TRENDnet TEW-740APBO User manual

TRENDnet User’s Guide
Cover Page

© Copyright 2016 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-740APBO
2
Contents
Product Overview ...........................................................................4
Package Contents .......................................................................................................... 4
Features......................................................................................................................... 4
Product Hardware Features........................................................................................... 5
Application Diagram ...................................................................................................... 7
Setup & Installation ........................................................................8
Note the Wireless MAC Addresses ................................................................................ 8
Setup Guide Assumed Defaults ........................................................................... 8
TEW-740APBO #1 Configuration ................................................................................... 9
TEW-740APBO #2 Configuration ................................................................................. 11
Verify Point-to-Point Configuration/Connectivity ....................................................... 12
Grounding Wire Installation ........................................................................................ 13
Waterproof Kit Installation .......................................................................................... 13
Mounting Hardware Installation ................................................................................. 16
Pole Mounting ................................................................................................... 16
Wall Mounting ................................................................................................... 17
Completed Point to Point Setup and Pole Mount Installation Example...................... 18
Installation Tips............................................................................................................ 19
Application Modes ........................................................................20
AP Mode (Access Point Mode) .................................................................................... 20
WDS Mode (Pure WDS) ............................................................................................... 21
Client Bridge + Universal Repeater Mode ................................................................... 22
CPE + AP Mode (Router Client + Access Point) ............................................................ 22
AP Mode Configuration.................................................................23
External Network Connection...................................................................................... 23
Network Requirement ....................................................................................... 23
Configure LAN IP.......................................................................................................... 23
Wireless LAN Network................................................................................................. 25
Wireless General Setup ..................................................................................... 25
Wireless Advanced Setup .................................................................................. 25
Wireless WMM QoS Setup ................................................................................ 27
Create Virtual AP (VAP) ..................................................................................... 29
Virtual AP Setup................................................................................................. 30
Wireless MAC Filter Setup ................................................................................. 32
Wireless Network Expansion ............................................................................. 32
System Status .............................................................................................................. 33
System Overview ............................................................................................... 33
Associated Clients Status ................................................................................... 34
Show WDS Link Status ....................................................................................... 34
Extra Information............................................................................................... 35
Event Log ........................................................................................................... 36
WDS Mode Configuration ............................................................. 37
External Network Connection ..................................................................................... 37
Network Requirement ....................................................................................... 37
Configure LAN IP.......................................................................................................... 37
Wireless Network Expansion....................................................................................... 38
Wireless General Setup ..................................................................................... 38
Wireless Advanced Setup .................................................................................. 39
Wireless WMM QoS Setup ................................................................................ 40
WDS Setup ......................................................................................................... 42
System Status .............................................................................................................. 42
System Overview ............................................................................................... 42
Extra Information............................................................................................... 43
Event Log ........................................................................................................... 44
WDS Link Status................................................................................................. 45
Repeater Mode............................................................................. 46
External Network Connection ..................................................................................... 46
Network Requirement ....................................................................................... 46

© Copyright 2016 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-740APBO
3
Configure LAN IP .......................................................................................................... 46
Wireless Network Expansion ....................................................................................... 47
Wireless General Setup ..................................................................................... 47
Wireless Advanced Setup .................................................................................. 48
Wireless WMM QoS Setup ................................................................................ 50
Site Survey ......................................................................................................... 51
Repeater AP Setup............................................................................................. 52
Wireless MAC Filter Setup ................................................................................. 54
Create Wireless Profile ...................................................................................... 54
Bandwidth Control............................................................................................. 56
Configure SNMP Setup ...................................................................................... 56
Configure Time Policy ........................................................................................ 57
System Status .............................................................................................................. 58
System Overview ............................................................................................... 58
DHCP Client........................................................................................................ 59
Extra Information............................................................................................... 59
Event Log ........................................................................................................... 60
Associated Client List ......................................................................................... 60
Remote AP status............................................................................................... 61
CPE + AP Mode Configuration........................................................61
External Network Connection...................................................................................... 61
Network Requirement ....................................................................................... 61
Configure CPE Setup .................................................................................................... 62
Configure DDNS Setup ....................................................................................... 63
Configure LAN IP ................................................................................................ 63
Configure Static IP address ................................................................................ 65
Access Point Association.............................................................................................. 65
Wireless General Setup ..................................................................................... 65
Wireless Advanced Setup .................................................................................. 66
Wireless WMM QoS Setup ................................................................................ 67
Site Survey ......................................................................................................... 69
Create Wireless Profile ...................................................................................... 69
AP Setup............................................................................................................. 71
Wireless AP MAC Filter Setup............................................................................ 73
Access Control ............................................................................................................. 74
DMZ ................................................................................................................... 74
IP Filter Setup .................................................................................................... 74
MAC Filter Setup................................................................................................ 75
Virtual Server..................................................................................................... 75
Bandwidth Control............................................................................................. 76
Routing .............................................................................................................. 76
Status........................................................................................................................... 76
System Overview ............................................................................................... 77
DHCP Client........................................................................................................ 77
Extra Information............................................................................................... 78
Event Log ........................................................................................................... 79
Associated Client List ......................................................................................... 79
Remote AP status .............................................................................................. 79
System Management .................................................................... 81
Configure Management..................................................................................... 81
Configure System Time...................................................................................... 82
Configure SNMP Setup ...................................................................................... 82
Enable UPNP ...................................................................................................... 83
Backup / Restore and Reset to Factory ............................................................. 83
Firmware Upgrade............................................................................................. 84
Network Utility .................................................................................................. 84
Reboot ............................................................................................................... 85
Technical Specifications ................................................................ 86
Appendix ...................................................................................... 88

© Copyright 2016 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-740APBO
4
Product Overview
TEW-740APBO
Package Contents
TEW-740APBO
CD-ROM (Software & User’s Guide)
Quick Installation Guide
Power adapter (48V DC, 0.5A)
Proprietary PoE injector
Waterproof RJ-45 kit
Grounding wire
Mounting hardware
Features
TRENDnet’s 10dBi Wireless N300 Outdoor PoE Access Point., model TEW-740APBO,
provides Wireless N300 building-to-building connectivity. A variety of installation
scenarios are facilitated with Access Point (AP), Wireless Distribution System (WDS),
Repeater, and CPE + AP modes. The IP67 rated housing comes with wall and pole
mounting hardware.
Multi-Mode Support
Supports Access Point (AP), Wireless Distribution System (WDS), Repeater, and Wireless
Client modes
Wireless N300 (2.4 GHz)
Compliant with 802.11n/g/b technology (2.4 GHz) with data rates up to 300 Mbps*
Outdoor Rated
Durable enclosure with an IP67 outdoor weather rating
Directional Antenna
Built in 10 dBi directional antenna
Power over Ethernet (PoE)
Comes with a proprietary PoE injector, so that it can connect a regular non-PoE switch
Logs
Real time logs and statistics help troubleshooting

© Copyright 2016 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-740APBO
5
Encrypted Wireless
Support for wireless encryption of up to WPA2
Multiple SSIDs
Create up to eight additional SSIDs
Compatibility
Compatible with legacy wireless devices
Mounting Hardware
Pole and wall mount hardware included
* Effective wireless coverage may vary depending on the wireless device's output
power, antenna gain, antenna alignment, receiving sensitivity, and radio interference.
Additionally environmental factors such as weather conditions, physical obstacles, and
other considerations may affect performance. For optimal results, we recommended
consulting a professional installer for site survey, safety precautions, and proper
installation.
Product Hardware Features
Front View
IP67 Weather
Rated Housing
with built-in
directional sector
antenna

© Copyright 2016 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-740APBO
6
Bottom View
Reboot/Reset Button –You will need to unscrew the protective cover or
disconnect the RJ-45 waterproof kit if it is installed to gain access to this
button. Press and hold this button for 2 seconds and release to reboot the
device. Press and hold this button for 10 seconds and release to reset the
device to factory defaults.
Power LED –The indicator will turn when the device is powered on.
WLAN Connection Quality Indicators –The connection quality indicators will
turn on depending on the connection quality during installation. These
indicators can help to assist with optimal placement and positioning during
mounting/hardware installation.
Good Connection Quality
Better Connection Quality
Best Connection Quality
LAN Port –You will need to unscrew the protective cover to gain access to this
port. The Ethernet LAN port operates at 10/100Mbps and is also used to supply
power to the device using only the included proprietary PoE injector.
Proprietary PoE Injector –
oPOWER IN –Connect the included power adapter connector to this
input and adapter side into an AC power source to supply power to
the injector.
oP+DATA OUT –Connect an Ethernet RJ-45 cable to this output and the
other side to the device LAN port to supply power to the device.
o10/100 DATA IN –Connect an Ethernet RJ-45 cable to this input and
connect the other to your network or directly to computer for initial
device setup.

© Copyright 2016 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-740APBO
7
Ground Screw Fitting –The ground screw is built into the device housing. The
fitting can be identified on the back of the housing by checking for the ground
symbol. The included ground screw and wire can be used to attached the
device to a known grounding point. (ex. Earth driven rod, grounded electrical
system, building frame, etc.)
Application Diagram
The example application displays two TEW-740APBO access points are configured in WDS point-
to-point bridge mode and establishing a wireless link between each and other, allowing for
network connectivity between two buildings over a point-to-point wireless link.

© Copyright 2016 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-740APBO
8
Setup & Installation
The intended purpose and application for this product is to extend network connectivity
across long physical distances outside of an area or building that lacks local connectivity
using point to point wireless bridge capability using 802.11 standards.
Although this product supports multiple wireless modes, the basic installation will only
cover the primary application of point to point wireless connectivity.
Minimum Requirements
Computer with RJ-45 Ethernet port and web browser
2 x RJ-45 Ethernet cables (not included)
Phillips screwdriver (not included)
Important Note:
The access point does not support standard IEEE 802.3at/af PoE/PoE+. Only the included
proprietary PoE injector may be used to supply power to the access point. For safety,
use only the included PoE injector to supply power to the access point.
It is strongly recommended that you configure the access points first before mounting
them in their desired locations.
Access Point Default Settings
LAN IP Address: 192.168.10.100
LAN Subnet Mask: 255.255.255.0
User: admin
Password: admin
The following steps assume you are setting up and installation two TRENDnet TEW-
740APBO access points in point to point configuration.
Note the Wireless MAC Addresses
Please check the device label on both access points and write down or note the item
labeled MAC1 from both access points. MAC1 is the wireless MAC address assigned to
each access point and will be used later in the configuration steps.
Setup Guide Assumed Defaults
In this guide, we will assume the following defaults and settings:
TEW-740APBO #1 MAC1: 00:11:22:33:44:55
TEW-740ABPO #2 MAC1: AA:BB:CC:DD:EE:FF
Network Router/Gateway IP Address/Netmask: 192.168.10.1 / 255.255.255.0
Network Router/Gateway DHCP IP Pool: 192.168.10.101-192.168.10.199
Note: Please note that if your existing network router/gateway IP address/subnet
settings are different than the network settings assumed above, you will need to modify
the assigned IP configuration to each access point accordingly to within you specific
subnet.
Before mounting the access points in their desired locations, please configure access
points first.

© Copyright 2016 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-740APBO
9
TEW-740APBO #1 Configuration
1. Connect the power adapter connector side to the POWER IN on the included
proprietary PoE injector and the adapter to an AC power source.
Note: EU model also include an on/off power switch. Please make sure to switch to the
(On/-) position.
2. Connect an RJ-45 Ethernet cable from the access point LAN port to the P+DATA OUT
on the included proprietary PoE injector.
3. Connect an RJ-45 Ethernet cable from the computer to the 10/100 DATA IN on the
included proprietary PoE injector.
4. The access point power LED will turn on to indicate the device is receiving power.
5. Assign a static IP address to your computer network adapter in the subnet of
192.168.10.x (ex. 192.168.10.10) and subnet mask of 255.255.255.0.
6. Open your web browser and type in the IP address of the access point in the address
bar, then press Enter. The default IP address of the access point is 192.168.10.100.
7. When prompted to login, enter the default user name and password and click OK.
Default User Name: admin
Default Password: admin

© Copyright 2016 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-740APBO
10
8. At the Password Setup page, enter your new password in the New admin Password
field and once again in the Check admin Password field to confirm, then click Save to
apply the new password settings.
Note: It is recommended to change to a strong admin password. This is the password
that will be used to login to the access point management configuration web page.
9. In the access point management web page, click on System and click on LAN.
10. Under Static IP, enter the IP address settings below, then scroll down and click Save
to apply the settings. After changes are applied, you will need to login to the new IP
address assigned.
Note: Please note that if your existing network IP subnet is different. You must assign IP
addresses available in your IP subnet to the access points accordingly.
TEW-740ABO #1 IP Configuration
IP Address: 192.168.10.50
IP Netmask: 255.255.255.0
IP Gateway: 192.168.10.1
11. Click System and click on Operating Mode. In the list, select WDS and click on Save
& Reboot to apply the settings.
12. Click on Wireless and click on General.
You can choose to change the Channel settings but they must match on both access
points to establish a point-to-point WDS configuration. For this example, we will leave
as the default channel 6. If you decide to change it, make sure to scroll down and click
Save to apply the setting.
13. Click on Wireless and click on Virtual AP. For VAP0, click on Edit.
14. You can choose to change the ESSID (Wireless Network Name) settings but they
must match on both access points to establish a point-to-point WDS configuration. For
this example, we will leave as the default setting TRENDnet7400_2.4GHz.

© Copyright 2016 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-740APBO
11
15. Under WDS Setup, set the Service setting to Enable.
16. In the first field for item 1, check the Enable option and in the WDS Peer’s MAC
Address fields, enter the MAC address of the 2nd TEW-740ABPO (TEW-740APBO #2
MAC1: AA:BB:CC:DD:EE:FF) noted earlier in this guide. Description field is optional.
Note: You will need to enter the wireless MAC address of your 2nd access point as the one
below is only used as an example in this guide.
17. In the Security Type field above, it is recommended to select AES and assign a
passphrase. It is not required to create a point-to-point WDS link but strongly
recommended. This setting must match on both access points.
If you decide to apply encryption and assign a passphrase, select AES. Then scroll down
to the bottom under the AES section and enter Passphrase. The security type and key
must match on both access points. Then click Save to save the settings.
Note: It is strongly recommended to assign strong passphrase. We are only using the
encryption key 1234567890 as an example in this guide.
18. At the top of the page, click Reboot,then click the Reboot button on the GUI page
to commit all of the changes. This completes the configuration for TEW-740APBO #1.
TEW-740APBO #2 Configuration
1. Repeat the same TEW-740APBO #1 configuration steps 1-9 for TEW-740ABPO #2.
2. On the TEW-740APBO #1 configuration step 10, use the IP configuration settings
below for TEW-740APBO #2.
Note: Please note that if your existing network IP subnet is different. You must assign IP
addresses available in your IP subnet to the access points accordingly.
TEW-740ABO #2 IP Configuration
IP Address: 192.168.10.51
IP Netmask: 255.255.255.0
IP Gateway: 192.168.10.1
3. Repeat the same TEW-740APBO #1 configuration steps 11-15 for TEW-740ABPO #2.
4. On the TEW-740APBO #1 configuration step 16, enter the MAC address of the 1st
TEW-740ABPO (TEW-740APBO #1 MAC1: 00:11:22:33:44:55) noted earlier in this guide.
Description field is optional.
Note: You will need to enter the wireless MAC address of your 1st access point as the one
below is only used as an example in this guide.
5. Repeat the same TEW-740APBO #1 configuration steps 11-18 to complete the TEW-
740ABPO #2 configuration. This completes the configuration for TEW-740APBO #2

© Copyright 2016 TRENDnet. All Rights Reserved.
12
TRENDnet User’s Guide
TEW-740APBO
Verify Point-to-Point Configuration/Connectivity
1. Make sure both access points (TEW-740APBO #1 and TEW-740APBO #2) powered on and positioned pointing toward each other.
2. With the static IP address still assigned from the setup guide, connect your computer to one of the access points via LAN port.
3. On your computer, open a command prompt/terminal window and run a ping command to test connectivity to both access point IP addresses 192.168.10.50 and 192.168.10.51.
Example of successful ping replies below from both access points. You can also check if you can access both access point web management pages through a web browser.
C:\Users\trendnet>ping 192.168.10.50
Pinging 192.168.10.50 with 32 bytes of data:
Reply from 192.168.10.50: bytes=32 time<1ms TTL=128
Reply from 192.168.10.50: bytes=32 time<1ms TTL=128
C:\Users\trendnet>ping 192.168.10.51
Pinging 192.168.10.51 with 32 bytes of data:
Reply from 192.168.10.51: bytes=32 time<1ms TTL=128
Reply from 192.168.10.51: bytes=32 time<1ms TTL=128

© Copyright 2016 TRENDnet. All Rights Reserved.
13
TRENDnet User’s Guide
TEW-740APBO
Grounding Wire Installation
To install the grounding wire, align one end of the ground wire over the ground fitting,
then secure the wire using the included screw and washer as shown below.
Waterproof Kit Installation
1. Unscrew the sealing nut from the main body.
2. Separate rubber seal from the claw.
3. Verify that you have the following parts as shown below:
Cable Gland
Seal
Claw
Sealing Nut
4. Insert one end of an Ethernet cable into the sealing nut.

© Copyright 2016 TRENDnet. All Rights Reserved.
14
TRENDnet User’s Guide
TEW-740APBO
5. Insert the Ethernet cable into the seal.
6. Insert the seal into the claw.
7. Insert the seal/rubber claw into the cable gland.
8. Connect the Ethernet cable to the LAN port on the bottom of the access point.

© Copyright 2016 TRENDnet. All Rights Reserved.
15
TRENDnet User’s Guide
TEW-740APBO
9. Fasten and tighten the plug to the housing of the access point.
10. Fasten and tighten the cap to the weather proof plug.

© Copyright 2016 TRENDnet. All Rights Reserved.
16
TRENDnet User’s Guide
TEW-740APBO
Mounting Hardware Installation
Pole Mounting
Note: The pole mounting clamp supports poles with a maximum diameter of 101 mm (3.98 in.)
1. Align the mounting bracket with the hole on the unit and secure it with the M6x8 screw and washer provided.
2. Slide the two provided pole mounting clamps around the pole. Place the mounting bracket at the desired height and position.
3. Secure the TEW-740APBO to the pole mounting bracket using mounting clamp screws.
4. Adjust the orientation of the access point as necessary.

© Copyright 2016 TRENDnet. All Rights Reserved.
17
TRENDnet User’s Guide
TEW-740APBO
Wall Mounting
1. Align the mounting bracket with the hole on the unit and secure it with the M6x8 screw and washer provided.
2. Position the provided mounting bracket to the desired location and wall mount with screws or fasteners using the four mounting bracket holes.

© Copyright 2016 TRENDnet. All Rights Reserved.
18
TRENDnet User’s Guide
TEW-740APBO
Completed Point to Point Setup and Pole Mount Installation Example

© Copyright 2016 TRENDnet. All Rights Reserved.
19
TRENDnet User’s Guide
TEW-740APBO
Installation Tips
There are a number of factors that can impact the range of wireless devices.
1. Adjust your wireless devices so that the signal is traveling in a straight path, rather than at an angle. The more material the signal has to pass through the more signal you will lose.
2. Keep the number of obstructions to a minimum. Each obstruction can reduce the range of a wireless device. Position the wireless devices in a manner that will minimize the amount
of obstructions between them.
3. Building materials can have a large impact on your wireless signal. In an indoor environment, try to position the wireless devices so that the signal passes through less dense material
such as dry wall. Dense materials like metal, solid wood, glass or even furniture may block or degrade the signal.
4. Antenna orientation can also have a large impact on your wireless signal. Use the wireless adapter’s site survey tool to determine the best antenna orientation for your wireless
devices.
5. Interference from devices that produce RF (radio frequency) noise can also impact your signal. Position your wireless devices away from anything that generates RF noise, such as
microwaves, radios and baby monitors.
If you are still experiencing low or no signal consider repositioning the wireless devices or installing additional access points. The use of higher gain antennas may also provide the
necessary coverage depending on the environment. Please note to use the wireless connection quality indicators during installation to determine the optimal positioning when mounting
your access points.

© Copyright 2016 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-740APBO
20
Application Modes
Although the access point is intended to be used for WDS point-to-point bridging, the access point offers other operating modes. The access point multiple mode system which can be
configured either as a wireless gateway or an access point as desired. It also can be used as a WDS (Wireless Distribution System) link for Ethernet network expansion. This section
depicts different applications on Router AP Mode, AP Mode, WDS Mode, CPE Mode, Client Bridge + Universal Repeater Mode and CPE + AP Mode.
The different modes can be found under System > Operating Mode in the access point web management page.
AP Mode (Access Point Mode)
An access point can be either a main, relay or remote base station. A main base station is typically connected to a wired network via the Ethernet port. A relay base station relays data
between main base stations and relay stations or remote base stations with clients. A remote base station is the end point to accept connections from wireless clients and pass data
upstream to a network wirelessly.
Example 1: Access Point Only
It can be deployed as a traditional fixed wireless access point.
Example 2: Access Point + WDS Bridging
It can be deployed as a traditional fixed wireless access point and establish WDS bridging to an upstream access point to expand a network.
Main
WDS
Remote
Main
WDS
Remote