TRENDnet TI-BG62i User manual

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
Table of Contents
i
Product Overview ...........................................................................2
TI-BG62i ......................................................................................................................... 2
Switch Installation ..........................................................................4
DIN-Rail Installation ....................................................................................................... 4
Install power supply connections .................................................................................. 5
SFP Transceiver/Optical Cable Installation .................................................................... 5
Basic IP Configuration.................................................................................................... 6
Connect additional devices to your switch.................................................................... 7
Accessing switch management interfaces........................................8
Access your switch command line interface.................................................................. 8
CLI Command Modes ......................................................................................................... 8
Access your switch web management page................................................................ 10
System Information.......................................................................11
Basic Settings................................................................................12
General Settings .......................................................................................................... 12
System.............................................................................................................................. 12
Static Route...................................................................................................................... 14
DNS Server ....................................................................................................................... 15
User Account ............................................................................................................... 15
System Time ................................................................................................................ 16
SSH............................................................................................................................... 19
Enable SSH (Secure Shell) management access ............................................................... 19
Telnet........................................................................................................................... 19
Enable SSH (Secure Shell) management access ............................................................... 19
System Log................................................................................................................... 19
SNMP ........................................................................................................................... 20
Group ............................................................................................................................... 22
SNMP User/Group............................................................................................................ 23
SNMP Trap ....................................................................................................................... 25
RMON Statistics........................................................................................................... 26
Mail Alarm ................................................................................................................... 26
Monitor........................................................................................28
Alarm ........................................................................................................................... 28
Port Utilization............................................................................................................. 29
SFP Information ........................................................................................................... 29
Traffic Monitor ............................................................................................................ 30
Hardware Information................................................................................................. 31
Modbus........................................................................................................................ 33
PTP (IEEE-1588 v2)....................................................................................................... 37
Auto Provision ............................................................................................................. 44
Physical Interface..........................................................................46
Port Settings ................................................................................................................ 46
General Settings............................................................................................................... 48
Spanning Tree Protocol ............................................................................................... 49
Link Aggregation.......................................................................................................... 56
Port Mirror................................................................................................................... 59
Loop Detection ............................................................................................................ 61
IGMP Snooping............................................................................................................ 63
IGMP Snooping ................................................................................................................ 63
MLD Snooping ............................................................................................................. 68
MVR............................................................................................................................. 69
Multicast Address ............................................................................................................ 72
Rate Limitation................................................................................................................. 74
GVRP............................................................................................................................ 76
VLAN ............................................................................................................................ 77

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
Table of Contents
ii
802.1Q VLAN.................................................................................................................... 77
Q-in-Q .......................................................................................................................... 81
Link Layer Discovery Protocol (LLDP)........................................................................... 88
MAC VLAN........................................................................................................................ 89
IP Subnet VLAN ................................................................................................................ 91
Dual Homing..................................................................................................................... 91
Xpress Ring....................................................................................................................... 91
Default Settings................................................................................................................ 92
Xpress-Ring Configurations:............................................................................................. 92
The global Xpress Ring state is: Disabled. ........................................................................ 92
Ring 1: State : Disabled. ................................................................................................... 92
Destination MAC : 01:80:c2:ff:ff:f0. ................................................................................. 92
Role : Forwarder............................................................................................................... 92
Primary Port : None. ........................................................................................................ 92
Secondary Port : None. .................................................................................................... 92
Ring 2: State : Disabled. ................................................................................................... 92
Destination MAC : 01:80:c2:ff:ff:f1. ................................................................................. 92
Role : Forwarder............................................................................................................... 92
Primary Port : None. ........................................................................................................ 92
Secondary Port : None. .................................................................................................... 92
Notices ............................................................................................................................. 93
Port Isolation.................................................................................................................... 93
Toplogy Map................................................................................................................ 94
ERPS (Ethernet Ring Protection Switching) ................................................................. 96
QoS ............................................................................................................................ 100
Power over Ethernet ...................................................................107
Port Security .............................................................................................................. 112
IP Source Guard ......................................................................................................... 114
DHCP Options ............................................................................................................ 120
DHCP Relay ................................................................................................................ 123
ARP Inspection ............................................................................................................... 125
Filter Table ..................................................................................................................... 127
Access Control List (ACL) ........................................................................................... 129
802.1x ........................................................................................................................ 133
TACACS+ .................................................................................................................... 139
Tools........................................................................................... 140
Firmware Upgrade..................................................................................................... 140
Configuration............................................................................................................. 140
Ping............................................................................................................................ 141
Ping Watchdog .......................................................................................................... 142
Technical Specifications ..............................................................143
TI-BG262i ................................................................................................................... 143
Troubleshooting ......................................................................... 146
Appendix....................................................................................147

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TI-BG62i
2
Product Overview
TI-BG62i
Front View
•PoE++ Ports 1-4 –Connect either network PoE++ or non-PoE devices.
•SFP Slot 5-6 –Designed to operate at Gigabit or 100Mbps speeds.
•Reset Button –Push the button for 5-10 seconds and release to reset.
•Grounding point/screw –The switch chassis can also be connected to a known
ground point for additional safety and protection. (grounding wire not
included)
Top View
*Please note power supply is sold separately*
**Supported power supplies: TI-S12024 (120W), TI-S24048 (240W), TI-S48048 (480W).
Lower wattage power supplies may be used but may result in decreased PoE power
budget**
LED Indicators
PoE+ + Gigabit
RJ-45 ports
10/100/1000
Mbps per port
LED indicator
LINK/ACT per
port LED
indicator
IP30 Rated
Housing
DIP Switches
Reboot Button
Ground point
6-pin terminal
block (PWR,
RPS, ALM)
DIP switch
definition
PoE LEDs
SFP Slots
4-pin terminal
block

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TI-BG62i
3
6-pin Removable Terminal Block
Note: Turn off the power before connecting modules or wires.
Calculate the maximum possible current in each power wire and common wire. Observe
all electrical codes dictating the maximum current allowable for each wire size. If current
go above the maximum ratings, the wiring could overheat, causing serious damage to
your equipment.
ALM DIP Switches
Switch
Status
Function
1
OFF
Disable alarm relay for PWR power input
ON
Enable alarm relay for power failure on PWR power input
2
OFF
Disable alarm relay for RPS power input
ON
Enable alarm relay for power failure on RPS power input
Input/Output
Function
PWR Input
(+) & (-)
Connects primary power source (ex. external power supply) to power the
device. Device will obtain power from this input first priority if available.
Please make sure to power supplies are turned off before wiring in.
Use a flat-head screw driver to push the orange notches in order release
the wiring connections. While holding in released position, insert the
wiring into the connection inputs from the external power supply and
release the orange notch to lock in the wire connections.
Device supports overload current protection and reverse polarity
protection.
RPS Input
(+) & (-)
Connects redundant power source (ex. external power supply) to power
the device. Device will obtain power from this input secondary priority if
primary power input is not available or has failed.
Please make sure to power supplies are turned off before wiring in.
Use a flat-head screw driver to push the orange notches in order release
the wiring connections. While holding in released position, insert the
wiring into the connection inputs from the external power supply and
release the orange notch to lock in the wire connections.
Device supports overload current protection and reverse polarity
protection.
ALM Output
Connects external alarm and sends output signal if fault is detected
based on DIP switch settings.
Supports an output with current carrying capacity of 1A @ 24V DC.

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TI-BG62i
4
Switch Installation
DIN-Rail Installation
The site where the switch will be installed may greatly affect its performance. When
installing, consider the following pointers:
Note: The switch model may be different than the one shown in the example
illustrations.
•Install the switch in the appropriate location. Please refer to the technical
specifications at the end of this manual for the acceptable operating temperature
and humidity ranges.
•Install the Switch in a site free from strong electromagnetic field generators (such
as motors), vibration, dust, and direct exposure to sunlight.
•Install the switch in a location that is not affected by strong electromagnetic field
generators (such as motors), vibration, dust, and direct sunlight.
•Leave at least 10cm of space at the front and rear of the switch for ventilation.
Fasten the DIN-Rail bracket to the rear of the switch using the included
fasteners/screws.
Note: The DIN-Rail bracket may already be installed to your switch when received.
The movable clip at the top of the DIN-Rail bracket should be on top.
The switch can be installed to a 35mm (W) DIN-Rail located in cabinet, rack, or
enclosure.
To mount the switch to a DIN-Rail using the attached DIN-Rail bracket, position the
switch in front of the DIN-Rail and hook the bracket over the top of the rail.
Then rotate the switch downward towards the rail until your hear a click indicating the
bracket is secure and locked into place.
To unmount the switch from the DIN-Rail, slightly pull the switch downwards to clear
the bottom of the DIN-Rail and rotate away from DIN-Rail to unmount.

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TI-BG62i
5
Install power supply connections
Connect the power supply (sold separate, e.g. TRENDnet TI-S24048) to the switch
terminal block as shown below.
Optional: The switch chassis can also be connected to a known ground point for
additional safety and protection (grounding wire not included).
Note: Polarities V+ and V- should match between power supply and connections to
switch terminal block.
Note: The models in the image may be different than your specific model.
SFP Transceiver/Optical Cable Installation
1. Remove the rubber plug from the SFP slot.
Note: For any unused ports or SFP slots, it is recommended to leave the
rubber plugs installed during operation.
2. Slide the selected SFP module into the selected SFP slot (Make sure the SFP
module is aligned correctly with the inside of the slot)
3. Insert and slide the module into the SFP slot until it clicks into place.
4. Remove any rubber plugs that may be present in the SFP module’s slot.
5. Align the fiber cable’s connector with the SFP module’s mouth and insert the
connector
6. Slide the connector in until a click is heard
7. If you want to pull the connector out, first push down the release clip on top
of the connector to release the connector from the SFP module
To properly connect fiber cabling:Check that the fiber terminators are clean. You can
clean the cable plugs by wiping them gently with a clean tissue or cotton ball moistened
with a little ethanol. Dirty fiber terminators on fiber optic cables will impair the quality of
the light transmitted through the cable and lead to degraded performance on the port.
Note: When inserting the cable, be sure the tab on the plug clicks into position to
ensure that it is properly seated.

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TI-BG62i
6
Basic IP Configuration
2. Assign a static IP address to your computer’s network adapter in the subnet of
192.168.10.x (e.g. 192.168.10.25) and a subnet mask of 255.255.255.0.
3. Open your web browser, and type the IP address of the switch in the address bar, and
then press Enter. The default IP address is 192.168.10.200.
4. Enter the User Name and Password, and then click Login. By default:
User Name: admin
Password: admin
Note: User name and password are case sensitive.
5. Click System, click L3 Feature, and then click IP Interface.
6. Configure the switch IP address settings to be within your network subnet, then click
Apply.
Note: You may need to modify the static IP address settings of your computer’s network
adapter to IP address settings within your subnet in order to regain access to the switch
.
7. Click Save at the top right.
8. When confirmation message appears click OK.
Note: Once the settings are saved, you can connect the switch to your network.

© Copyright 2023 TRENDnet. All Rights Reserved.
7
TRENDnet User’s Guide
TI-BG62i
Connect additional devices to your switch
You can connect additional computers or other network devices to your switch using Ethernet cables to connect them to one of the available Gigabit Ports. Check the status of the LED
indicators on the front panel of your switch to ensure the physical cable connection from your computer or device.
Note: If you encounter issues connecting to your network, there may be a problem with your computer or device network settings. Please ensure that your computer or device network
settings (also called TCP/IP settings) are configured properly within the network subnet your switch is connected.
Note: The switch below may be different than the one you purchased.

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TI-BG62i
8
Accessing switch management interfaces
Access your switch command line interface
Note: The system may be managed using the Telnet protocol. The Telnet protocol is
enabled by default. Throughout this user’s guide, the term “CLI Configuration” will be
used reference access through the command line interface.
1. Connect your computer to one of the available Ethernet ports and make sure your
computer and switch are assigned to an IP address with the same IP subnet.
2. On your computer, run the terminal emulation program (ex. HyperTerminal,
TeraTerm, Putty, etc.) and set the program to use the Telnet protocol and enter the IP
address assigned to the switch. The default IP address of the switch is 192.168.10.200
/ 255.255.255.0.
3. The terminal emulation window should display a prompt for user name and
password.
Enter the user name and password. By default:
Console User Name: admin
Note: User Name and Password are case sensitive.
Enable Mode/Privileged Exec User Name: admin
Enable Mode/Privileged Exec Password: admin
Setting
Default Value
Default Username
admin
Default Password
admin
Setting
Default Value
IP Address
192.168.10.200
Subnet Mask
255.255.255.0
Default Gateway
0.0.0.0
Management VLAN
1
Default Username
admin
Default Password
admin
CLI Command Modes
Node
Command
Description
enable
show hostname
This command displays the system’s network
name.
configure
reboot
This command reboots the system.
eth0
ip address A.B.C.D/M
This command configures a static IP and subnet
mask for the system.
interface
show
This command displays the current port
configurations.
vlan
show
This command displays the current VLAN
configurations.

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TI-BG62i
9
The Node type:
⚫enable
Its command prompt is “[DEVICE_NAME]#”.
It means these commands can be executed in this command prompt.
⚫configure
Its command prompt is “[DEVICE_NAME](config)#”.
It means these commands can be executed in this command prompt.
In Enable code, executing command “configure terminal” enter the configure
node.
[DEVICE_NAME]# configure terminal
⚫eth0
Its command prompt is “[DEVICE_NAME](config-if)#”.
It means these commands can be executed in this command prompt.
In Configure code, executing command “interface eth0” enter the eth0
interface node.
[DEVICE_NAME](config)#interface eth0
[DEVICE_NAME](config-if)#
⚫interface
Its command prompt is “[DEVICE_NAME](config-if)#”.
It means these commands can be executed in this command prompt.
In Configure code, executing command “interface gigaethernet1/0/5” enter
the interface port 5 node.
Or
In Configure code, executing command “interface fastethernet1/0/5” enter
the interface port 5 node.
Note: depend on your port speed, gigaethernet1/0/5 for gigabit Ethernet
ports and fastethernet1/0/5 for fast Ethernet ports.
[DEVICE_NAME](config)#interface gigaethernet1/0/5
[DEVICE_NAME](config-if)#
⚫vlan
Its command prompt is “[DEVICE_NAME](config-vlan)#”.
It means these commands can be executed in this command prompt.
In Configure code, executing command “vlan 2” enter the vlan 2 node.
Note: where the “2” is the vlan ID.
[DEVICE_NAME](config)#vlan 2
[DEVICE_NAME](config-vlan)#

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TI-BG62i
10
Access your switch web management page
Note: Your switch default management IP address http://192.168.10.200 is accessed
through the use of your Internet web browser (e.g. Internet Explorer®, Firefox®,
Chrome™, Safari®, Opera™) and will be referenced frequently in this User’s Guide.
Throughout this user’s guide, the term Web Configuration will be used to reference
access from web management page.
1. Open your web browser and go to the IP address http://192.168.10.200. Your switch
will prompt you for a user name and password.
2. Enter the user name and password. By default:
User Name: admin
Password: admin
Note: User Name and Password are case sensitive.
Parameter
Description
User Name
Enter the user name.
Password
Enter the password.

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TI-BG62i
11
System Information
CLI Configuration
Node
Command
Description
enable
show hostname
This command displays the system’s network
name.
enable
show interface eth0
This command displays the current Eth0
configurations.
enable
show model
This command displays the system information.
enable
show running-config
This command displays the current operating
configurations.
enable
show system-info
This command displays the system’s CPU loading
and memory information.
enable
show uptime
This command displays the system up time.
Web Configuration
Dashboard > Dashboard
Parameter
Description
System Uptime
This field displays the total time the switch has been on
Runtime Image
This field displays the firmware version of the switch
Boot Loader
This field displays the boot code version.
DRAM Size
The total size of the RAM
Flash Size
This field displays the total size of the Flash.
Temperature
This field displays the current temperature of the switch.
System Name
This field displays the name of the Switch.
System Location
This field displays the location of the switch.
System Contact
This field displays the contact information of the switch.
Serial Number
The serial number assigned by manufacture for identification of
the unit.
MAC Address
This field displays the MAC (Media Access Control) address of the
Switch.
IP Address
This field indicates the IP address of the Switch.
Subnet Mask
This field indicates the subnet mask of the Switch.
Default Gateway
This field indicates the default gateway of the Switch.
IPv6 Unicast
Address / Prefix
Length
This field indicates the IPv6 Unicast Address.
IPv6 Default
Gateway
This field displays the gateway’s IPv6 Address.
Link Local Address
/ Prefix Length
This field displays the local IPv6 Address
IPv4 DHCP Client
Mode
This field displays whether the IPv4 DHCP client is enabled on the
Switch.
IPv6 DHCP Client
Mode
This field displays whether the IPv6 DHCP client is enabled on the
Switch.

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TI-BG62i
12
Parameter
Description
Total
This field displays the max budget for PoE in Watts
Used
This field displays the current total wattage used for PoE in Watts
Parameter
Description
CPU Used
This field displays the amount of CPU resources being used
Memory Used
This field displays the amount of memory being used
Switch View
Dashboard > Switch View
Parameter
Description
Throughput
This field displays the current throughput of the port.
Loopback
Detection
This field displays the current status of Loopback Detection.
PoE On/Off
Enable and disable the PoE of the connected PD device.
Device Type
This field displays the current type of device connected to this
port.
PoE Status
Displays the current PoE status.
PoE Standard
Displays the PoE standard being used.
Power
Consumption
Displays the max power consumption in used by the PD device.
Basic Settings
General Settings
System
Management VLAN
To specify a VLAN group which can access the Switch.
⚫The valid VLAN range is from 1 to 4094.
⚫If you want to configure a management VLAN, the management VLAN should
be created first and the management VLAN should have at least one member
port.

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TI-BG62i
13
Host Name
The hostname is same as the SNMP system name. Its length is up to 64 characters.
The first 16 characters of the hostname will be configured as the CLI prompt.
Default Settings
The default Hostname is [YOUR_DEVICE_NAME]
The default DHCP client is disabled.
The default Static IP is 192.168.10.200
Subnet Mask is 255.255.255.0
Default Gateway is 0.0.0.0
Management VLAN is 1.
CLI Commands
Node
Command
Description
configure
Reboot
This command reboots the system.
configure
hostname STRINGS
This command sets the system's network
name.
configure
interface eth0
This command enters the eth0 interface
node to configure the system IP.
eth0
Show
This command displays the eth0
configurations.
eth0
ip address A.B.C.D/M
This command configures a static IP and
subnet mask for the system.
eth0
ip address default-
gateway A.B.C.D
This command configures the system
default gateway.
eth0
ip dhcp client
(disable|enable|renew)
This command configures a DHCP client
function for the system.
Disable: Use a static IP address on the
switch.
Enable & Renew: Use DHCP client to get an
IP address from DHCP server.
eth0
management vlan
VLANID
This command configures the management
vlan.
Example: The procedures to configure an IP address for the Switch.
✓To enter the configure node.
[DEVICE_NAME]#configure terminal
[DEVICE_NAME](config)#
✓To enter the ETH0 interface node.
[DEVICE_NAME](config)#interface eth0
[DEVICE_NAME](config-if)#
✓To get an IP address from a DHCP server.
[DEVICE_NAME](config-if)#ip dhcp client enable
✓To configure a static IP address and a gateway for the Switch.
[DEVICE_NAME](config-if)#ip address 192.168.202.111/24
[DEVICE_NAME](config-if)#ip address default-gateway 192.168.202.1
Web Configuration
System > L3 Feature > IP Interface

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TI-BG62i
14
DHCP Client
Sets the switch to DHCP client to receive IP address assigned by
the default gateway.
IP Address
Configures a IPv4 address for your Switch in dotted decimal
notation. For example, 192.168.10.200.
Subnet Mask
Enter the IP subnet mask of your Switch in dotted decimal
notation for example 255.255.255.0.
Default Gateway
Enter the IP address of the default outgoing gateway in dotted
decimal notation, for example 192.168.10.1.
DHCPv6 Client
Sets the switch to enable or disable DHCPv6 client to receive IP
address assigned by the default gateway.
Global Address
Configures a IPv6 address for your Switch in dotted decimal
notation.
Default Gateway
Enter the default IPv6 address for your gateway
Static Route
System > L3 Feature > Static Route
IP Forwarding
Configures the switch to enable or disable IP Forwarding.
IP ARP Proxy
Configures the switch to enable or disable IP ARP Proxy.
IPv4 ARP Table
Configures the switch to add or delete the IPv4 ARP table.
IP
Enter the IP address for the static route.
MAC
Enter the MAC address for the static route.
IPv6 ARP Table
Configures the switch to add or delete the IPv6 ARP table.
IP
Enter the IPv6 IP address for the IPv6 ARP table.
MAC
Enter the MAC address for the IPv6 ARP table.

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TI-BG62i
15
VLAN
Enter the VLAN ID to route
IPv4
Add or delete the settings.
IP/M
Gateway
Enter the Gateway address
IPv6
Add or delete the settings for the IPv6
IP/M
Gateway
Enter the IPv6 gateway address
DNS Server
System > DNS
DNS IPv4 Server
Enter the IP address of the DNS server.
Note: DNS is set to 8.8.8.8 and 8.8.4.4 by default
DNS IPv6 Server
Enter the IP address in IPv6 of the DNS server
User Account
The Switch allows users to create up to 6 user account. The user name and the password
should be the combination of the digit or the alphabet. The last admin user account
cannot be deleted. Users should input a valid user account to login the CLI or web
management.
User Authority:
The Switch supports two types of the user account, admin and normal. The default user’s
account is username (admin) / password (admin).
⚫admin - read / write.
⚫normal - read only.
; Cannot enter the privileged mode in CLI.
; Cannot apply any configurations in web.
The Switch also supports backdoor user account. In case of that user forgot their user
name or password, the Switch can generate a backdoor account with the system’s MAC.
Users can use the new user account to enter the Switch and then create a new user
account.
Default Settings
Maximum user account : 6.
Maximum user name length : 32.
Maximum password length : 32.
Default user account for privileged mode : admin / admin.
Notices
The Switch allows users to create up to 6 user account.
The user name and the password should be the combination of the digit or the
alphabet.
The last admin user account cannot be deleted.
The maximum length of the username and password is 32 characters.
CLI Configuration
Node
Command
Description
enable
show user account
This command displays the current user
accounts.

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TI-BG62i
16
configure
add user USER_ACCOUNT
PASSWORD
(normal|admin)
This command adds a new user account.
configure
delete user
USER_ACCOUNT
This command deletes a present user
account.
Example:
[DEVICE_NAME]#configure terminal
[DEVICE_NAME](config)#add user q q admin
[DEVICE_NAME](config)#add user 1 1 normal
Web Configuration
System > Administration
Parameter
Description
User Name
Type a new username or modify an existing one.
User Password
Type a new password or modify an existing one. Enter up to 32
alphanumeric or digit characters.
User Authority
Select with which group the user associates: admin (read and
write) or normal (read only) for this user account.
Add
Click Add to add/modify the user account.
Refresh
Click Refresh to begin configuring this screen afresh.
Administration Table
Index.
This field displays the index number of an entry.
User Name
This field displays the name of a user account.
User
Authority
This field displays the associated group.
Action
Click the Delete button to remove the user account.
Note: You cannot delete the last admin accounts.
System Time
The Network Time Protocol (NTP) is a protocol for synchronizing the clocks of computer
systems over packet-switched, variable-latency data networks. A less complex
implementation of NTP, using the same protocol but without requiring the storage of
state over extended periods of time is known as the Simple Network Time Protocol
(SNTP). NTP provides Coordinated Universal Time (UTC). No information about time
zones or daylight saving time is transmitted; this information is outside its scope and must
be obtained separately.
UDP Port: 123.
Daylight saving is a period from late spring to early fall when many countries set their
clocks ahead of normal local time by one hour to give more daytime light in the evening.
Note:
1. The SNTP server always replies the UTC current time.
2. When the Switch receives the SNTP reply time, the Switch will adjust the time
with the time zone configuration and then configure the time to the Switch.
3. If the time server’s IP address is not configured, the Switch will not send any
SNTP request packets.
4. If no SNTP reply packets, the Switch will retry every 10 seconds forever.
5. If the Switch has received SNTP reply, the Switch will re-get the time from NTP
server every 24 hours.
6. If the time zone and time NTP server have been changed, the Switch will
repeat the query process.
7. No default SNTP server.

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TI-BG62i
17
Default Settings
Current Time:
-----------------------------------------------
Time: 0:3:51 (UTC)
Date: 1970-1-1
Time Server Configuration:
-----------------------------------------------
Time Zone : +00:00
IP Address: 0.0.0.0
DayLight Saving Time Configuration:
-----------------------------------------------
State : disabled
Start Date: None.
End Date : None.
CLI Configuration
Node
Command
Description
enable
show time
This command displays current time
and time configurations.
configure
time HOUR:MINUTE:SECOND
Sets the current time on the Switch.
hour: 0-23
min: 0-59
sec: 0-59
Note: If you configure Daylight Saving
Time
after you configure the time, the
Switch will apply Daylight Saving Time.
configure
time date YEAR/MONTH/DAY
Sets the current date on the Switch.
year: 1970-
month: 1-12
day: 1-31
configure
time daylight-saving-time
This command enables the daylight
saving time.
configure
time daylight-saving-time
start-date (first | second |
third | fourth | last) (Sunday
| Monday | Tuesday |
Wednesday | Thursday |
Friday | Saturday) MONTH
OCLOCK
This command sets the start date for
the Daylight Saving Time.
For Example: first Sunday 4 0 (AM:0 1st
Sunday in April)
configure
time daylight-saving-time
end-date (first | second |
third | fourth | last) (Sunday
| Monday | Tuesday |
Wednesday | Thursday |
Friday | Saturday) MONTH
OCLOCK
This command sets the end date for
the Daylight Saving Time.
For Example: Last Sunday 10 18 (PM: 6
Last Sunday in October)
configure
no time daylight-saving-time
This command disables daylight saving
on the Switch.
configure
time ntp-server IP_ADDRESS
This command sets the IP address of
your time server.
configure
no time ntp-server
This command disables the NTP server
settings.
configure
time timezone VALUE
Selects the time difference between
UTC (formerly known as GMT) and your
time zone.
Valid value: -1200 to 1200.
Example:
[DEVICE_NAME](config)#time ntp-server 192.5.41.41
[DEVICE_NAME](config)#time timezone +0800

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TI-BG62i
18
[DEVICE_NAME](config)#time ntp-server enable
[DEVICE_NAME](config)#time daylight-saving-time start-date first Monday 6 0
[DEVICE_NAME](config)#time daylight-saving-time end-date last Saturday 10 0
Web Configuration
System > System Time
Parameter
Description
Current Time and Date
Current Time
This field displays the time you open / refresh this menu.
Current Date
This field displays the date you open / refresh this menu.
Time and Date Setting
Manual
Select this option if you want to enter the system date and time
manually.
New Time
Enter the new date in year, month and day format and time in
hour, minute and second format. The new date and time then
appear in the Current Date and Current Time fields after you click
Apply.
Enable
Network Time
Protocol
Select this option to use Network Time Protocol (NTP) for the time
service.
NTP Server
Select a pre-designated time server or type the IP address or type
the domain name of your time server. The Switch searches for the
timeserver for up to 60 seconds.
Time Zone
Select the time difference between UTC (Universal Time
Coordinated, formerly known as GMT, Greenwich Mean Time)
and your time zone from the drop-down list box.
Daylight Saving Settings
State
Select Enable if you want to use Daylight Saving Time. Otherwise,
select Disable to turn it off.
Start Date
Configure the day and time when Daylight Saving Time starts if you
enabled Daylight Saving Time. The time is displayed in the 24 hour
format. Here are a couple of examples:
Daylight Saving Time starts in most parts of the United States on
the second Sunday of March. Each time zone in the United States
starts using Daylight Saving Time at 2 A.M. local time. So in the
United States you would select Second, Sunday, March and 2:00.
Daylight Saving Time starts in the European Union on the last
Sunday of March. All of the time zones in the European Union start
using Daylight Saving Time at the same moment (1 A.M. GMT or
UTC). So in the European Union you would select Last, Sunday,
March and the last field depends on your time zone. In Germany
for instance, you would select 2:00 because Germany's time zone
is one hour ahead of GMT or UTC (GMT+1).
End Date
Configure the day and time when Daylight Saving Time ends if you
enabled Daylight Saving Time. The time field uses the 24 hour
format.
Here are a couple of examples: