TRENDnet TE100-S800i User manual

2
1. Introduction
The 8 10/100Base-TX Management Switch is a compact switch that is ideal
for SOHO (Small Office or Home Office) networks. It provides wired-speeds,
Fast Ethernet switching, and store-and-forward switching to attain
high-performance at low-cost connections. It can also auto-learn and store
source addresses on an 8K-entry MAC address table.
The Switch provides 8 auto-sensing 10/100 Mbps RJ-45 Ethernet ports,
supporting Auto-MDIX function for each port. [In general, MDI means
connecting to another Hub or Switch while MDIX means connecting to a
workstation or PC. Therefore, Auto-MDIX means you can use any cable,
straight-through or cross-over, to connect to another Switch or workstation. ]
With its built-in Web-based Utility, managing and configuring the 8
10/100Base-TX Management Switch becomes easier. From cabinet
management to port-level control and monitoring, you can visually configure
and manage your network via Web Browser. Just click your mouse instead
of typing command strings. If you prefer using a Command Line Interface,
the 8 10/100Base-TX Management Switch can also be managed via Telnet,
Console, or SNMP Management.
Features
8 10/100BASE-TX intelligent switch
Switch fabric up to 3.8Gbps
Layer 2 Web-based management switch
IGMP support for Multi-media application
Port Mirroring supported
Spanning Tree, SNMP, RMON supported
Support Port-based VLAN

IEEE802 .1Q VLAN, GVRP supported
Support Class of Service
Broadcast Storm filter supported
Support Port Security
IEEE802.3ad Port trunk with LACP supported
Software Features
SNMP
RFC 1157 SNMP, RFC 1213 MIB II, Bridge MIB, RFC 1643
Ethernet Like, RFC 1493 Bridge MIB, RFC 1757 RMON1,
LANTECH Enterprise MIB, RFC 1215 Trap,
Management
Web management (IE)
RS-232 console management (Rear side)
Telnet
Trunk
IEEE 802.3ad Trunk with LACP for load distribution control
and fail over recovery
Up to 4 ports per group, max 4 Groups
Class of Service Global system supports 2 queues for Hi and Low priority
QoS Global System support 8 levels of priority and mapping to
Hi/Low priority queue for Class of Service
VLAN
Port based VLAN, 802.1Q Tag VLAN, Protocol Type VLAN,
GVRP support
VLAN ID up to 4094, VLANs up to 256 groups
IP Multicast
Support IGMP Snooping, supports 256 groups.
Support 2 types of Query mode for Enable/Disable or Auto
Query

4
Filter Database Support port static MAC address lock, MAC Filter, Port
Security
Port Mirror Use this feature to analyze port traffic. It supports a
maximum of 8 ports.
Broadcast
Control None, 5%, 10%, 15%, 20%, 25%
Spanning Tree IEEE802.1d support
RFC Standard
RFC 768 UDP, RFC 783 TFTP, RFC 791 IP, RFC792
ICMP, RFC 854 TELNET Server/Client, RFC 1112 IGMP,
RFC 2068 HTTP,
PackageContents
Unpack the contents of the 8 10/100Base-TX Management Switch and
verify them against the checklist below.
8 10/100Base-TX Management Switch
Power Cord
Four Rubber Feet
RS-232 cable
User Guide
8 10/100Base-TX Management Switch Power Cord

Rubber Feet RS-232 cable
Figure 1-2. Package Contents
Compare the contents of your 8 10/100Base-TX Management Switch
package with the checklist above. IF any item is missing or damaged,
please contact your local dealer for service.
ManagementMethods
The 8 10/100Base-TX Management Switch series supports the following
management methods:
Console and Telnet Management
Web-based Management
SNMP Network Management
Console and Telnet Management
Console Management is done through the RS-232 Console Port. Using this
method to manage the 8 10/100Base-TX Management Switch requires a
direct connection between the PC and the 8 10/100Base-TX Management
Switch. Telnet management is done over the network. Once the 8
10/100Base-TX Management Switch is on the network, you can use Telnet
to Log in and change the Switch’s configuration.
Web-based Management
The Switch provides an embedded HTML web site residing in flash memory.
It offers advanced management features that allow a user to manage the 8
10/100Base-TX Management Switch from anywhere on the network by
using a standard browser, such as Microsoft Internet Explorer.

6
SNMP Network Management
SNMP (Simple Network Management Protocol) provides a means to
monitor and control a network device, and to manage configuration, statistic
collection, performance, and security.

2. Hardware Description
This section mainly describes the hardware of the 8 10/100Base-TX
Management Switch.
FrontPanel
The Front Panel of the 8 10/100Base-TX Management Switch consist of 8
auto-sensing 10/100Mbps Ethernet RJ-45 ports (automatic MDI/MDIX).
The LED indicators are also located on the frond panel of the switch.
Figure 2-1. The Front Panel of the 8 10/100Base-TX Management Switch
RJ-45 Ports (Auto-MDIX): Eight 10/100Mbps ports can automatically
sense 10Base-T or 100Base-TX connections.
[In general, MDI means connecting to another Hub or Switch while
MDIX means connecting to a workstation or PC. Therefore, Auto-MDIX
means you can use any cable, straight-through or cross-over, to
connect to another Switch or workstation. ]
LEDIndicators
There are three LED-Indicators (100M, LNK/ACT, FDX/COL) for each UTP
port. The following table provides a description for each LED status and
meaning. They provide a real-time indication of systematic operation status.

8
Figure 2-2. LED Indicators
LED Status Color Description
Power On Green Power On
On Green
The port is operating at the
speed of 100Mbps.
100M
Off In 10Mbps mode or no
device attached
On Green
The port is successfully
connecting with the device.
Blinks Green The port is receiving or
transmitting data.
LNK /ACT
Off No device attached.
On Orange
The port is operating in
Full-duplex mode.
Blinks Orange
Collision of Packets occurs
in the port.
FDX /COL
Off Half-duplex mode or no
device attached.
Table 2-1. The description of LED Indicator
RearPanel
The Console port and 3-pronged power plug are located at the Rear Panel
of the 8 10/100Base-TX Management Switch as shown in Figure 2-3. The

Switch will work with the AC in the range of 100-240V AC, 50-60Hz.
Figure 2-3 The Rear Panel of the 8 10/100Base-TX Management Switch
Console Port: Console management can be done through the Console
Port. It requires a direct connection between the Switch and an end station
(PC) via a RS-232 cable.
DesktopInstallation
Set the switch on a sufficiently large flat space with a power outlet nearby.
The surface where you put your Switch should be clean, smooth, level, and
sturdy. Make sure there is enough clearance around the Switch to
allow attachment of cables, power cord and air circulation.
Attaching Rubber Feet
1. Make sure that the mounting surface on the bottom of the Switch is
grease and dust free.
2. Remove the adhesive backing from your Rubber Feet.
3. Apply the Rubber Feet to each corner on the bottom of the Switch.
These footpads help prevent shock/vibration.

10
Figure 2-4. Attaching Rubber Feet to each corner on the bottom of the Switch
Power On
Connect the power cord to the power socket on the rear panel of the Switch.
The other side of power cord connects to the power outlet. Check the power
indicator on the front panel to see if power is properly supplied.