TRENDnet TEW-816DRM User manual

TRENDnet User’s Guide
Cover Page

© Copyright 2014 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
Table of Contents
i
Contents
Product Overview ...........................................................................1
Package Contents .......................................................................................................... 1
Features......................................................................................................................... 1
Product Hardware Features........................................................................................... 2
Basic Router Setup ..........................................................................5
Creating a Home Network ............................................................................................. 5
Router Installation ......................................................................................................... 6
Connect additional wired devices to your network....................................................... 9
Wireless Networking and Security .................................................10
How to choose the type of security for your wireless network .................................. 10
Secure your wireless network ..................................................................................... 11
Connect wireless devices to your router ..................................................................... 12
Connect wireless devices using WPS ........................................................................... 13
Basic wireless settings ................................................................................................. 14
Guest Network............................................................................................................. 15
Steps to improve wireless connectivity ....................................................................... 16
Advanced wireless settings.......................................................................................... 16
Multiple SSID ........................................................................................................... 16
Additional Wireless Settings ................................................................................... 17
Wireless bridging using WDS (Wireless Distribution System)................................. 17
Access Control Filters ....................................................................19
Access control basics ................................................................................................... 19
Wireless MAC address filters .................................................................................. 19
MAC address filters ................................................................................................. 19
URL/Keyword Blocking ............................................................................................ 20
IP Filtering ............................................................................................................... 21
Packet Filters ............................................................................................................... 21
Advanced Router Setup ................................................................ 23
Access your router management page........................................................................ 23
Change your router login password ............................................................................ 24
Set your router date and time..................................................................................... 24
Manually configure your Internet connection ............................................................ 25
Change your router IP address .................................................................................... 29
Set up the DHCP server on your router ....................................................................... 29
Assign specific IP address to clients............................................................................. 30
Enable/disable UPnP on your router........................................................................... 30
Configure ALG settings ................................................................................................ 31
Additional Security Settings......................................................................................... 32
Allow/deny multicast streaming.................................................................................. 32
Identify your network on the Internet ........................................................................ 34
Allow remote access to your router management page ............................................. 34
Open a device on your network to the Internet.......................................................... 35
DMZ......................................................................................................................... 35
Port Forwarding ...................................................................................................... 35
Port Trigger ............................................................................................................. 36
Prioritize traffic using QoS (Quality of Service) ........................................................... 37
Add static routes to your router.................................................................................. 39
Enable dynamic routing on your router ...................................................................... 40
Setup Port Mapping..................................................................................................... 40
Setup IPv6 on your router ........................................................................................... 41
Configure ADSL settings............................................................................................... 41
Using External USB Storage ...........................................................42

© Copyright 2014 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
Table of Contents
ii
File Sharing Server ....................................................................................................... 42
FTP (File Transfer Protocol) Server .............................................................................. 43
Using 3G WAN Connection ............................................................43
Configure 3G WAN....................................................................................................... 44
Router Maintenance & Monitoring................................................44
Reset your router to factory defaults .......................................................................... 44
Router Default Settings ............................................................................................... 45
Backup and restore your router configuration settings .............................................. 45
Restart your router ...................................................................................................... 47
Check connectivity using the router management page............................................. 47
Manage Initialization Scripts ....................................................................................... 47
Check Internet connectivity using the router management page............................... 48
Check the router system information.......................................................................... 48
Check the router IPv6 status........................................................................................ 50
Check the router IPv6 status........................................................................................ 50
Check the router Wireless clients................................................................................ 50
Check the router LAN clients ....................................................................................... 51
Check the router Routing Table................................................................................... 51
Check the router Basic Statistics.................................................................................. 51
Check the router DSL Statistics.................................................................................... 51
View your router log.................................................................................................... 52
View your router traffic ............................................................................................... 52
Configure your router log ............................................................................................ 53
Enable SNMP on your router....................................................................................... 53
Enable TR-069 on your router ..................................................................................... 53
Trusted Certificates ..................................................................................................... 54
Troubleshooting ...........................................................................55
Appendix ......................................................................................56

© Copyright 2013 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-816DRM
1
Product Overview
TEW-816DRM
Package Contents
In addition to your router, the package includes:
TEW-816DRM
Quick Installation Guide
CD-ROM (User’s Guide)
Network cable (1.5 m/5 ft.)
RJ11 telephone cable (1 m/3 ft.)
Power adapter (12 V DC, 1.5 A)
If any package contents are missing or damaged, please contact the retail store, online
retailer, or reseller/distributor from which the product was purchased.
Features
TRENDnet’s AC750 Wireless VDSL2/ADSL2+ Modem Router, model TEW-816DRM, offers
a combination high performance modem for internet access and a powerful wireless
AC750 router. The built-in modem supports the latest ADSL2+ and VDSL2 standards for
downstream speeds of up to 200 Mbps*. Wireless AC750 produces concurrent high
speed 433 Mbps Wireless AC and 300 Mbps Wireless N networks. Use the two USB and
four Ethernet ports to share content and devices across the network.
Features
Easy Setup
Get up and running quickly with the intuitive guided setup
VDSL Internet Service
Compatible with VDSL2 internet service provider networks (Profile 8a, 8b, 8c, 8d, 12a,
12b, 17a, and 30a support) for downstream throughput of up to 200 Mbps*
ADSL Internet Service
Compatible with ADSL 2/2+ internet service provider networks (ADSL 2/2+ and Annex A,
B, I, J, L, and M support)*
Wireless AC750
Concurrent high speed 433 Mbps Wireless AC + 300 Mbps Wireless N bands
Pre-Encrypted Wireless
For your convenience the wireless network arrives pre-encrypted with its own unique
password
One Touch Connection
Connect to the router at the touch of the Wi-Fi Protected Setup (WPS) button
Ethernet Ports
Four Ethernet ports to connect wired devices
USB Share Ports
Plug in flash or storage drives to the two high speed USB ports to share content across
the network
Parental Controls
Control access to specific websites and manage which devices can access the router

© Copyright 2013 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-816DRM
2
Remote Management
Remote management and troubleshooting support with TR-069
3G WAN Backup
3G WAN backup support
IPv6
IPv6 network support
On/Off Power Button
Convenient on/off power button
*Maximum wireless signal rates are referenced from IEEE 802.11 theoretical specifications. Actual
data throughput and coverage will vary depending on interference, network traffic, building
materials and other conditions.
Product Hardware Features
Rear View
VDSL/ADSL Port: Connect an RJ-11 telephone cable from your modem router ADSL
WAN port to your telephone jack/DSL line.
LAN Ports: Connect Network cables (also called network cables) from your modem
router LAN ports to your wired network devices.
10/100 WAN Port: Connect an RJ-45 cable when not using VDSL/ADSL WAN
connection.
Reset Button: Push and hold this button for 10 seconds and release to reset your
router to its factory defaults.
USB Port: Connect a USB device to share files within your network
Power Port: Connect the included power adapter from your modem router power
port and to an available power outlet.
VDSL/ADSL
Port
Power
Port
LAN Ports
Reset
Button
USB Port
10/100 WAN Port

© Copyright 2013 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-816DRM
3
Front View
Power LED: This LED indicator is blinks green when properly connected to a power
supply. When the device is malfunctioned LED indicator will be red.
Internet LED: This LED indicator is blinking green when the ADSL status of the
modem router is ready to establish connection to your ISP. The LED indicator will
turn solid green when the modem router has been properly configured with the
settings provided by your ISP and successful ADSL connection has been made to
your ISP. This LED indicator will be blink while data is transmitted or received
through the ADSL port of your modem router.
WAN LED: This LED Indicator is solid green with valid internet connection. The LD
indicator blinks green during data transmission. If the indicator is red, this indicates
invalid internet connection.
LAN 1-4 (Link/Activity) LEDs –These LED indicators are solid green when the LAN
ports are successfully connected to your wired network devices (which are turned
on). These LED indicators will blink green while data is transmitted or received
through your modem router’s LAN ports.
2.4GHz Wireless LED: This LED indicator is solid green when the wireless is “On”
and functioning properly on your modem router. This LED indicator will be blinking
while data is transmitted or received by your wireless clients or wireless network
devices connected to your modem router. This LED indicator will be off when the
wireless functionality of your modem router is disabled.
5GHz Wireless LED: This LED indicator is solid green when the wireless is “On” and
functioning properly on your modem router. This LED indicator will be blinking
while data is transmitted or received by your wireless clients or wireless network
devices connected to your modem router. This LED indicator will be off when the
wireless functionality of your modem router is disabled.
WPS LED: This LED indicator blinks green when WPS is activated. The LED will stop
blinking and remain solid when WPS is completed. When the indicator blinks red it
indicates there was no WPS device connected.
USB1/2: This LED indicator blinks green when a device is connected to the USB port.
Diagnostic LEDs

© Copyright 2013 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-816DRM
4
Side View
v
Wireless On/Off and WPS Button: Push button and hold the button down to 10
seconds to turn off the wireless radio. To turn on the wireless radio push and hold
down the button for another 10 seconds. To activate WPS to activate WPS (WiFi
Protected Setup) push and hold the button for 3 seconds and release to activate
WPS. Within 2 minutes, push and hold the WPS button on your wireless client
device.
USB Port: Connect a USB device to share files within your network
On/Off Button: Press to on or off the device.
On/Off Button
USB Port
Wireless On/Off and
WPS Button

© Copyright 2014 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-816DRM
5
Basic Router Setup
Creating a Home Network
What is a network?
A network is a group of computers or devices that can communicate with each other. A
home network of more than one computer or device also typically includes Internet
access, which requires a router.
A typical home network may include multiple computers, a media player/server, a
printer, a modem, and a router. A large home network may also have a switch,
additional routers, access points, and many Internet-capable media devices such as TVs,
game consoles, and Internet cameras.
Modem: Connects a computer or router to the Internet or ISP (Internet Service
Provider).
Note: The TEW-816DRM is a combination DSL modem and router, therefore, you do
not require a separate DSL modem from your ISP when setting up this product.
Router: Connects multiple devices to the Internet.
Switch: Connect several wired network devices to your home network. Your router
has a built-in network switch (the LAN port 1-4). If you have more wired network
devices than available Network ports on your router, you will need an additional
switch to add more wired connections.
How to set up a home network
1. For a network that includes Internet access, you’ll need:
Computers/devices with a Network port or wireless networking capabilities.
A modem and Internet service to your home, provided by your ISP (modem typically
supplied by your ISP).
A router to connect multiple devices to the Internet.
2. Set up your router. See “How to setup your router” below.
3. To connect additional wired computers or wired network devices to your network,
see “Connect additional wired devices to your network” on page 11.
4. To set up wireless networking on your router, see “Wireless Networking and Security”
on page 10.
How to setup your router
Refer to the Quick Installation Guide or continue to the next section “Router
Installation” on page 6 for more detailed installation instructions.
Where to find more help
In addition to this User’s Guide, you can find help below:
http://www.trendnet.com/support
(documents, downloads, and FAQs are available from this Web page))

© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-816DRM
6
Router Installation
Before you Install
Many Internet Service Providers (ISPs) allow your router to connect to the Internet
without verifying the information fields listed below. Skip this section for now and if
your router cannot connect to the Internet using the standard installation process, come
back to this page and contact your ISP to verify required ISP specification fields listed
below.
General ADSL Parameters
VCI: ____
VPI: ____
MTU: ________
Data Encapsulation (LLC/VCMux) : _________
Schedule Type (UBR/CBR/VBR/GFR): _______
VLAN Tag (If required by your ISP): _________
ADSL Connection Types:
1. Ethernet over ATM (RFC 1483 Bridged) with NAT
1a. Obtain IP Address Automatically (Dynamic IP Address)
Host Name (Optional) ______________________
ISP registered Mac Address or Clone MAC address (Optional)___:___:___:___:___:___
1b. Fixed IP address (Static IP Address)
WAN IP Address: _____. _____._____._____ (e.g. 215.24.24.129)
WAN Subnet Mask: _____. _____._____._____
WAN Gateway IP Address: _____. _____._____._____
Primary DNS Server Address: _____. _____._____._____
Secondary DNS Server Address: _____. _____._____._____
2. IP over ATM (RFC 1483 Routed)
2a. Obtain IP Address Automatically (Dynamic IP Address)
Host Name (Optional) ______________________
ISP registered Mac Address or Clone MAC address (Optional)___:___:___:___:___:___
2b . Fixed IP address (Static IP Address)
WAN IP Address: _____. _____._____._____ (e.g. 215.24.24.129)
WAN Subnet Mask: _____. _____._____._____
WAN Gateway IP Address: _____. _____._____._____
Primary DNS Server Address: _____. _____._____._____
Secondary DNS Server Address: _____. _____._____._____
3. PPP over ATM (PPPoE)
3a. PPPoE to obtain IP automatically
Account/User Name: _________
Password: ________________
3b. PPPoE with a fixed IP address
User Name: _________
Password: ________________
Verify Password: ________________
IP Address: ____. _____._____._____ (e.g. 215.24.24.129)
Primary DNS Server Address: _____. _____._____._____
Secondary DNS Server Address: _____. _____._____._____
4. PPP over Ethernet (PPPoA)
4a. PPPoA to obtain IP automatically
Account/User Name: _________
Password: ________________
4b. PPPoA with a fixed IP address
User Name: _________
Password: ________________
Verify Password: ________________
IP Address: ____. _____._____._____ (e.g. 215.24.24.129)
Primary DNS Server Address: _____. _____._____._____
Secondary DNS Server Address: _____. _____._____._____

© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-816DRM
7
Hardware Installation
1. Connect the detachable antenna to your modem router.
2. Connect one end of the RJ-11 telephone cable to the modem router ADSL port.
Connect the other end of the RJ-11 telephone cable to the telephone jack/DSL line.
3. Using the Network cable, connect your computer to one of the four LAN ports on the
modem router.
4. Connect the power adapter to the modem router and then to a power outlet.
5. Verify that the status LED indicators on the front of the modem to confirm the device
is fully functional: Status (Green), ADSL (Green), WLAN (Green) and the LAN port
(1,2,3,4) (Green) your computer is connected.
Setup Wizard
1. Open your web browser (e.g. Internet Explorer, Firefox, Safari, Chrome, or Opera)
and go to http://192.168.10.1. Your router will prompt you for a user name and
password.
2. Your router will prompt you for a user name and password. For added security, the
router is preconfigured with a unique password. You can find the Password on a
sticker on the side of the router and on the label on the bottom of the router.
3. Enter your Username and Password, select your preferred language, and then click
Login.

© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-816DRM
8
3. Once logged into the router’s user interface click Setup Wizard under Setup section
on the left side of the interface.
4. Click on Setup Wizard to start the setup wizard installation.
5. Select the mode provided by your ISP (Internet Service Provider) and click Next to
continue. The example below is based on PPPoE type with an ADSL connection type.
Please contact your ISP (Internet Service Provider) if you uncertain your connection
type. l
6. Select your connection mode and click Next.
7. Select Auto-detect to have the router automatically detect your encapsulation
information. Or simply select Manual Selection option to manually enter your VPI/VCI
settings. Click Next to continue.
9. Once the router detects your VPI/VCI settings, select your country and ISP services. If
your ISP services it not listed, select Other. If you selected Manual Selection on the
previous step, you will need to enter your VPI/VCI settings on this section.
10. Enter your assigned Username and Password information from your ISP (Internet
Service Provider). Click Next to continue.

© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-816DRM
9
11. Verify your settings, and click Finish to completer the setup wizard.
Note: If you cannot access the Internet, please verify your hardware connections and
LED status and re-run the Setup Wizard to verify you have applied the correct settings.
12. For added security, the router is pre-encrypted with its own unique wireless network
security key. You can find the unique network security key and pre-assigned network
name (SSID) on a sticker on the front of the router and on a label on the bottom of the
router. If you would like to change the wireless settings, continue to the next page to
launch the wireless setup wizard.
Connect additional wired devices to your network
You can connect additional computers or other network enabled devices to your
network by using Network cables. Connect them to one of the available LAN ports
labeled 1,2,3,4 on your modem router. Check the status of the LED indicators (1, 2, 3, or
4) on the front panel of your router to ensure the physical cable connection from your
computer or device.
Note: If you encounter issues connecting to your network, there may be a problem with
your computer or device network settings. Please ensure that your computer or device
network settings (also called TCP/IP settings) are configured to obtain IP address settings
automatically (also called dynamic IP address or DHCP) and to Obtain DNS Server
address settings automatically.

© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-816DRM
10
Wireless Networking and Security
How to choose the type of security for your wireless network
Setting up wireless security is very important. Leaving your wireless network open and
unsecure could expose your entire network and personal files to outsiders. TRENDnet
recommends reading through this entire section and setting up wireless security on your
new router.
There are a few different wireless security types supported in wireless networking each
having its own characteristics which may be more suitable for your wireless network
taking into consideration compatibility, performance, as well as the security strength
along with using older wireless networking hardware (also called legacy hardware).
It is strongly recommended to enable wireless security to prevent unwanted users from
accessing your network and network resources (personal documents, media, etc.).
In general, it is recommended that you choose the security type with the highest
strength and performance supported by the wireless computers and devices in your
network. Please review the security types to determine which one you should use for
your network.
Wireless Encryption Types
WEP: Legacy encryption method supported by older 802.11b/g hardware. This is
the oldest and least secure type of wireless encryption. It is generally not
recommended to use this encryption standard, however if you have old 802.11 b or
802.11g wireless adapters or computers with old embedded wireless cards(wireless
clients), you may have to set your router to WEP to allow the old adapters to
connect to the router. Note: This encryption standard will limit connection speeds to
54Mbps.
WPA: This encryption is significantly more robust than the WEP technology. Much
of the older 802.11g hardware was been upgraded (with firmware/driver upgrades)
to support this encryption standard. Total wireless speeds under this encryption
type however are limited to 54Mbps.
WPA / WPA2: This setting provides the router with the ability to detect wireless
devices using either WPA or WPA2 encryption. Your wireless network will
automatically change the encryption setting based on the first wireless device
connected. For example, if the first wireless client that connects to your wireless
network uses WPA encryption your wireless network will use WPA encryption. Only
when all wireless clients disconnect to the network and a wireless client with WPA2
encryption connects your wireless network will then change to WPA2 encryption.
NOTE: WPA2 encryption supports 802.11n speeds and WPA encryption will limit
your connection speeds to 54Mbps
WPA2: This is the most secure wireless encryption available today, similar to WPA
encryption but more robust. This encryption standard also supports the highest
connection speeds. TRENDnet recommends setting your router to this encryption
standard. If you find that one of your wireless network devices does not support
WPA2 encryption, then set your router to either WPA or WPA-Auto encryption.
Note: Check the specifications of your wireless network adapters and wireless
appliances to verify the highest level of encryption supported.Below is brief
comparison chart of the wireless security types and the recommended
configuration depending on which type you choose for your wireless network.
Security Standard
WEP
WPA
WPA2
Compatible
Wireless
Standards
IEEE 802.11a/b/g/n
(802.11n devices
will operate at
802.11g speeds)
IEEE 802.11a/b/g/n
(802.11n devices
will operate at
802.11g speeds)
IEEE 802.11a/b/g/n
Highest
Performance
Under This
Setting
Up to 54Mbps
Up to 54Mbps
Up to 450Mbps*
Encryption
Strength
Low
Medium
High
Additional
Options
Open System or
Shared Key,
HEX or ASCII,
Different key sizes
TKIP or AES,
Preshared Key or
RADIUS
TKIP or AES,
Preshared Key or
RADIUS
Recommended
Configuration
Open System ASCII
13 characters
TKIP
Preshared Key
8-63 characters
AES
Preshared Key
8-63 characters
*Dependent on the maximum 802.11n data rate supported by the device (150Mbps,
300Mbps, or 450Mbps)

© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-816DRM
11
Secure your wireless network
Setup > Wireless Settings
After you have determined which security type to use for your wireless network (see
“How to choose the security type for your wireless network” on page 12), you can set up
wireless security.
1. Log into your router management page (see “Access your router management page”
on page 23).
2. Click on Setup, and click on Wireless Settings.
3. Click on the Security Mode drop-down list to select your wireless security type.
Selecting WEP:
WEP encryption is only available when 802.11b and 802.11g is selected in 802.11 Mode
section. Please note that 802.11n does not support WEP encryption. If selecting WEP
(Wired Equivalent Privacy), please review the WEP settings to configure and click Apply
to save the changes.
Authentication Type: Choose Open, Shared, or Auto.
Note: It is recommended to use Open System because it is known to be more secure
than Shared Key.
WEP Key 1-4
oChoose HEX or ASCII.
Note: It is recommended to use ASCII because of the much larger character set
that can be used to create the key.
oThis is where you enter the password or key needed for a computer to connect to
the router wirelessly
oYou can define up to 4 passwords or 4 keys. Only one key can be active at a given
time. Most users simply define one key.
oChoose a key index 1, 2, 3, or 4 and enter the key.
oWhen connecting to the router, the client must match both the password and the
Key number. (e.g. if you have activated Key 2 with a password of 12345, then the
client must select: Key 2 (entering Key 1, 3, or 4 will block the ability to connect)
and enter password 12345)
Selecting WPA-PSK, WPA-PSK / WPA2-PSK, or WPA2-PSK (WPA2-PSK recommended):
If selecting WPA-PSK, WPA-PSK / WPA2-PSK, or WPA2-PSK, (Wi-Fi Protected Access
Preshared Key) please review the settings to configure and click Apply to save the
changes.
WEP Key Format
HEX
ASCII
Character set
0-9 & A-F, a-f only
Alphanumeric (a,b,C,?,*, /,1,2, etc.)
64-bit key length
10 characters
5 characters
128-bit key length
26 characters
13 characters

© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-816DRM
12
First, from the Security Mode drop-down list, select WPA-PSK, WPA-PSK / WPA2-PSK,
or WPA2-PSK.
oSelect the Encryption type. When selecting WPA-PSK security, it is recommended
to use TKIP.
oWhen selecting WPA-PSK / WPA2-PSK security, it is recommended to use AES.
oWhen selecting WPA2-PSK security, it is recommended to use AES.
Create your Wireless security preshared key (password or key):
Preshare Key: Enter the preshared key.
oThis is the password or key that is used to connect your computer to this router
wirelessly
Note: 8-63 alphanumeric characters (a,b,C,?,*, /,1,2, etc.)
Then from the PSK/EAP row, select either PSK or EAP
PSK stands for Preshared Key
EAP stands for Extensive Authentication Protocol, also called Remote Authentication
Dial-In User Service or RADIUS).
Note: EAP requires an external RADIUS server, PSK only requires you to create a
passphrase.
Selecting WPA, WPA / WPA2, or WPA2:
If selecting WPA, WPA / WPA2, or WPA2 (Wi-Fi Protected Access Extensible
Authentication Protocol) please review the settings to configure and click Apply to save
the changes.
EAP (Extensible Authentication Protocol) is also called Remote Authentication Dial-In
User Service or RADIUS.
Select the Encryption Type
oWhen selecting WPA security, it is recommended to use TKIP.
oWhen selecting WPA / WPA2 security, it is recommended to use AES.
oWhen selecting WPA2 security, it is recommended to use AES.
oRADIUS Server IP:Enter the IP address of the RADIUS server. (e.g. 192.168.10.250)
oRADIUS Port: Enter the port your RADIUS server is configured to use for RADIUS
authentication.
Note: It is recommended to use port 1812.
oRADIUS Shared Key: Enter the shared key (or shared secret) used to authorize your
router with your RADIUS server.
Connect wireless devices to your router
A variety of wireless network devices can connect to your wireless network such as:
Gaming Consoles
Internet enabled TVs
Network media players
Smart Phones
Wireless Laptop computers
Wireless IP cameras

© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-816DRM
13
Each device may have its own software utility for searching and connecting to available
wireless networks, therefore, you must refer to the User’s Manual/Guide of your
wireless client device to determine how to search and connect to this router’s wireless
network.
See the “Appendix” on page 59 for general information on connecting to a wireless
network.
Connect wireless devices using WPS
Setup > Wireless Settings > WPS Setup
WPS (Wi-Fi Protected Setup) is a feature that makes it easy to connect devices to your
wireless network. If your wireless devices support WPS, you can use this feature to
easily add wireless devices to your network.
Note: You will not be able to use WPS if you set the SSID Broadcast setting to Disabled.
There are two methods the WPS feature can easily connect your wireless devices to
your network.
Push Button Configuration (PBC) method
oRECOMMENDED Hardware Push Button method–with an external button located
physically on your router and on your client device
oWPS Software/Virtual Push Button - located in router management page
PIN (Personal Identification Number) Method - located in router management page
Note: Refer to your wireless device documentation for details on the operation of
WPS.
Recommended Hardware Push Button (PBC) Method
Note: it is recommended that a wireless key (passphrase or password) is created
before connecting clients using the PBC method. If no wireless key is defined when
connecting via PBC, the router will automatically create an encryption key that is 64
characters long. This 64 character key will then have to be used if one has to
connect computers to the router using the traditional connection method.
To add a wireless device to your network, simply push the WPS button on the wireless
device you are connecting(consult client device User’s Guide for length of time), then
push and hold the WPS button located on your router for 3 seconds and release it. The
WLAN LED on your modem router will flash rapidly indicating that the WPS setup
process has been activated. (See “Product Hardware Features” on page 2)
For connecting additional WPS supported devices, repeat this process for each
additional device.
PBC (Software/Virtual Push Button)
Setup > Wireless Settings > WPS Setup
In addition to the hardware push button located physically on your router, the router
management page also has push button which is a software or virtual push button you
can click to activate WPS on your router.
1. Log into your router management page (see “Access your router management page”
on page 23).
2. Click on Setup and click Wireless Settings, then click on the WPS Setup button at the
bottom of the page.
3. To add a wireless device to your network, simply the push the WPS button on the
wireless device (consult wireless device’s User’s Guide for length of time), you are
connecting, then in your router management page, make sure the Config Method is
set to Push Button (default setting) and click on the Trigger button at the bottom of
the page.
4. The WPS Status area will display status messages about the WPS process.
5. The WPS Status area will display “Configured” message to indicate that the wireless
client device successfully connected using WPS.

© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-816DRM
14
PIN (Personal Identification Number)
Setup > Wireless Settings > WPS Setup
If your wireless device has WPS PIN (typically an 8-digit code printed on the wireless
device product label or located in the wireless device wireless software utility), you can
use this method.
1. Log into your router management page (see “Access your router management page”
on page 23).
2. Click on Advanced and click WPS Setting under the wireless band you would like to
configure (2.4GHz or 5GHz).
3. In the empty field next to Input Station PIN, enter the 8-digit WPS PIN of the wireless
client device you are connecting and click PIN.
Note: You may need to initiate the WPS PIN on your wireless device first when using
this method. Refer to your wireless device documentation for details on the
operation of WPS.
Basic wireless settings
Setup > Wireless Settings
This section outlines available management options under the Wireless Settings tab.
1. Log into your router management page (see “Access your router management page”
on page 23).
2. Click on Setup, and click on Wireless Settings.
3. To save changes to this section, click Apply when finished.
Enable Wireless
oEnable turns on the wireless networking on your router (by default it is enabled).
oDisable turns off wireless networking on your router.
Note: It is recommended to leave the wireless setting to Enable unless you do not
plan on connecting any wireless computers or devices to your network.
AP Isolate: Check this option to isolate the wireless bands to see each other. .
SSID: This acronym stands for Service Set Identifier and is the name of your wireless
network. It differentiates your wireless network from others around you. By default,
the router broadcast TRENDnet816 as the wireless network name. If you choose to
change the SSID, change it to a name that you can easily remember.
Visibility Status:
oVisible turns on broadcasting or your wireless network for clients to see.
oInvisible turns off broadcasting of wireless networking on your router.
Continent / Country: Select the country you the device is operating in.
Band Width: Select the appropriate mode for your network.
oB/G/N mixed: Select this mode for the best compatibility. This mode allows older
802.11b and 802.11g wireless devices to connect to the router in addition to newer
802.11n devices.
oB/G mixed: This mode only allows devices to connect to the router using older and
slow 802.11b or 802.11g technology and it thereby reduces the router’s maximum
speed to 54Mbps (typically not recommended).
oN only: This mode only allows newer 802.11n devices to connect to your router.
This mode does ensure the highest speed and security for your network, however if

© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-816DRM
15
you have older 802.11g wireless clients, they will no longer be able to connect to
this router.
oG only: This mode only allows devices to connect to the router using older and slow
802.11g technology (typically not recommended).
oB only: This mode only allows devices to connect to the router using older and slow
802.11b technology (typically not recommended).
Note: Please check the specifications on your wireless devices for the highest
wireless capability supported first before applying these settings. If you are unsure,
it is recommended that you keep the default setting (B/G/N mixed) for the best
compatibility.
When applying the 802.11 mode setting, please keep in mind the following:
oWireless devices that support 802.11n are backwards compatible and can connect
wirelessly at 802.11g or 802.11b.
oConnecting at 802.11b or 802.11g will limit the capability of your 802.11n
supported wireless devices from obtaining higher performance and data rates.
oAllowing 802.11b or 802.11g devices to connect to an 802.11n capable wireless
network may degrade the wireless network performance below the higher
performance and data rates of 802.11n.
oWireless devices that only support 802.11b or 802.11g will not be able to connect
to a wireless network that is set to 802.11n only mode.
oWireless devices that only support 802.11b will not be able to connect to a
wireless network that is set to 802.11g only mode.
Wireless Channel: In North America, this router can broadcast on 1 of 11 Channels (13
in Europe and other countries). Selecting the Auto option enables the router to
automatically select the best Channel for wireless communication. To manually set
the channel on which the router will broadcast, click the drop-down list and select the
desired Channel for wireless communication. The goal is to select the Channel that is
least used by neighboring wireless networks.
Guest Network
Setup > Wireless Settings
This section outlines available management options under the Wireless Settings tab.
1. Log into your router management page (see “Access your router management page”
on page 23).
2. Click on Setup, and click on Guest Network.
3. To save changes to this section, click Apply when finished.
Enable: Select to enable wireless guest network.
Guest (SSID): Enter the wireless name or SSID of your guest network.
Visibility Status:
oVisible turns on broadcasting or your wireless network for clients to see.
oInvisible turns off broadcasting of wireless networking on your router.
User Isolation: Select On to isolate all users connected to the guest network from
each other.
Disable WMM Advertise: Select this option to turn on or off WMM on the specified
network.
Max Clients: Enter the maximum wireless clients allowed to connect to the specified
network.

© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-816DRM
16
Steps to improve wireless connectivity
There are a number of factors that can impact the range of wireless devices. Follow
these tips to help improve your wireless connectivity:
1. Keep the number of obstructions to a minimum. Each obstruction can reduce the
range of a wireless device. Position the wireless devices in a manner that will
minimize the amount of obstructions between them.
a. For the widest coverage area, install your router near the center of your home,
and near the ceiling, if possible.
b.Avoid placing the router on or near metal objects (such as file cabinets and metal
furniture), reflective surfaces (such as glass or mirrors), and masonry walls.
c. Any obstruction can weaken the wireless signal (even non-metallic objects), so
the fewer obstructions between the router and the wireless device, the better.
d.Place the router in a location away from other electronics, motors, and
fluorescent lighting.
e. Many environmental variables can affect the router’s performance, so if your
wireless signal is weak, place the router in several locations and test the signal
strength to determine the ideal position.
2. Building materials can have a large impact on your wireless signal. In an indoor
environment, try to position the wireless devices so that the signal passes through
less dense material such as dry wall. Dense materials like metal, solid wood, glass
or even furniture may block or degrade the signal.
3. Antenna orientation can also have a large impact on your wireless signal. Use the
wireless adapter’s site survey tool to determine the best antenna orientation for
your wireless devices.
4. Interference from devices that produce RF (radio frequency) noise can also impact
your signal. Position your wireless devices away from anything that generates RF
noise, such as microwaves, radios and baby monitors.
If possible, upgrade wireless network interfaces (such as wireless cards in computers)
from older wireless standards to 802.11n. If a wirelessly networked device uses an older
standard, the performance of the entire wireless network may be slower. If you are still
experiencing low or no signal consider repositioning the wireless devices or installing
additional access points.
Advanced wireless settings
Setup > Wireless Settings
The advanced wireless features can provide you with additional options for setting up
your wireless network such as multiple SSID, activate/deactivate wireless according to
schedule, and operation modes such as WDS (Wireless Distribution System) bridging or
wireless bridging.
Multiple SSID
Setup > Wireless Settings
The multiple SSID feature allows you to broadcast up to two additional SSIDs (or
wireless network names). To wireless devices searching for available wireless networks
to connect to, the SSIDs (or wireless network names) will appear as separate and
different wireless networks. Since they appear as separate wireless networks, they are
also referred to as virtual APs (Access Points). Each virtual AP can be configured each
with a different SSID (or wireless network name), security type and additional settings
for wireless devices to connect. You can use the multiple SSID feature to setup guest
wireless accounts with a different security type to keep your primary wireless network
security information private. In addition, the SSIDs can be mapped to a specified VLAN
ID. See the VLAN section for instructions on assigning VLAN IDs to the SSIDs.
1. Log into your router management page (see “Access your router management page”
on page 23).
2. Click on Advanced, and click on MBSSID.
3. Review the settings and click Apply to save settings.
Enable: Check box to enable SSID
SSID (VAP): Enter the SSID you would like to apply.

© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-816DRM
17
BSSID: MAC address of the SSID
SSID Advertise: Select to broadcast SSID.
4. See section Secure your wireless network to configure wireless security settings.
Additional Wireless Settings
Advanced > Advanced Wireless
These settings are advanced options that can be configured to change advanced
wireless broadcast specifications. It is recommended that these settings remain set to
their default values unless you are knowledgeable about the effects of changing these
values. Changing these settings incorrectly can degrade performance.
1. Log into your router management page (see “Access your router management page”
on page 23).
2. Click on Advanced, and click on Advanced Wireless. Click Apply to save settings.
Transmit Power: The wireless transmit power can be modified to a lower setting
such as 50%, 25%, and 12% if necessary. Lowering the wireless transmit may help to
better stabilize the wireless connectivity and reduce the effects of wireless
interference in areas where there are several 2.4GHz wireless devices. (Default:
100%)
Beacon Interval: A beacon is a management frame used in wireless networks that
transmitted periodically to announce the presence and provide information about
the router’s wireless network. The interval is the amount time between each
beacon transmission.
Default Value: 100 milliseconds (range: 1-1000)
RTS Threshold: The Request To Send (RTS) function is part of the networking
protocol. A wireless device that needs to send data will send a RTS before sending
the data in question. The destination wireless device will send a response called
Clear to Send (CTS). The RTS Threshold defines the smallest data packet size
allowed to initiate the RTS/CTS function.
Default Value: 2346 (range: 256-2346)
Fragment Threshold: Fragmentation in wireless networks is the process of breaking
down data communications into smaller data packets in order to improve data
efficiency when transferring or receiving data between wireless devices. The
fragmentation threshold defines the maximum size of the data packets that are
broken down.
DTIM Interval: Is the interval of when the access point informs the clients about the
presence of buffered multicast/broadcast data.
Preamble Type: Select long or short preamble.
Wireless bridging using WDS (Wireless Distribution System)
Advanced > Wireless (2.4GHz or 5GHz) > WDS
Wireless bridging using WDS allows the device to create a wireless bridge with other
WDS supported wireless routers and access points configured in WDS mode to bridge
groups of network devices together wirelessly. Simultaneously, the router will also
function in access point mode allowing wireless client devices such as computers, game
consoles, mobile phones, etc. to connect in order to access network resources from
multiple groups of network devices as well as the Internet.
Note: You can create up to four WDS bridge connections on each wireless band (2.4GHz
and 5GHz). WDS (Wireless Distribution System) is not currently standardized and may
not connect to different model wireless routers or access points, therefore, when using
WDS, it is recommended to use the same model and version for wireless bridging.
By default, your router functions in Access Point mode to allow wireless client devices to
connect and access your network resources and access the Internet.
The diagram below shows your router in Access Point mode and clients connecting to
your router.