage.
Denotes risk of electric shock.
Denotes risk of fire.
Additional Symbols Used
Wear Personal Protective Equipment
(PPE). Ear, eye and respiratory
protection must be worn.
Denotes risk of personal injury, loss of
life or damage to the tool in case or
non-observance of the instructions in this
manual.
☎If you require further safety advice,
technical information or spare parts,
please call Trend Technical Support or
visit www.trend-uk.com

T5
-1-
INTENDED USE
The router is intended for routing grooves,
edges, profiles and slots as well as copy routing
in wood, wood based products and plastic. At
reduced speed with the appropriate router cutter
fitted non-ferrous alloys can also be routed.
This router is a professional power tool.
DO NOT use under wet conditions or in presence of
flammable liquids or gases.
DO NOT let children come into contact with
this appliance. Supervision is required when
inexperienced operators use this appliance.
This product is not intended for use by persons
(including children) suffering from diminished
physical, sensory or mental abilities; lack of
experience, knowledge or skills unless they are
supervised by a person responsible for their safety.
Children should never be left alone with this product.
The vibration emission level given in this information
sheet has been measured in accordance with
EN 60745 and may be used to compare one tool
with another. It may be used for a preliminary
assessment of exposure.
WARNING: The declared vibration emission level
represents the main application of the tool. However
if the tool is used for different applications, with
different accessories or poorly maintained, the
vibration emission may differ. This may significantly
increase the exposure level over the total working
period. An estimat ion of the level of exposure to
vibration should also take into account the times
when the tool is switched off or when it is running
but not actually doing the job. This may significantly
reduce the exposure level over the total working
period. Identify additional safety measures to
protect the operator from the side effects of vibration
such as: maintain the tool and the accessories,
keep hands warm, organisation of work patterns.
Voltage UK & Eire VAC 240/115
Europe VAC 230
Power input W 1010
Power output W 600
No-load speed min-1 9,000 -
27,000
Router carriage 2 columns
Router carriage mm 50
stroke
Revolver depth 3-step,
stop turret
stop with
graduation
Collet size UK & Eire inch 1/4
UK & Eire mm 6.35
Europe mm 8
Cutter diameter, mm 40
max.
Weight kg 2.85
Noise values and vibration valves
(triax vector sum) according to EN60745-2-17:
LPA (emission sound dB(A) 83
pressure level)
KPA (uncertainty for the dB(A) 3
given sound pressure)
LWA (sound power level) dB(A) 94
KWA (uncertainty for the dB(A) 3
given sound level)
Vibration emission
Value ah= m/s22.5
Uncertainty K= m/s21.5
ROUTER
T5E
TECHNICAL DATA

T5
-2-
SAFETY
WARNING:
Observe the safety regulations in the
instruction manual of the power tool
to be used. Please read the following
instructions carefully. Failure to do so
could lead to serious injury. When using
electric tools, basic safety precautions,
including the following should always be
followed to reduce the risk of fire, electric
shock and personal injury. Also observe
any applicable additional safety rules.
Read the following safety instructions
before attempting to operate this product.
PLEASE KEEP THESE
INSTRUCTIONS IN A SAFE PLACE.
The attention of UK users is drawn to The
Provision and Use of Work Equipment
Regulations 1998, and any subsequent
amendments.
Users should also read the HSE/HSC
Safe Use of Woodworking Machinery
Approved Code of Practice and Guidance
Document and any amendments.
Users must be competent with
woodworking equipment before using our
products.
IMPORTANT NOTE:
Residual Risk. Although the safety
instructions and operating manuals for
our tools contain extensive instructions
on safe working with power tools, every
power tool involves a certain residual risk
which cannot be completely excluded
by safety mechanisms. Power tools
must therefore always be operated with
caution!
General
1. Disconnect power tool and attachment
from power supply when not in
use, before servicing, when making
adjustments and when changing
accessories such as cutters. Ensure
switch is in “off” position. Always
ensure cutter has stopped rotating.
2.Always mount the power tool,
accessory or attachment in conformity
with the instructions. Only use
attachment and accessories specified
in the power tool manual. The tool or
attachment should not be modified or
used for any application other than
that for which it was designed. Do not
force tool.
3.Keep children and visitors away. Do
not let children or visitors touch the
tool, accessory or attachment. Keep
children and visitors away from work
area. Make the workshop child proof
with padlock and master switch.
4.Dress properly. Do not wear loose
clothing or jewellery, they can be
caught in moving parts. Rubber
gloves and non-skid footwear
is recommended when working
outdoors. Wear protective hair
covering to contain long hair.
5.Consider working environment. Do
not use the product in the rain or in
a damp environment. Keep work
area well lit. Do not use power tools
near gasoline or flammable liquids.
Keep workshop at a comfortable
temperature so your hands are not
cold. Connect machines that are
used in the open via a residual current
device (RCD) with an actuation
current of 30 mA maximum. Use only
extension cables that are approved for
outdoor use.
6.The accessory or attachment must be
kept level and stable at all times.
7.Keep work area clean. Cluttered
workshops and benches can cause
injuries. Ensure there is sufficient
room to work safely.
8.Secure idle tools. When not in use,
tools should be stored in a dry and
high or locked up place, out of reach
of children.
9.For best control and safety use
both hands on the power tool and
attachment. Keep both hands away
from cutting area. Always wait for the
spindle and cutter to stop rotating
before making any adjustments.
10. Always keep guards in place and in
good working order.
11. Remove any nails, staples and other
metal parts from the workpiece.
12. Maintain tools and cutters with care.
Keep cutters sharp and clean for
better and safer performance. Do
not use damaged cutters. Follow
instructions for lubricating and
changing accessories. Keep handles
dry, clean and free from oil and
grease.
13. Maintain accessories. Do not use
damaged accessories. Only use
accessories recommended by the
manufacturer.
14. Check damaged parts. Before
operation inspect the attachment,
the power tool, the cable, extension
cable and the plug carefully for signs
of damage. Check for alignment of
moving parts, binding, breakage,
mounting and any other conditions
that may effect its operation. Have any
damage repaired by an Authorised
Service Agent before using the tool or
accessory. Protect tools from impact
and shock.
15. Do not use tool if switch does not turn
it on or off. Have defective switches
replaced by an Authorised Service
Agent.
16. Don’t over reach. Keep proper footing
and balance at all times. Do not
use awkward or uncomfortable hand
positions.
17. Don’t abuse the cable.Never carry
power tool or accessory by cord or
pull it to disconnect from the socket.
Keep cord from heat, oil and sharp
edges. Always trail the power cord
away from the work area.
18. Connect dust extraction equipment.
If devices are provided for the
connection of dust extraction and
collection facilities, ensure these are
connected and properly used.
19. Check all fixing and fastening nuts,
bolts and screws on power tool,
attachment and cutting tools before
use to ensure they are tight and
secure. Periodically check when
machining over long periods.
20. Stay alert. Watch what you are doing.
Use common sense. Do not operate
tools when you are tired, under the
influence of drugs or alcohol.
21. Personal Protective Equipment (PPE)
for eye, ear and respiratory protection
must be worn. All PPE must meet
current UK and EU legislation.
22. Do not leave tools running
unattended. Do not leave tool until it
comes to a complete stop.
23. Always clamp workpiece being
machined securely.
24. Only use cutting tools for
woodworking that meet EN847-
1/2 safety standards, and any
subsequent amendments.
25. Vibration levels. Hand held power
tools produce different vibration
levels. You should always refer to
the specifications and relevant Health
& Safety Guide.
Routing Safety
1.Read and understand instructions
supplied with power tool, attachment
and cutter.
2.Keep hands, hair and clothing clear of
the cutter.
3.Remove adjusting keys and
spanners. Check to see that keys
and adjusting spanners are removed
from the router tool, cutter and
attachment before turning router on.
Make sure cutter can rotate freely.
4.Noise. Take appropriate measures
for the protection of hearing if
the sound pressure of 85dB(A) is
exceeded. Routing sound pressure
may exceed 85dB(A), so ear
protection must be worn.
5.Eye protection. Always wear eye
protection in the form of safety
goggles, spectacles or visors to
protect the eyes.
6.Respiratory protection. Always wear
a face or dust mask, or powered
respirator. Dust masks/filters should
be changed regularly.
7.Do not switch router on with the cutter
touching the workpiece. At the end of
the cut, release the router plunge and
allow spindle to stop rotating. Never
use the spindle lock as a brake

T5
-3-
8.The direction of routing must always
be opposite to the cutter’s direction of
rotation. Do not back-cut or climb-cut.
9.Check before cutting that there are
no obstructions in the path of the
router. Ensure there are no obstacles
beneath workpiece when cutting full
thickness, and that a sacrificial work
surface is used.
10.Hold power tool by insulated gripping
surfaces, because the cutter may
contact its own cord. Cutting the “live”
wire may make exposed metal parts
of the powertool “live” and shock the
operator.
11.Use clamps or another practical way
to secure and support the workpiece
to a stable platform. Holding the work
by your hand or against the body
leaves it unstable and may lead to
loss of control.
Router Cutter Safety
1.Cutting tools are sharp. Care should
be taken when handling them. Do not
drop cutters or knock them against
hard objects. Handle very small
diameter cutters with extra care.
Always return cutter to its packaging
after use.
2.Always use cutters with a shank
diameter corresponding to the size of
the collet installed in your tool.
3.The maximum speed (n.max) marked
on the tool, or in instructions or on
packaging shall not be exceeded.
Where stated the speed range shall
be adhered to. Recommended speeds
are shown in the Trend Routing
Catalogue and/or website.
4. Always use router cutters in a router.
Drill and boring bits must not be
used in a router. Router cutters
must only be used for the material
cutting application for which they are
designed. Do not use on metal or
masonry.
5.Never use cutters with a diameter
exceeding the maximum diameter
indicated in the technical data of the
powertool or attachment used.
6. Before each use check that the
cutting tool is sharp and free from
damage. Do not use the cutting tool
if it is dull, broken or cracked or if in
any other damage is noticeable or
suspected.
7. Cutters should be kept clean. Resin
build up should be removed at regular
intervals with Resin Cleaner. The use
of a PTFE dry lubricant will reduce
resin build up. Do not use PTFE spray
on plastic parts.
8.When using stacked tooling (multi-
blade, block and groover etc.) on a
spindle arbor, ensure that the cutting
edges are staggered to each other to
reduce the cutting impact.
9.Cutter shanks should be inserted
into the collet all the way to the line
indicated on the shank. This ensures
that at least
3
⁄ 4 of the shank length
is held in the collet. Ensure clamping
surfaces are cleaned to remove dirt,
grease, oil and water.
10. Observe the correct assembly and
fitting instructions in the router
instruction manual for fitting the collet,
nut and cutter.
11. Tool and tool bodies shall be clamped
in such a way that they will not
become loose during operation. Care
shall be taken when mounting cutting
tools to ensure that the clamping is by
the shank of the cutting tool and that
the cutting edges are not in contact
with each other or with the clamping
elements.
12. It is advisable to periodically check
the collet and collet nut. A damaged,
worn or distorted collet and nut can
cause vibration and shank damage.
Do not over-tighten the collet nut
13. Do not take deep cuts in one pass;
take several shallow or light passes
to reduce the side load applied to the
cutter and router. Too deep a cut in
one pass can stall the router.
14. In case of excessive vibrations whilst
using the router stop immediately and
have the eccentricity of the router,
router cutter and clamping system
checked by competent personnel
15. All fastening screws and nuts should
be tightened using the appropriate
spanner or key and to the torque
value provided by the manufacturer.
16. Extension of the spanner or tightening
using hammer blows shall not be
permitted.
17. Clamping screws shall be tightened
according to instructions provided by
the manufacture. Where instructions
are not provided, clamping screws
shall be tightened in sequence from
the centre outwards.
18. Do not touch the cutter immediately
after operation; it may be extremely
hot and could burn your skin.
Using Routers In A Fixed Position
1.Attention should be made to the
HSE’s Safe Use of Vertical Spindle
Moulding Machines Information Sheet
No.18 and any revisions.
2. After work, release the router plunge
to protect the cutter.
3.Always use a push-stick or push-
block when making any cut less than
300mm in length or when feeding the
last 300mm of the cut.
4.The opening around the cutter should
be reduced to a minimum using
suitably sized insert rings in the table
and closing the back fence cheeks or
fitting a false fence on the back fence.
5.Whenever possible use a work
holding device or jig to secure
component being machined. Ensure
any attachment is securely fitted to
the workbench, with table surface at
approximately hip height.
6.Use a No-Volt Release Switch. Ensure
it is fixed securely, easily accessible
and used correctly.
7.In router table (inverted) mode, stand
to the front right of the table. The
cutter will rotate anti-clockwise when
viewed from top so the feed direction
is from the right (against the rotation of
the cutter). In overhead mode, stand to
the front left of the machine table and
the feed direction is from the left.
8.Do not reach underneath table or put
your hands or fingers at any time in
the cutting path while tool is connected
to a power supply.
9.Never thickness timber between the
back of the cutter and the backfence.
Useful Advice When Routing
1.Judge your feed rate by the sound
of the motor. Feed the router at a
constant feed rate. Too slow a feed
rate will result in burning.
2. Trial cuts should be made on waste
material before starting any project.
3.When using some attachments e.g.
a router table or dovetail jig, a fine
height adjuster is recommended.
4.When using a template guide bush,
ensure there is sufficient clearance
between cutter tip and inside edge
of bush and that it cannot come into
contact with collet and nut. Ensure
cutter and guide bush are concentric.
Router Cutter Repair/Maintenance
1.Repair of tools is only allowed in
accordance with the manufacturers
instructions.
2.The design of composite (tipped)
tools shall not be changed in process
of repair. Composite tools shall be
repaired by a competent person i.e.
a person of training and experience,
who has knowledge of the design
requirements and understands the
levels of safety to be achieved.
3.Repair shall therefore include, e.g.
the use of spare parts which are in
accordance with the specification
of the original parts provided by the
manufacturer.
4.Tolerances which ensure correct
clamping shall be maintained.
5.Care shall be taken that regrinding
of the cutting edge will not cause
weakening of the body and the
connection of the cutting edge to the
body.
Version 8.0 08/2017

T5
-4-
Power Supply
The electric motor has been designed for one
voltage only. Always check that the power
supply corresponds to the voltage on the rating
plate. Machines marked for 230 volt can also be
operated from a 220 volt supply.
The T5 is double insulated in
accordance with EN 60745; therefore no
earth wire is required.
Mains Plug Replacement
(UK & Ireland only)
Always check the condition of the cable and plug
before starting with your work.
Should your mains plug need replacing and you
are competent to do this, proceed as instructed
below. If you are in doubt, contact an authorised
Trend repair agent or a qualified electrician.
nDisconnect the plug from the supply.
nCut off the plug and dispose of it safely;
a plug with bared copper conductors is
dangerous if engaged in a live socket outlet.
nOnly fit 13 Amperes BS 1363A approved
plugs fitted with a 13 Amp A.S.T.A approved
BS 1362 fuse (1).
nThe cable wire colours, or a letter, will be
marked at the connection points of most
good quality plugs. Attach the wires to their
respective points in the plug (see below).
Brown is for Live (L) (2) and Blue is for
Neutral (N) (3).
nBefore replacing the top cover of the mains
plug ensure that the cable restraint (4) is
holding the outer sheath of the cable firmly
and that the two leads are correctly fixed at
the terminal screws.
Using an Extension Cable
n If an extension cable is required, use an
approved triple core extension cable suitable
for the power input of this tool (see technical
data).
nWhen using a cable reel, always unwind the
cable completely.
nAlso refer to the table below.
Conductor size (mm2)Cable rating (Amperes)
0.75 6
1.00 10
1.50 15
2.50 20
4.00 25
Cable length (m)
7.5 15 25 30 45 60
Voltage Amperes Cable rating (Amperes
115 0 - 2.0 6 6 6 6 6 10
2.1 - 3.4 6 6 6 6 15 15
3.5 - 5.0 6 6 10 15 20 20
5.1 - 7.0 10 10 15 20 20 25
7.1 - 12.0 15 15 20 25 25 -
12.1 - 20.0 20 20 25 - - -
230 0 - 2.0 6 6 6 6 6 6
2.1 - 3.4 6 6 6 6 6
6
3.5 - 5.0 6 6 6 6 10 15
5.1 - 7.0 10 10 10 10 15 15
7.1 - 12.0 15 15 15 15 20 20
12.1 - 20.0 20 20 20 20 25 -
ELECTRICAL SAFETY
3
4
2
1
13 AMP
WARNING: Never connect to a light
socket. Never connect the live (L)
or neutral (N) wires to the earth pin
marked E or .
For 115V units with a power rating exceeding
1500W we recommend to use a plug to
BS4343 standard.

T5
-5-
EC DECLARATION OF
CONFORMITY
MACHINERY DIRECTIVE
ROUTER
T5E
Trend declares that the product described under
Technical Data is in compliance with
2006/42/EC, and has been designed in
accordance with EN 60745-1:2009+A11:2010
EN 60745-2-17:2010.
This product also complies with Directives
2014/30/EU, 2011/65/EU and the following
harmonised standards EN 55014-1, EN 55014-2,
EN 61000-3-2 and EN 61000-3-3.
For more information please contact Trend at the
following address or refer to back of manual.
The undersigned make this declaration on behalf
of Trend Machinery & Cutting Tools Ltd.
Techincal Director
Neil McMillan
Trend Machinery & Cutting Tools Ltd
Unit 6 Odhams Trading Estate
St Albans Road, Watford
Herts, WD24 7TR
United Kingdom
01.01.2018
RESIDUAL RISKS
In spite of the application of the relevant safety
regulations and implementation of safety devices,
certain residual risks cannot be avoided. These
are:-
nImpairment of hearing.
nRisk of personal injury due to flying particles.
nRisk of burns due to accessories becoming
hot during operation.
nRisk of personal injury due to prolonged use
MARKINGS ON TOOL
The following pictures are shown on the appliance.
Read instruction manual before use.
Date Code Position
The year of manufacture is on the rating plate.
Additional Specific Safety Rules for
Cutters
nHold power tool by insulated gripping
surfaces, because the cutter may contact
its own cord. Cutting a “live” wire may make
exposed metal parts of the power tool “live”
and shock the operator.
nUse the clamps or another practical way to
secure and support the workpiece to a stable
platform. Holding the work by your hand or
against the body leaves it unstable and may
lead to loss of control.
nFor personal protection, ALWAYS wear a dust
mask.
nAlways use cutters suitable for a speed of
30,000 min and marked accordingly.
nNever use cutters with a diameter exceeding
the maximum diameter indicated in the
Technical Data.
This router is designed to accept professional
cutters of straight, profile, rabbet, and grooved
type with rated minimum speed of 30,000 min-1.
WARNING: We recommend the
use of a residual current device
with a residual current rating of
30mA or less.
WARNING: Always consider
the following compulsive
conditions:
nUse 6.35mm shank diameter for straight,
rebate, groove and profile cutter.
nMaximum cutter diameter:
T5 40mm at 35mm cutting depth
T5 Groove Cutter:
40mm at 6mm cutting depth

T5
-6-
E
D
F
G
H
I
K
J
L
M
Y
N
OQ
W
R
S
P
Z
T
U
V
A
B
C
X
A Plunge locking grip knob
B Depth of cut scale
C Depth stop
D Motor housing
E Power cable
F On/Off switch
G Fixed Grip knob
H Spindle lock
I Collet nut
J Dust spout 35mm dia.
K Thumb knob with anti-vibration
spring to secure fence rods
L Router base
M Template guide bush dia.
20mm
N Collet
DESCRIPTION OF PARTS
ITEMS ENCLOSED
1 x Parallel side-fence with micro
adjuster
1 x Fence rods (pair)
2 x Adjustable fence cheeks with fixing
screws
1 x Collet
1
⁄ 4 ” (6.35mm) UK & Eire
1 x Collet 8mm Europe
1 x Spanner (17mm A/F)
1 x Guide bush 20mm and fixing screws
1 x Beam trammel attachment
1 x Dust extractor spout
1 x Grip knob direction arrow sticker
1 x Instruction manual
1 x Guarantee registration card
nCheck for damage to the tool, parts
or accessories which may have
occurred during transport.
nTake the time to thoroughly read
and understand this manual prior to
operation.
O Adjustable fence cheek
P Thumb knob with anti-vibration
spring for side-fence rod
Q Beam trammel attachment
R Side-fence
S Knob for micro-adjustment
T 3-way turret stop
U Spanner (17mm A/F)
V Thumb knob with anti-vibration
spring for depth stop
W Fence rods dia. 8mm x 300mm
X Variable speed control dial
Y Template guide bush fixing
screw
Z Grip knob direction arrow
sticker

T5
-7-
1
2
Fitting and Removing the
Dust Extractor Spout
n Insert the extractor spout in channel ‘A’ of the
routing base.
The extractor spout is suitable for dust
extractors with a hose diameter of 35mm. The
spout can be installed from either side. To
ensure maximum plunge it is recommended
to fit spout to back of machine.
nPress the extractor spout down and forward
until it latches into channel ‘B’.
Dismantle in reverse order.
WARNING: Whenever possible use the
dust extraction spout with a suitable
extractor when routing.
Fitting the Plunge Grip Knob Direction
Arrow Sticker
nRemove direction arrow (2) from backing
paper and apply to plunge locking grip knob
(1).
nOrientate label so that solid arrow head points
away from the front of the router.
nWrap arrow around grip knob neck, ensure it
is correctly positioned and firmly stuck down.
35mm
A
B
(2)
(1)
(1)
(2)
Fitting Dust
Extractor
Spout
Removing
Dust
Extractor
Spout
ASSEMBLY & ADJUSTMENT
The direction arrows identify the
plunge locking grip knob and the
direction for locking and unlocking
the router carriage.
NOTICE: Do not overtighten
plunge grip locking knob.

T5
-8-
5
3
2
4
Switching On & Off
nA slide switch above the fixed grip knob is
used to turn the router on and off.
nThe T5 has a soft start feature when switched
on and will take 1–2 seconds to reach full
running speed.
Adjusting the Depth of Cut
nPlace the machine on the workpiece.
nPre-set the 3-way turret stop (1) as required.
nUndo the thumb knob (2) for securing the
depth stop (3).
nUndo the plunge locking grip knob (4).
nLower the machine slowly until the cutter just
touches the workpiece and secure it with the
locking grip knob.
n Raise the depth stop in accordance with the
scale (5) for the depth of cut required and
clamp in place with the thumb knob (2).
The gap between the depth stop and the
turret stop screw determines the depth of
cut.
The rotating turret stop screws can be used for
pre-setting up to three depths of cut. Their height
can be adjusted using a screwdriver (6) and an
8mm A/F spanner (7).
ON
Slide switch
OFF
OFF
ON
0
I
1
7
6
3
1
6
3
7
By turning the turret
stop, three depth
settings can be
quickly made.
nWARNING: Make sure the machine
is switched off before connecting it
to the power supply!
nWARNING: Never make adjustments
when the router is running or
plugged in.
WARNING: To ensure a smooth plunge
action, always apply more pressure to
the plunge locking grip knob and less
pressure to the fixed grip knob.

T5
-9-
How to Fit and Remove a Router
Cutter
Fitting Cutters
nInsert at least 3/4 of the shank length of the
cutter (1) into the collet.
nPress the spindle lock (2) forward until the
router spindle is locked (you may need to turn
the spindle slightly to engage it).
nTighten the collet nut with the spanner (3). Do
not use excessive force.
Removing Cutters
nUndo the 17mm A/F collet nut with the
spanner.
nKeep turning the spanner until the collet nut
tightens and then loosens again. This is the
fail-safe mechanism releasing the collet.
nThe cutter should now slide out.
nEach time you finish using a cutter, remove it
and store it in a safe place.
nWARNING: Do not tighten the collet
without a cutter fitted.
nWARNING: Always use cutters with
shanks which match the diameter of
the collet.
nWARNING: Deep cuts should always
be routed in several passes.
nWARNING: Do not use cutters larger
than 40mm unless the router is
fitted in a router table.
CLICK
(2)
(3)
(1)
Correct Sequence for Fitting Collet,
Nut and Cutter

T5
-10-
Setting the Electronic Speed
Control Dial
The speed is infinitely variable from 9,000 to 27,000
rpm using the electronic speed control dial (1) for
uniform cutting results in all types of wood, plastics
and in aluminium.
nTurn the electronic speed control dial to the
required level. The dial is numbered from 1 to
5 and corresponds to router speeds from 9,000
rpm to 27,000 rpm.
nGenerally, use the lower settings for large
diameter cutters and the higher settings for small
diameter cutters. The correct setting will also
depend on the density of the material, depth of
cut and feed speed of the router, as severe loss
of rpm denotes motor overload. In most cases
the slowest speed required for large cutters with
smaller shank sizes is Dial No 3-4.
Fitting the Fine Height Adjuster
Optional Accessory Ref. FHA/001
The optional fine height adjuster should be
used when fine adjustment is required. This
is especially recommended when using our
dovetail jig or router table.
nRemove the depth stop and replace it with the
fine height adjuster.
nLeave the plunge locking grip knob and the
thumb knob loose and thread the end of the
fine height adjuster onto the longest screw.
nSet the depth of cut by turning the fine height
adjuster handle until the correct height is
reached. Then lock the carriage clockwise
with the plunge locking grip knob.
CAUTION: Remember to always
unlock the carriage by turning the
plunge locking grip knob anti-
clockwise when adjusting the height
with the fine adjuster.
Fixing Points for Accessories
The router has two threaded holes M6 in its
base that allow fitting of accessories and also
fitting to router tables.
A whole range of accessories are shown in the
Trend Routing Catalogue.
1
115mm
15mm
M6
Dial Router
No. Speed
1 9,000 rpm
2 13,000 rpm
3 18,000 rpm
4 23,500 rpm
5 27,000 rpm

T5
-11-
OPERATION
1
34
2
Moulding Natural Timbers
When edge moulding natural timbers, always
mould the end grain first, followed by the long
grain. This ensures that if there is ‘breakout’, this
will be removed when the long grain is routed.
Step One
Plunge down, ensuring more
pressure is applied to the
plunge locking grip knob,
and lock the motor carriage,
with the plunge locking grip
knob.
Step Two
Carry out the routing
operation.
Step Three
Release the plunge locking
grip knob and the motor
carriage returns to the
normal position.
Sequence of plunging
Feed Speed
The speed at which the cutter is fed into the wood
must not be too fast that the motor slows down, or
too slow that the cutter leaves burn marks on the
face of the wood. Practice judging the speed by
listening to the sound of the motor when routing.
Feed Direction
When routing along an edge, the direction of the
router travel should be against that of the rotation
of the cutter. This will create the correct cutting
action and prevent the cutter ‘snatching’. It will
Feed direction
of router
Direction of
cutter rotation
Feed direction
of router
Direction of
cutter rotation
WARNING: The direction of routing
must always be opposite to the
cutter’s direction of rotation,
otherwise there is a risk of kick-back.
Cutting Direction
WARNING: To reduce the risk of
serious personal injury, always
use proper hand position as
shown.
WARNING: To reduce the risk of
serious personal injury, always
hold securely in anticipation of a
sudden reaction.
Proper hand grip
requires one hand
on each grip as
shown.
NOTICE: Do not overtighten
plunge locking knob.
WARNING: To ensure a smooth plunge
action, always apply more pressure to
the plunge locking grip knob and less
pressure to the fixed grip knob.
also pull the router towards the workpiece and
hence the side-fence or guide bearing will be less
likely to wander from the edge of the workpiece.

T5
-12-
Side-Fence Routing
The side-fence is used to guide the router when
moulding, edge profiling or rebating the edge of
the workpiece or when routing grooves and slots
in the centre of the workpiece, parallel
to the edge.
The edge of the workpiece
must be straight and true.
The cheeks are adjustable
and should be set ideally
with a 3–4mm gap each
side of the cutter.
Fitting and using the Side-Fence
nMake sure the thumb knobs (3) are fully
released. Slide the guide rods (1) into the
routing base (2) and tighten the thumb knobs
(3).
nAdjust the side-fence (4) to the required
distance and clamp in place with the thumb
knobs (5).
nThen lower the cutter height until the cutter is
just above the workpiece.
nFine adjustments are possible by slackening
the thumb knobs (5), adjusting the micro-
adjustment knob (6) and securing it again with
the thumb knobs (5). One revolution of the
micro-adjustment knob (6) equals 1.25mm of
side-feed.
nLower the cutter onto the workpiece and set
the cutter height by raising the depth stop (7)
the required distance.
nSwitch on the router and when the cutter
reaches full speed, gently lower the cutter into
the workpiece and lock the plunge.
nFeed along the timber, keeping sideways
pressure (A) to ensure the side-fence does not
wander away from the workpiece edge and
downward pressure on the inside hand (B) to
prevent the router from tipping.
nWhen finished, raise the router, secure with
the plunge locking grip knob (8) and switch off.
C
D
When starting the cut,
keep the pressure on the
front cheek (C) until the
back cheek contacts the
workpiece edge.
At the end of the cut, keep
pressure on the back cheek
(D) until the cut is finished.
This will prevent the router
cutter swinging in at the
end of the workpiece and
‘nipping’ the corner.
CAUTION: Ensure working position
is comfortable and at a suitable
working height.

T5
-13-
Guide bush
fitted to
router
E
d
D
Template
FORMULA
(D-d)
E = 2
Using the Guide Bush
The 20mm guide bush (1) is fastened to the
router’s base from beneath using the two M5
countersunk machine screws (2) supplied.
Routing with a Template
The guide bush is used in conjunction with a
template when the routing operation is repetitive
or the workpiece is complex in shape. The
template is fixed to the upper surface of the
workpiece.
A cutter is chosen with a diameter which will
pass through the centre of the bush leaving
enough clearance. The cutter can be straight or
shaped. The router can then be guided around
the template so that the shape of the template
will be replicated.
Making the Template
The template is cut from 6mm or 1/4” MDF,
plywood or plastic to the shape required. The
guide bush offset needs to be allowed for when
calculating the shape of the template. The
template must be smaller by an amount equal
to the difference between the ‘outer edge of the
guide ring’ and the ‘outer edge of the cutter’.
See below for the offset calculation. The edge
of the template must be free of imperfections as
these will be replicated in the final workpiece.
Calculations for template offset
Template
Template
guide bush
Workpiece
Guide
bush ring
Cutter
2
1
Using a template
to rout an edge
straight
Alternatively it can
be used for cutting
shapes or making
panelling grooves.

T5
-14-
Beam Trammel Routing
A
B
C
2
6
1
3
4
5
Fitting the beam trammel attachment
nFit the beam trammel attachment (A) to the
end of one rod and tighten wing nut (C)
securely.
nHeight adjustment of the pivot point can
be achieved by loosening wing nut (C) and
rotating screw (B).
nOnce set to the correct height, lock securely
wing nut (C).
Cutting Arcs with the Router
nPlace the machine on the workpiece.
nSet the cutting depth using the depth stop (2).
nFasten the fence rod (1) in the routing base
(3) with the thumb knob (4).
nFit on the beam trammel point (5) as shown.
nMeasure the radius required from beam
trammel point to edge of cutter. Fix the point
of the beam trammel on the centre point
required on the component.
nSwitch on the machine.
nAfter releasing the plunge locking knob (6),
lower the machine slowly as far as the depth
stop and lock it there.
nCut grooves, rebates etc. at a steady rate of
feed, in an anti-clockwise direction. Ensure
the beam trammel point does not move.
nWhen finished, release locking knob to raise
the machine.
nSwitch off the machine.

T5
-15-
Bearing Guided Cutters
Ball Bearing Guided Cutters
Edge profiling and shaping cutters are available
with a bearing fitted to the end. This enables
shaped or straight workpieces to be routed
without the need for a guiding device such as a
side-fence or batten.
The edge must be free from imperfections
as these will be reflected in the finish of the
mould. Often alternative diameters of bearings
are offered which will change the shape of the
resulting mould.
With certain shapes such as the chamfer cutter
below, increasing the depth of cut will produce a
larger chamfered edge.
nFit the bearing guided cutter into the router
collet.
nPlace router onto the workpiece.
nSet height of cutter using the depth stop (1).
nSwitch on the machine.
nAfter releasing the plunge locking grip knob
(2), lower the machine slowly as far as the
depth stop.
nWith bearing of cutter running along board
edge, mould the edge of the workpiece by
moving the router in the direction shown.
nA continuous motion should be used to
prevent burning of the workpiece. When
possible, take a number of passes at
increased cutter depths. A light final pass will
produce a good finish.
nWhen complete, retract the carriage by
releasing the locking grip knob.
nSwitch off the router.
2
1
The guide bearing
ensures the cutter
follows the workpiece.
Where the material thickness leaves
insufficient room for the bearing to make
contact, a second piece of material can
be temporarily fixed beneath it for the ball
bearing to follow.
CAUTION: Keep downward pressure
with the inside hand to prevent the
router from tipping.

T5
-16-
Freehand Routing with the Router
The T5 can also be used for sign writing or
creative freehand work without any form of
guide.
With practice, numbers or name plate designs
can be routed freehand. Draw the design or
motif on the workpiece and then rout the design,
taking shallow passes.
Batten Routing
Where a side-fence cannot be used, it is also
possible to guide the router along a batten
clamped across the workpiece (with an
overhang at both ends).
Guidance from a batten is similar to that
obtained from a side-fence. This method is
appropriate if the edge of the workpiece is not
straight or is not very smooth or simply the
guide rods of the side-fence are too short for
the job.
Use the straight edges of the router base and
calculate the distance required from the edge
of the batten to the cut required. Always
check that the clamps do not obstruct the
path of the router before starting the cut.
Standard technique is used, and
side pressure applied to ensure
the router does not wander from
the batten.
A V groove
cutter is ideal for
engraving designs
at shallow depths.
Please use only Trend original accessories.
After use, remove all accessories,
and return tool to its storage case.

T5
MAINTENANCE
Cleaning
nKeep the machine clean at all times. Some
maintenance products and solvents may
damage the plastic parts, these include
products containing Benzene, Trichloroacetyl
Chloride and Ammonia.
nNever use any caustic agents to clean the
plastic parts.
nUndo the two screws (1) in the top of the vent
housing (2). Lift the vent housing off and lift
the speed control circuit board (3) out of the
way.
nRemove brush clamp (4) by undoing fixing
screws (5).
nDisconnect the wire (6) and remove the carbon
brush (7).
nInsert the new brush and press the connector
firmly on to the tag. Refit brush clamp (4) and
screws (5). Refit the speed control board (3) and
then secure vent housing (2) with
the two screws (1).
nAlways use original T5 spare parts.
Changing Brushes
4
3
1
2
6
5
7
WARNING: It is advisable to
have the brushes replaced by
an authorised Trend Service
Agent. The router will also be
given a thorough inspection.
WARNING: Ensure machine
is isolated from power
supply.
Lubrication
nThe bearings of the machine need no
lubrication, as they are sealed. The two
plunge columns on the routing base should
be slightly oiled from time to time.
nKeep the cooling vents on the motor housing
clean and unobstructed at all times. Blow
out any dust and dirt at regular intervals.
nVisually check the carbon brushes. In the
event of excessive sparking, they may need
changing.
nAfter about 40 operating hours inspection
by a authorised Trend service agent is
recommended.
Storage
nAfter use return the tool to its storage case
or its packaging.
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing
as waste.
Accessories and packaging should be sorted
for environmental-friendly recycling.
Separate collection.
This product must not be disposed of
with normal household waste.
Household User
Local regulations may provide for separate
collection of electrical products from the
household, at municipal waste sites or by
retailer when you purchase a new product.
Please call Trend Customer Services for
advice as to how to dispose of unwanted Trend
electrical products in an environmentally safe
way or visit www.trend-uk.com
Business Users
Please call Trend Customer Services for
disposal of unwanted Trend electrical products.
GUARANTEE
The unit carries a manufacturers guarantee in
accordance with the conditions on the enclosed
guarantee card.
For the location of your nearest Trend Service
Agent, please call Trend Customer Services or
see our stockist locator at www.trend-uk.com.
-17-

T5
-18-
T5 V2 - SPARE PARTS LIST v11.0 07/2017
No. Qty. Desc. Ref.
1 1 Stator Housing WP-T5/001
2 1 Top Vent Housing WP-T5E/002
3A 1 Base Complete V2 WP-T5/003A
4A 1 Lower Bearing Housing V2 WP-T5/004A
5 1 Spring for Revolving Guide WP-T5/005
6 1 Ball for Revolving Guide WP-T5/006
8A 1 Revolving Guide V2 WP-T5/008A
9 3 Nut Hex M5 WP-NUT/05
10 1 Threaded Pin M5 x 15mm Revolving Guide Cheese Head WP-T5/010
11 7 Thumb Knob M6 Male x 12mm WP-T5/011
12A 1 Revolving Guide Stepped Screw M6 WP-T5/012A
13 1 Threaded Pin M5 x 20mm Cheese Head WP-T5/013
14 1 Depth Stop WP-T5/014
15A 2 Grip Knob V2 WP-T5/015A
16 7 Spring 12mm for Thumb Knob WP-T5/016
17 1 Switch T5, T5/EURO & T5EL V2 WP-T5E/017
18 1 Bottom Bearing 35mm x 17mm x 10mm 6003 WP-T5/018
19 2 Screw Self Tapping 4mm x 20mm Torx WP-T5/019
20 1 Bearing Cover for Top Bearing WP-T5/020
21 2 Machine Screw Cheese M4 x 89/45mm Pozi WP-T5/021
23 1 2 Core Cable c/w Gland with Plug 240V UK T5 V2 WP-T5/023A
1 2 Core Cable with Plug 115V UK T5L WP-T5L/023
1 2 Core Cable with Plug 230V Euro T5/EURO WP-T5EURO/023
24 1 Cable Guard WP-T5/024
25A 1 Switch Cover V2 WP-T5/025A
26A 1 Screw Self Tapping 4mm x 25mm Torx WP-T5/026A
28 1 Cable Clamp WP-T5/028
29A 1 Field Complete 240V T5E & T5/EURO V2 WP-T5E/029A
1 Field Complete 115V T5EL V2 WP-T5EL/029A
30 1 Deflector WP-T5/030
31A 1 Armature 240V with Fan T5 & T5/EURO V2 WP-T5E/031A
1 Armature 115V with Fan T5EL V2 WP-T5EL/031A
32 1 Carbon & Holder 240V T5 & T5/EURO (2 sets) WP-T5E/032
1 Carbon & Holder 115V T5EL (2 sets) WP-T5EL/032
33 2 Brush Clamp WP-T5/033
34 1 Guide Rods 8mm x 300mm (pair) ROD/8x300
35A 1 Top Bearing 8mm x 22mm x 7mm 6082RSI V2 WP-T5/035A
36 1 Slotted Round Nut WP-T5/036
37 1 Collet Nut <05/2005 CLT/NUT/T5
38 1 Threaded Pin M5 x 40mm Revolving Guide WP-T5/038
39A 1 Collet & Nut Set 6.35mm >05/2005 CNS/T5/635
0 Collet & Nut Set 6.0mm >05/2005 CNS/T5/6
0 Collet & Nut Set 8.0mm >05/2005 CNS/T5/8
40 1 Spanner 17mm A/F SPAN/17
Please use only Trend original spare parts.