TRENDnet THA-103AC User manual

ŸHome Smart Switch (with Wireless Extender)
THA-103AC
ŸQuick Installation Guide (1)
THA-103AC (V1) /06.08.2015

1
1. Before You Start
ŸTHA-103AC
ŸQuick Installation Guide
ŸCD-ROM (User’s Guide)
Minimum Requirements
Package Contents
ŸExisting Wireless AC or N network
ŸMobile device (e.g. Smartphone, Tablet) with Android (version 2.3 or higher) or iOS
(version 6.1 or higher)

2
2. WPS Setup with iOS Device
1. For the initial installation, plug the THA-103AC into a power outlet near your router
or access point. Toggle the power switch down to the “On” position, and wait 30
seconds while the unit boots up.
2. Press and hold the WPS button on your router for 5 seconds.
0:05
WPS

3
4. Enable the WiFi settings on your iOS mobile device, and connect to your home
wireless network.
5. Go to the Apple App Store, and search for the TRENDnet Smart Home app, then
install the app. Or, scan the QR code below to download and install the app.
3. Press and hold the WPS button on the THA-103AC. To connect to a 2.4GHz
network, press and hold the button for three seconds and the WPS LED will flash.
To connect to a 5GHz network, press and hold the button for seven seconds, the
WiFi LED will flash. When the LED turns solid, the unit is connected.
2.4GHz
WPS
0:07 5GHz
0:03
6. Open the TRENDnet Smart Home app.

4
7. Tap the Add (+) icon
8. Click LAN Search.

5
9. Select the THA-103AC smart switch.
10. Enter the default password: admin.
11. Tap Done to save the changes.

6
12. Tap on the THA-103AC.
13. Tap the power icon to verify the outlet will turn on/off.
Blue ON Red OFF
14. Wireless extender’s setup is also finished. The THA-103AC can be moved to its
final location. To project the strongest signal from the built-in wireless extender, put
the unit in an area where your mobile device has at minimum three signal bars
from your wireless network.

7
15. Installation is now complete! For detailed configuration information and advanced
settings, Please refer to the User's Guide CD-ROM. Visit www.trendnet.com for
product updates and online support.
Note:
It is recommended that you change your password to ensure your device is secure. To
change the password, open the TRENDnet Smart Home app, and locate your device.
Click on the Device Settings icon, then select Advanced Settings. It is also
recommended that you change your wireless passwords. To do so, please login to the
device's configuration page and adjust your settings under the wireless section.

3. Manual Setup with iOS Mobile Device
8
1. To project the strongest signal from the built-in wireless extender, put the
THA-103AC in an area where your mobile device has at least three signal bars from
your wireless network. Toggle the power switch to the “On” position, and wait 30
seconds while the unit boots up.
2. Go to the Apple App store, and search for the TRENDnet Smart Home app, then
install the app. Or, scan the QR code below to download and install the app.
Note:
Ÿ Manual Setup uses TRENDnet's free app to connect the THA-103AC to your
wireless network.
Ÿ If you have an Android mobile device, skip to the next section, WPS Setup with
Android Device, or Section 5, Manual Setup with Android Device.

9
3. Enable the Wi-Fi settings on your iOS mobile device, and connect to the
THA-103AC.
4. Enter the wireless password and tap Join. The default password is password.
5. Open the TRENDnet Smart Home app.
6. Tap the Add (+) icon

10
7. Tap LAN Search.
8. Select the THA-103AC smart switch.

9. Enter the default device password: admin
10. Tap Done to save your changes.
11. Tap the Device Settings icon.

12
12. Tap Advanced Setting.
13. Tap WiFi Setting then tap WiFi.

13
14. Select your wireless network. The THA-103AC is capable of extending both
2.4GHz and 5GHz networks. If your router supports dual-band networking, you will
have to choose which network to connect with the unit.
16. Close the app.
18. Tap on the THA-103AC.
15. Enter your network's WiFi password and tap OK.
17. Connect your mobile device to your wireless network and re-launch the
TRENDnet Smart Home app.

14
19. Tap the power icon to verify if the outlet will turn on/off.
20. Installation and wireless extender's setup are now complete! For detailed
configuration information and advanced settings, please refer to the User's Guide
CD-ROM. Visit www.trendnet.com for product updates and online tech support.
Note:
It is recommended that you change your password to ensure your device is secure. To
change the password, open the TRENDnet Smart Home app, and locate your device.
Click on the Device Settings icon, then select Advanced Settings. It is also
recommended that you change your wireless passwords. To do so, please login to the
device's configuration page and adjust your settings under the wireless section.
Blue ON Red OFF

15
4. WPS Setup with Android Device
Note:
ŸWPS requires an external WPS button on your wireless router or access point in
order to connect the THA-103AC switch to your network. If your router does not
have a WPS button, or if you prefer to connect to your wireless network using our
free app, please skip to the next section, Manual Setup with Android Device
located below.
ŸIf you have an iOS mobile device, refer to Section 2, WPS Setup with iOS Mobile
Device, or Section 3, Manual Setup with iOS Mobile Device.
1. For the initial installation, plug in the THA-103AC into a power outlet near your
router or access point. Toggle the power switch down to the “On” position, and wait
30 seconds while the unit boots up.
2. Press and hold the WPS button on your router or access point for 5 seconds.
0:05
WPS

16
4. Enable the WiFi settings on your Android mobile device, and connect to your home
wireless network.
5. Go to the Google Play Store, search for the TRENDnet Smart Home app, and
install the app. Or, scan the QR code below to download and install the app.
3. Press and hold the WPS button on the THA-103AC. To connect to a 2.4GHz
network, press and hold the button for three seconds and the WPS LED will flash.
To connect to a 5GHz network, press and hold the button for seven seconds, the
WiFi LED will flash. When the LED turns solid, the unit is connected.
6. Open the TRENDnet Smart Home icon.
2.4GHz
WPS
0:07 5GHz
0:03

17
7. Tap the Add (+) icon.
8. Tap LAN Search.

18
9. Select the THA-103AC smart switch.
10. Enter the default password: admin.

19
11. Press the Add (+) icon.
12. Select the THA-103AC smart switch.