TRENDnet TEW-755AP User manual

TRENDnet User’s Guide
Cover Page

© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
Table of contents
2
Table of Contents
Table of Contents............................................................................2
Product Overview ...........................................................................4
Package Contents .......................................................................................................... 4
Features......................................................................................................................... 4
Product Hardware Features........................................................................................... 5
Application Diagram ...................................................................................................... 6
Connect wireless devices to your access point.............................................................. 7
Getting Started ...............................................................................7
Steps to improve wireless connectivity ......................................................................... 8
Connect wireless devices to your access point.............................................................. 9
Configuration..................................................................................9
Wireless Networking and Security .................................................11
How to choose the type of security for your wireless network .................................. 11
Secure your wireless network ..................................................................................... 13
Connect wireless devices using WPS ........................................................................... 15
Advance configuration ..................................................................16
Access the management page..................................................................................... 16
Operating Modes......................................................................................................... 17
Access Point..................................................................................18
Basic............................................................................................................................. 18
Wireless Profile............................................................................................................ 19
Wireless MAC filter...................................................................................................... 19
Client Bridge .................................................................................20
Basic............................................................................................................................. 20
Scan for wireless networks .......................................................................................... 20
WDS .............................................................................................21
WDS Link...................................................................................................................... 22
Basic............................................................................................................................. 22
Wireless Profile............................................................................................................ 23
Repeater....................................................................................... 24
Basic............................................................................................................................. 24
Scan for wireless networks.......................................................................................... 24
Advanced wireless settings ......................................................................................... 25
Advanced Wireless ............................................................................................ 25
HT Physical Mode .............................................................................................. 25
Client Limit......................................................................................................... 26
Band Steering .............................................................................................................. 26
Change your IP address ............................................................................................... 26
Create schedules ......................................................................................................... 26
Configure Spanning Tree ............................................................................................. 27
Set date and time ........................................................................................................ 27
Manage VLAN .............................................................................................................. 28
Traffic Shaping ............................................................................................................. 28
Enable SNMP ............................................................................................................... 28
Enable CLI .................................................................................................................... 29
LED Controls ................................................................................................................ 29
Maintenance & Monitoring........................................................... 30
Reset to factory defaults ............................................................................................. 30
Backup and restore your configuration settings ......................................................... 30
Restart access point..................................................................................................... 30
Upgrade your firmware ............................................................................................... 31
Configure log ............................................................................................................... 32
Test connectivity.......................................................................................................... 32

© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
Table of contents
3
Check system information ........................................................................................... 32
Check connected wireless clients ................................................................................ 33
Status > IPv6 Status ..................................................................................................... 33
Software Controller utility.............................................................34
Installation ................................................................................................................... 34
Add and Delete Device ................................................................................................ 34
Device Settings ............................................................................................................ 35
Upgrade Firmware....................................................................................................... 35
Load configuration....................................................................................................... 36
Troubleshooting............................................................................37
Appendix ......................................................................................38

© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-755AP
4
Product Overview
TEW-755AP
Package Contents
In addition to your router, the package includes:
TEW-755AP
5 ft. (1.5 m) network cable
CD-ROM (Utility and User’s Guide)
Quick Installation Guide
Power adapter (12V DC, 1A)
Mounting bracket
If any package contents are missing or damaged, please contact the retail store, online
retailer, or reseller/distributor from which the product was purchased.
Features
TRENDnet’s high performance N300 PoE Access Point, model TEW-755AP,
supports Access Point (AP), Client, Wireless Distribution System (WDS) AP, WDS
Bridge, WDS Station, and Repeater modes. It generates a 300 Mbps WiFi N
network and features a Gigabit PoE port. The included Windows-based software
controller manages multiple TEW-755APs and reduces WiFi
management/troubleshooting time. A low profile housing blends into most
environments and a mounting plate eases installation.
Multi-Language
Multi-Language Interface: English, Spanish, French, German, and Russian
Power over Ethernet (PoE)
Saves remote location installation time and costs with Gigabit PoE
support (Optional power port for non-PoE installations)
WiFi N300
Low profile access point delivers proven WiFi N300
Multi-Mode Support
Supports Access Point (AP), Client, WDS AP, WDS Bridge, WDS Station,
and Repeater modes
Software Controller
The included Windows-based Software Controller manages multiple
TEW-755APs and reduces WiFi configuration, management, and
troubleshooting time
Gigabit Port
Gigabit PoE LAN port maintains high performance connections to the
wired network
Wireless Coverage
Extended wireless coverage with MIMO antenna technology

© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-755AP
5
2.4GHz
LAN
PWR
Encrypted Wireless
Support for wireless encryption of up to WPA2
WiFi Traffic Shaping
Manage traffic allocation per VLAN
IPv6
IPv6 network support
Low Profile
Off white low profile housing blends into most environments
LED Control
Further reduce product visibility by turning off LED indicators
Mounting Plate
Mounting plate reduces installation time
*Maximum wireless signal rates are referenced from IEEE 802.11 theoretical
specifications. Actual data throughput and coverage will vary depending on
interference, network traffic, building materials and other conditions.
Product Hardware Features
Top View
2.4GHz: This LED indicator turns green when the wireless is enabled. The LED
indicator blinks during data transmission
LAN: This LED indicator turns green when the access point LAN port is connected.
The LED indicator blinks during data transmission
PWR: This indicator turns green when the device is powered.
Off white low profile housing

© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-755AP
6
Reset
button
Front View
Gigabit port: Plug an Ethernet cable (also called network cables) from
your access point to your router and wired network devices.
Power port: Connect the power adapter from your access point power port to
an available power outlet.
Reset button: Use a sharp tool to press and hold this button for 10 seconds to
reset the access point.
Application Diagram
The access point provides 300 Mbps WiFi N combined with AP, Client, WDS and Repeater modes
support multiple applications.
Gigabit Port
Power port

© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-755AP
7
Connect wireless devices to your access point
A variety of wireless network devices can connect to your wireless network such as:
Wireless Laptop computers
Network media players
Wireless IP cameras
Smart Phones
Gaming Consoles
Internet enabled TVs
Each device may have its own software utility for searching and connecting to available
wireless networks, therefore, you must refer to the User’s Manual/Guide of your
wireless client device to determine how to search and connect to this router’s wireless
network.
See the “Appendix” on page 53 for general information on connecting to a wireless
network.
Getting Started
For a typical wireless setup at home or office when using the access point in AP mode,
please do the following:
Installation
1. Connect the power adapter to the power port of the access point. Or simply plug an
Ethernet cable on the access point to a PoE (Power over Ethernet) switch that
connects to your router or network.
2. If using the power adapter, plug an Ethernet cable to the access point and plug the
other end to your router or network.
3. Verify that all LEDs are on.
4. For your security, each TEW-755AP comes pre-encrypted with a unique WiFi Name
(SSID) and WiFi Password. You can find your device's SSID and WiFi password on the
white labels located on the device. Use this information to connect to the TEW-755AP
access point.
5. Verify your connection to you network by accessing the Internet. For advanced
configuration continue to the advanced sections of the user manual.
Mounting device
1. Remove the mount plate from the access point.
2. Place the mounting plate on the wall or ceiling where the device will be located and
mark the location of the screw holes. Ensure that the device has enough clearance to
slide on and off the mounting plate.
3. Drill out the marked holes and insert the plastic wall anchors in to the wall.

© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-755AP
8
4. Secure the mounting plate using the screws that came with the device.
5. Place the access point on the mounting plate and slide to lock into position.
Steps to improve wireless connectivity
There are a number of factors that can impact the range of wireless devices. Follow
these tips to help improve your wireless connectivity:
1. Keep the number of obstructions to a minimum. Each obstruction can reduce the
range of a wireless device. Position the wireless devices in a manner that will
minimize the amount of obstructions between them.
a. For the widest coverage area, install your router near the center of your home, and
near the ceiling, if possible.
b.Avoid placing the router on or near metal objects (such as file cabinets and metal
furniture), reflective surfaces (such as glass or mirrors), and masonry walls.
c. Any obstruction can weaken the wireless signal (even non-metallic objects), so the
fewer obstructions between the router and the wireless device, the better.
d.Place the router in a location away from other electronics, motors, and fluorescent
lighting.
e. Many environmental variables can affect the router’s performance, so if your
wireless signal is weak, place the router in several locations and test the signal
strength to determine the ideal position.
2. Building materials can have a large impact on your wireless signal. In an indoor
environment, try to position the wireless devices so that the signal passes through
less dense material such as dry wall. Dense materials like metal, solid wood, glass or
even furniture may block or degrade the signal.
3. Antenna orientation can also have a large impact on your wireless signal. Use the
wireless adapter’s site survey tool to determine the best antenna orientation for your
wireless devices.
4. Interference from devices that produce RF (radio frequency) noise can also impact
your signal. Position your wireless devices away from anything that generates RF
noise, such as microwaves, radios and baby monitors.
If possible, upgrade wireless network interfaces (such as wireless cards in computers)
from older wireless standards to 802.11n. If a wirelessly networked device uses an older
standard, the performance of the entire wireless network may be slower. If you are still
experiencing low or no signal consider repositioning the wireless devices or installing
additional access points.

© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-755AP
9
Connect wireless devices to your access point
A variety of wireless network devices can connect to your wireless network such as:
Gaming Consoles
Internet enabled TVs
Network media players
Smart Phones
Wireless Laptop computers
Wireless IP cameras
Each device may have its own software utility for searching and connecting to available
wireless networks, therefore, you must refer to the User’s Manual/Guide of your
wireless client device to determine how to search and connect to this router’s wireless
network.
See the “Appendix” on page 63 for general information on connecting to a wireless
network.
Configuration
Note: The access point’s default management page http://192.168.10.100 is accessed
through the use of your Internet web browser (e.g. Internet Explorer, Firefox, Chrome,
Safari, and Opera) and will be referenced frequently in this User’s Guide.
Before accessing the web-based management page, configure the IP address and
subnet mask of your computer to the following:
IP Address: 192.168.10.xxx
Subnet Mask: 255.255.255.0
1. Open your web browser (e.g. Internet Explorer, Firefox, Safari, Chrome, or Opera) and
go to http://tew-755ap or type in http://192.168.10.100.
2. Enter the default user name and password and then click Login. You can find your
device's SSID and WiFi password on the white labels located on the device. Use this
information to connect to the TEW-755AP access point.

© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-755AP
10
Wizard
1. For the first time logging into the device the setup wizard will start automatically.
2. Your security the first step is to change the login password of the access point. Enter
your new login password and click OK.
3. Your new password settings will be applied and you will be redirected to the login
screen. You will need to use the new login password to proceed.
Using the utility
For additional information on the utility please go to software controller section.
1. Insert the CD ROM included with the access point.
2. Click on Software controller to install the utility.
3. Once the utility is installed click on Discover to refresh the list of access points.
4. Select the access point you want to configure.

© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-755AP
11
5. Click on Device settings to configure the access point.
Product Name: Displays the device model
IP Mode: Select the IP mode to apply on the device
oDHCP: Select this option to allow the device to receive IP address from your
DHCP server
oStatic: Select this option to manually set the IP address of the device
IP Address: Enter the IP address to assign to the device
Subnet Mask: Enter the subnet mask to assign to the device
Gateway: Enter the gateway IP address to assign to the device
System Name: Assign name of the device to help distinguish between similar
devices
Band: Select on the pull down menu the wireless interface to configure
Enable: Select this option to enable the selected wireless interface
Visible: Select this option to wireless broadcast the selected wireless interface
SSID: Enter the SSID (Wireless Network Name) of the selected wireless interface
Security: Select the wireless encryption security for to assign the selected
wireless interface
Key: Enter the wireless encryption security key or password
Channel: Select the wireless channel of the selected wireless interface
802.11 Mode: Select the 802.11 mode of the selected wireless interface
Password: Enter the login password of the device and click OK to save settings.
Wireless Networking and Security
How to choose the type of security for your wireless network
Setting up wireless security is very important. Leaving your wireless network open and
unsecure could expose your entire network and personal files to outsiders. TRENDnet
recommends reading through this entire section and setting up wireless security on your
new router.
There are a few different wireless security types supported in wireless networking each
having its own characteristics which may be more suitable for your wireless network
taking into consideration compatibility, performance, as well as the security strength
along with using older wireless networking hardware (also called legacy hardware).
It is strongly recommended to enable wireless security to prevent unwanted users from
accessing your network and network resources (personal documents, media, etc.).
In general, it is recommended that you choose the security type with the highest
strength and performance supported by the wireless computers and devices in your
network. Please review the security types to determine which one you should use for
your network.

© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-755AP
12
Wireless Encryption Types
WEP: Legacy encryption method supported by older 802.11b/g hardware. This is
the oldest and least secure type of wireless encryption. It is generally not
recommended to use this encryption standard, however if you have old 802.11 b or
802.11g wireless adapters or computers with old embedded wireless cards(wireless
clients), you may have to set your router to WEP to allow the old adapters to
connect to the router.
Note: This encryption standard will limit connection speeds to 54Mbps.
WPA: This encryption is significantly more robust than the WEP technology. Much
of the older 802.11g hardware was been upgraded (with firmware/driver upgrades)
to support this encryption standard. Total wireless speeds under this encryption
type however are limited to 54Mbps.
WPA-Auto: This setting provides the router with the ability to detect wireless
devices using either WPA or WPA2 encryption. Your wireless network will
automatically change the encryption setting based on the first wireless device
connected. For example, if the first wireless client that connects to your wireless
network uses WPA encryption your wireless network will use WPA encryption. Only
when all wireless clients disconnect to the network and a wireless client with WPA2
encryption connects your wireless network will then change to WPA2 encryption.
Note: WPA2 encryption supports 802.11n speeds and WPA encryption will limit
your connection speeds to 54Mbps
WPA2: This is the most secure wireless encryption available today, similar to WPA
encryption but more robust. This encryption standard also supports the highest
connection speeds. TRENDnet recommends setting your router to this encryption
standard. If you find that one of your wireless network devices does not support
WPA2 encryption, then set your router to either WPA or WPA-Auto encryption.
Note: Check the specifications of your wireless network adapters and wireless
appliances to verify the highest level of encryption supported. Below is brief
comparison chart of the wireless security types and the recommended
configuration depending on which type you choose for your wireless network.
Security Standard
WEP
WPA
WPA2
Compatible
Wireless
Standards
IEEE 802.11a/b/g
(802.11n devices
will operate at
802.11g to connect
using this standard)
IEEE 802.11a/b/g
(802.11n devices
will operate at
802.11g to connect
using this
IEEE 802.11a/b/g/n
standard)
Highest
Performance
Under This
Setting
Up to 54Mbps
Up to 54Mbps
Up to 450Mbps (11n)
and up to 1.3Gbps
(11ac)*
Encryption
Strength
Low
Medium
High
Additional
Options
Open System or
Shared Key,
HEX or ASCII,
Different key sizes
TKIP or AES,
Preshared Key or
RADIUS
TKIP or AES,
Preshared Key or
RADIUS
Recommended
Configuration
Open System ASCII
13 characters
TKIP
Preshared Key
8-63 characters
AES
Preshared Key
8-63 characters
*Dependent on the maximum data rate supported by the device (150Mbps, 300Mbps,)

© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-755AP
13
Secure your wireless network
Wireless Security
After you have determined which security type to use for your wireless network (see
“How to choose the security type for your wireless network” on page 12), you can set up
wireless security.
1. Log into your router management page (see “Access the management page” on page
16).
2. Click on the Wireless 2.4GHz
3. Underneath the basic wireless band section, you will see Wireless Network and all
your wireless network profiles will be listed.
4. Click on the Edit button next to the wireless profile you want to configure.
5. Select from the drop-down list to the wireless security to configure.
Selecting WEP-OPEN, WEP-SHARED: If selecting WEP (Wired Equivalent Privacy), please
review the WEP settings to configure and click Apply to save the changes.
Note: WPS functionality is not available when using WEP.
In the Security Mode drop-down list, select WEP-OPEN or WEP-SHARED.
Note: It is recommended to use WEP-OPEN because it is known to be more secure than
Shared Key.
Default Key: Select the WEP Key from the drop down list to use
Network Key 1-4
oThis is where you enter the WEP key needed for a computer to connect to the
router wirelessly
oYou can define up to 4 passwords or 4 keys. Only one key can be active at a given
time. Most users simply define one key.
oChoose a key index 1, 2, 3, or 4 and enter the key.
oWhen connecting to the router, the client must match both the password and the
Key number. (e.g. if you have activated Key 2 with a password of 12345, then the
client must select: Key 2 (entering Key 1, 3, or 4 will block the ability to connect)
and enter password 12345)
Note: It is recommended to use 128-bit format because it is more secure to use a
key that consists of more characters.
HEX or ASCII: Select which WEP code type to assign
Selecting WPA- Personal, WPA2- Personal, WPA2- Personal, or Mixed (WPA2-PSK
recommended): In the Security Mode drop-down list, select WPA-Personal
WEP Key Format
HEX
ASCII
Character set
0-9 & A-F, a-f only
Alphanumeric (a,b,C,?,*, /,1,2, etc.)
64-bit key length
10 characters
5 characters
128-bit key length
26 characters
13 characters

© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-755AP
14
The following section outlines options when selecting WPA-Personal, WPA2- Personal,
or WPA2- Personal Mixed (Preshared Key Protocol),
WPA Cipher: Select a Cipher Type to use. When selecting WPA-PSK security, it is
recommended to use TKIP + AES.
oWhen selecting WPA2- Personal Mixed security, it is recommended to use
TKIP+AES.
oWhen selecting WPA2- Personal security, it is recommended to use AES.
Pre-Shared Key: Enter the passphrase or password
oThis is the password or key that is used to connect your computer to this router
wirelessly
Note: 8-63 alphanumeric characters (a,b,C,?,*, /,1,2, etc.)
Key Update Interval: Enter the time interval (seconds) of when the network
passphrase will rotate.
Note: It is recommended to use the default interval time. Your passphrase will not
change, rotation of the key is part of the WPA protocol and designed to increase
security.
Selecting WPA-Enterprise, WPA2-Enterprise, or WPA2-Enterprise Mixed:
The following section outlines options when selecting WPA-Enterprise. WPA2-
Enterprise or WPA2-Enterprise Mixed known as EAP (Extensible Authentication
Protocol). Also known as called Remote Authentication Dial-In User Service or RADIUS.
Note: This security type requires an external RADIUS server, PSK only requires you to
create a passphrase.
WPA Cipher: Select a Cipher Type to use. When selecting WPA-PSK security, it is
recommended to use TKIP + AES.
Key Update Interval: Enter the time interval (seconds) of when the network
passphrase will rotate.
Note: It is recommended to use the default interval time. Your passphrase will not
change, rotation of the key is part of the WPA protocol and designed to increase
security.
IP Address: Enter the IP address of the RADIUS server. (e.g. 192.168.10.250)
Port: Enter the port your RADIUS server is configured to use for RADIUS
authentication.
Note: It is recommended to use port 1812 which is typical default RADIUS port.
Shared Secret: Enter the shared secret used to authorize your router with your
RADIUS server.

© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-755AP
15
Connect wireless devices using WPS
WPS (Wi-Fi Protected Setup) is a feature that makes it easy to connect devices to your
wireless network. If your wireless devices support WPS, you can use this feature to
easily add wireless devices to your network.
Note: You will not be able to use WPS if you set the SSID Broadcast setting to Disabled or
if you are using WEP security.
There are two methods the WPS feature can easily connect your wireless devices to
your network.
Push Button Configuration (PBC) method
oWPS Software/Virtual Push Button - located in router management page
PIN (Personal Identification Number) Method - located in router management page
Note: Refer to your wireless device documentation for details on the operation of
WPS.
For connecting additional WPS supported devices, repeat this process for each
additional device.
PBC (Software/Virtual Push Button)
Wireless > WPS
In addition to the hardware push button located physically on your router, the router
management page also has push button which is a software or virtual push button you
can click to activate WPS on your router.
1. Log into your router management page (see “Access the management page” on page
16).
2. Click on the Wireless 2.4GHz
3. Click on WPS to configure the selected wireless band’s WPS feature. Click Apply to
save settings
WPS Config
WPS: Select enable to turn on WPS feature
WPS External Registrar Lock: Select to enable or disable external registrar feature
on the select wireless band.
WPS Summary
WPS Current Status: Displays the status of WPS feature on the selected wireless
band
WPS Configure: Displays the configured mode of the WPS feature
WPS SSID: Displays the SSID of the WPS network
WPS Security Mode: Display the security mode of the WPS network
WPS Key: Displays the security password
AP PIN: Display the WPS PIN information.
WPS Action

© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-755AP
16
PIN: Enter the PIN information of the wireless client you want to connect to the
network. Click Start PIN button to activate WPS once you enter the client’s PIN
information
Note: You may need to initiate the WPS PIN on your wireless device first when
using this method. Refer to your wireless device documentation for details on the
operation of WPS.
PBC: Click Start Push Button to activate WPS PBC configuration.
Advance configuration
Access the management page
Note: Your router management page URL/domain name http://TEW-755AP or IP
address http://192.168.10.100 is accessed through the use of your Internet web browser
(e.g. Internet Explorer, Firefox, Chrome, Safari, Opera) and will be referenced frequently
in this User’s Guide.
1. Open your web browser (e.g. Internet Explorer, Firefox, Safari, Chrome, or Opera) and
go to URL/domain name http://TEW-755AP or IP address //192.168.10.100. Your
access point will prompt you for a user name and password.
2. You can find the Password on a sticker on the side of the router and on the label on
the bottom of the router.

© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-755AP
17
3. Enter your Username and Password, select your preferred language, and then click
Login.
Operating Modes
This section outlines the available operating modes available on the access point.
1. Log into your management page (see “Access the management page” on page 16).
2. Click on System and Operation Modes.
3. Select the operating mode to apply on each wireless band.
Access Point: In this mode the device creates a wireless network to your existing
network.
Client Bridge: Select this mode to allow the access point the ability to wireless
connect to your wireless network. This is similar to a wireless laptop or mobile
device connecting to a wireless network.
WDS Access Point: In the mode the access point connects to other WDS bridge
enable devices for backbone communication and provides wireless connection to
clients (STAs) at the same time.
WDS Bridge: When this mode is selected the access point connects ONLY to other
WDS bridge enabled devices and local networks (the other wireless interface and
Ethernet interface) as a wireless backbone bridge.
WDS Station: The wireless interface connects to other WDS Bridge enabled devices
for backbone communication and connects to other wireless access points at the
same time. Use this mode to pair with the next hop access point as a WDS network
outlet.
Repeater: In this mode, the wireless interface repeats wireless signal and packets
for backbone communication as well as a client access. This feature is used to
expand your existing wireless network to areas that your current access point is
unable to reach. Make sure all of the settings of the wireless interface matches to
your root or connecting wireless access points, same SSID, channel and wireless
encryption settings.

© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-755AP
18
Access Point
Basic
Wireless > Wireless Network
This section outlines the available features to configure wireless 2.4GHz when Access
Point mode is selected.
1. Log into your management page (see “Access the management page” on page 16).
2. Click on Wireless 2.4GHz
3. Configure the below settings and click Apply to save settings.
Wireless Mode: If all of the wireless devices you want to connect with this Access
Point can connect in the same transmission mode, you can improve performance
slightly by choosing the appropriate mode. If you have some devices that use a
different transmission mode, choose the appropriate mode.
2.4GHz Wireless
oB/G/N mixed: Select this mode for the best compatibility. This mode allows older
802.11b and 802.11g wireless devices to connect to the router in addition to
newer 802.11n devices.
oB/G mixed: This mode only allows devices to connect to the router using older
and slow 802.11b or 802.11g technology and it thereby reduces the router’s
maximum speed to 54Mbps (typically not recommended).
oN only: This mode only allows newer 802.11n devices to connect to your router.
This mode does ensure the highest speed and security for your network, however
if you have older 802.11g wireless clients, they will no longer be able to connect
to this router.
oG only: This mode only allows devices to connect to the router using older and
slow 802.11g technology (typically not recommended).
oB only: This mode only allows devices to connect to the router using older and
slow 802.11b technology (typically not recommended).
Note: Please check the specifications on your wireless devices for the highest
wireless capability supported first before applying these settings. If you are
unsure, it is recommended that you keep the default setting (B/G/N mixed) for the
best compatibility.
When applying the 802.11 mode setting, please keep in mind the following:
Wireless devices that support 802.11n are backwards compatible and can
connect wirelessly at 802.11g or 802.11b.
Connecting at 802.11b or 802.11g will limit the capability of your 802.11n
supported wireless devices from obtaining higher performance and data rates.
Allowing 802.11b or 802.11g devices to connect to an 802.11n capable wireless
network may degrade the wireless network performance below the higher
performance and data rates of 802.11n.
Wireless devices that only support 802.11b or 802.11g will not be able to
connect to a wireless network that is set to 802.11n only mode.
Wireless devices that only support 802.11b will not be able to connect to a
wireless network that is set to 802.11g only mode.
Channel Width: Extension channel: When 20/40 channel bandwidth has been
chosen, you should select extension channel to get higher throughput.
Frequency (Channel): In North America, this router can broadcast on 1 of 11
Channels for 2.4GHz (13 in Europe and other countries). Selecting the Auto option
enables the router to automatically select the best Channel for wireless
communication. To manually set the channel on which the router will broadcast,
click the drop-down list and select the desired Channel for wireless communication.
The goal is to select the Channel that is least used by neighboring wireless
networks.

© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-755AP
19
Wireless Profile
Wireless 2.4GHz > Wireless Network
This section outlines the available features to configure wireless 2.4GHz when Access
Point mode is selected.
1. Log into your management page (see “Access the management page” on page 16).
2. Click on the Wireless 2.4GHz
3. Underneath the basic wireless band section, you will see Wireless Network and all
your wireless network profiles will be listed.
4. Click on the Edit button next to the wireless profile you want to configure.
5. Review the wireless settings, click Apply when finished.
SSID: Enter the wireless network name (SSID) to assign to the selected wireless
profile
Hide SSID: Select option to disable the wireless network name to broadcast
Wireless MAC filter
Wireless 2.4GHz) > Wireless MAC Filter
Every network device has a unique, 12-digit MAC (Media Access Control) address. Using
wireless MAC filters, you can allow or deny specific wireless clients using this router’s
wireless network.
1. Log into your management page (see “Access the management page” on page 16).
2. Click on the Wireless 2.4GHz.
3. Review the settings and click Apply to save settings.
Filter Mode: Select from the pull down list the MAC filter rule to apply.
oDisable: Select to turn off MAC filter feature
oDENY: Select this option to DENY all listed MAC addressed
oALLOW: Select this option to only ALLOW the listed MAC address to the the
network.
MAC Address: Enter the MAC address to apply on the MAC filter rule
MAC Filter List
MAC: List of all MAC addresses
Delete: Click to delete selected MAC address

© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-755AP
20
Client Bridge
1. Log into your management page (see “Access the management page” on page 16).
2. Click on System and Operation Modes.
3. Select the Client Bridge and click Apply.
Basic
Wireless 2.4GHz > Wireless Network
This section outlines the available features to configure wireless 2.4GHz when Access
Point mode is selected.
1. Log into your management page (see “Access the management page” on page 16).
2. Click on Wireless 2.4GHz the wireless band you would like to configure and click
Wireless Network.
3. Configure the below settings and click Apply to save settings.
Wireless Mode: Select the wireless mode to set on the selected wireless band in
client bridge mode
SSID: Manually enter the wireless network name (SSID) you want to establish
connection. Or simply click on Site Survey to scan for available wireless network.
Preferred BSSID: Click option and enter the preferred wireless network you would
like to connect to.
Security Mode: Select from the pull down menu the wireless security that is used
on the wireless network you would like to connect to.
Scan for wireless networks
Wireless 2.4GHz > Wireless Network
This section outlines the available features to configure wireless 2.4GhH when Access
Point mode is selected.
1. Log into your management page (see “Access the management page” on page 16).