TRENDnet TEW-823DAP V2 User manual

TRENDnet User’s Guide Cover Page

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide Table of contents
i
Table of Contents
Product Overview ...........................................................................1
TEW-823DAP.................................................................................................................. 1
Features ......................................................................................................................... 1
Product Hardware Features........................................................................................... 2
Application Diagram ...................................................................................................... 3
Product Overview ...........................................................................4
TEW-923DAP.................................................................................................................. 4
Features ......................................................................................................................... 4
Product Hardware Features........................................................................................... 5
Product Overview ...........................................................................6
TEW-925DAP.................................................................................................................. 6
Features ......................................................................................................................... 7
Product Hardware Features........................................................................................... 8
Getting Started .............................................................................................................. 9
Steps to improve wireless connectivity ....................................................................... 10
Connect wireless devices to your access point............................................................ 10
Configuration................................................................................11
Wireless Networking and Security .................................................12
How to choose the type of security for your wireless network .................................. 12
Secure your wireless network ..................................................................................... 13
Connect wireless devices using WPS ........................................................................... 15
Advanced configuration ................................................................16
Access the management page ..................................................................................... 16
Operating Modes......................................................................................................... 16
Access Point..................................................................................17
Basic............................................................................................................................. 17
Wireless Profile............................................................................................................ 19
MAC filter (TEW-823DAP)............................................................................................ 19
Wireless MAC Filter (TEW-923DAP / TEW-925DAP).................................................... 20
Band Steering .............................................................................................................. 21
Roaming Support (802.11k / 802.11r) ......................................................................... 21
Change your IP address ............................................................................................... 21
Reboot Schedule (TEW-823DAP)................................................................................. 22
Schedule (TEW-923DAP/TEW-925DAP)....................................................................... 22
Configure Spanning Tree ............................................................................................. 23
Set date and time ........................................................................................................ 23
Daylight Saving Time ................................................................................................... 24
NTP .............................................................................................................................. 24
Manual......................................................................................................................... 24
Management VLAN...................................................................................................... 24
Wireless Bandwidth Control........................................................................................ 25
Enable SNMP ............................................................................................................... 25
SSH Management ........................................................................................................ 26
LED Controls ................................................................................................................ 26
LLDP (TEW-923DAP / TEW-925DAP)............................................................................ 26
UPnP ............................................................................................................................ 27
Bonjour ........................................................................................................................ 27
Gateway Monitor ........................................................................................................ 27
Repeater....................................................................................... 28
Basic............................................................................................................................. 28
Scan for wireless networks .......................................................................................... 29
Advanced wireless settings ......................................................................................... 30

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide Table of contents
ii
Advanced Wireless............................................................................................. 30
Client Limit ......................................................................................................... 30
Maintenance & Monitoring ...........................................................31
Administration ............................................................................................................. 31
Timeout........................................................................................................................ 31
Device Name................................................................................................................ 31
Reset to factory defaults ............................................................................................. 31
Backup and restore your configuration settings ......................................................... 32
Restart (Reboot) access point...................................................................................... 32
Upgrade your firmware ............................................................................................... 33
Configure log................................................................................................................ 33
Diagnostics................................................................................................................... 33
Check system information ........................................................................................... 34
Check connected wireless clients ................................................................................ 35
System Log................................................................................................................... 35
Hardware Features and Specifications ........................................................................ 36
Indoor Access Point Software Specifications............................................................... 39
Troubleshooting............................................................................40
Appendix ......................................................................................41

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide Indoor Wireless Access Points
1
Product Overview
TEW-823DAP
TEW-823DAP
Package Contents
In addition to your access point, the package includes:
•TEW-823DAP
•1.64 ft. (0.5 m) network cable
•Quick Installation Guide
•Mounting plates
If any package contents are missing or damaged, please contact the retail store, online
retailer, or reseller/distributor from which the product was purchased.
Features
TRENDnet’s high-performance AC1300 Dual Band Indoor Wireless PoE Access Point,
model TEW-823DAP, supports Access Point (AP) and Repeater modes. This wireless
indoor access point generates concurrent 867Mbps WiFi AC and 400Mbps WiFi N
networks. MU-MIMO technology processes multiple data streams simultaneously,
increasing real-time WiFi performance when multiple devices access the network. The
wireless access point features access control, bandwidth control, and band steering. The
low-profile housing design blends into most environments, and includes a convenient
wall / ceiling mounting plate.
Concurrent Dual Band
AC1300: concurrent 867Mbps WiFi AC + 400Mbps WiFi N bands
Power over Ethernet (PoE)
Saves installation time and setup costs with gigabit PoE support
WiFi Operation Modes
Supports Access Point (AP) and Repeater modes
Gigabit Port
Gigabit PoE LAN port maintains a high-performance connection to the wired network
Wireless Coverage
Extended wireless coverage with MU-MIMO antenna technology
MU-MIMO Performance
MU-MIMO technology enables the access point to process multiple data streams
simultaneously, and increases real-time WiFi performance

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide Indoor Wireless Access Points
2
Band Steering
Band steering alleviates network congestion by automatically directing wireless devices
from the 2.4GHz band to the 5GHz band
Multiple SSIDs
Create up to 8 SSIDs per band (16 total)
Encrypted Wireless
Support for wireless encryption of up to WPA3
Low Profile
Low-profile housing design blends into most environments
Mounting Plate
Wall / Ceiling mounting plate
*Maximum wireless signal rates are referenced from IEEE 802.11 theoretical
specifications. Actual data throughput and coverage will vary depending on
interference, network traffic, building materials and other conditions.
Product Hardware Features
•PWR: This indicator turns blue when the device is powered.
Low-profile housing
PWR

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide Indoor Wireless Access Points
3
Gigabit PoE Port
Power port
•Gigabit PoE port: Plug an Ethernet cable (also called network cables) from
your access point to your router and wired network devices. The Gigabit port
complies with standard 802.3af/at PoE/PoE+ so you can connect to connect the AP
to a PoE switch or injector that complies with 802.3af/at.
•Power port (optional): If you are not using PoE to power the AP, you can connect
the power adapter from your access point power port to an available power outlet.
•Reset button: Use a sharp tool to press and hold this button for 15 seconds to
reset the access point.
Application Diagram
Reset button

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide Indoor Wireless Access Points
4
Product Overview
TEW-923DAP
TEW-923DAP
Package Contents
In addition to your access point, the package includes:
•TEW-923DAP
•1.64 ft. (0.5 m) network cable
•Quick Installation Guide
•Mounting plates
If any package contents are missing or damaged, please contact the retail store, online
retailer, or reseller/distributor from which the product was purchased.
Features
TRENDnet’s high-performance AX3000 Dual Band WiFi 6 PoE+ Access Point, model TEW-
923DAP, features two concurrent WiFi bands to maximize networking speeds with the
latest WiFi 6 technology. The two separate high-speed WiFi 6 bands provide speeds up
to 2402Mbps on the 5GHz band and 573Mbps on the 2.4GHz band. The access point
also supports Access Point (AP) and Repeater modes.
Faster speeds are possible on this WiFi 6 access point with 1024-QAM, OFDMA, and MU-
MIMO technologies. MU-MIMO technology processes multiple data streams
simultaneously, increasing real-time WiFi performance when multiple devices access the
network. The wireless access point features access control, bandwidth control, and band
steering. The low-profile housing design blends into most environments, and includes a
convenient wall / ceiling mounting plate.
Concurrent Dual Band
AX3000: concurrent 2402Mbps on 5GHz band + 573Mbps on 2.4GHz band
Power over Ethernet (PoE+)
Saves installation time and setup costs with 2.5GbE PoE+ support
WiFi Operation Modes
Supports Access Point (AP) and Repeater modes
MU-MIMO & OFDMA Performance
MU-MIMO technology enables the access point to process multiple data streams
simultaneously along with WiFi 6 OFDMA technology to increase real-time WiFi
performance
Band Steering
Band steering alleviates network congestion by automatically directing wireless devices
from the 2.4GHz band to the 5GHz band

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide Indoor Wireless Access Points
5
WiFi Traffic Shaping
Manage traffic allocation on the WiFi 6 access point per SSID for each band separately
Encrypted Wireless
Support for wireless encryption of up to WPA3
Multiple SSIDs
Create up to 8 SSIDs per band (16 total)
2.5GBASE-T PoE+ Port
2.5GBASE-T PoE+ LAN port maintains a high-performance connection to the wired
network
LED Control
LED control reduces product visibility by disabling the LED indicator
Low Profile
Low-profile housing design blends into most environments
Mounting Plate
Wall / Ceiling mounting plate
*Maximum wireless signal rates are referenced from IEEE 802.11 theoretical
specifications. Actual data throughput and coverage will vary depending on
interference, network traffic, building materials and other conditions.
Product Hardware Features
•PWR: This indicator turns blue when the device is powered.
Low-profile housing
PWR

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide Indoor Wireless Access Points
6
2.5GBASE-T PoE+ Port
Power port
•2.5GBASE-T PoE+ port: Plug an Ethernet cable (also called network cables) from
your access point to your router and wired network devices. The Gigabit port
complies with standard 802.3af/at PoE/PoE+ so you can connect to connect the AP
to a PoE switch or injector that complies with 802.3af/at.
•Power port (optional): If you are not using PoE to power the AP, you can connect
the power adapter from your access point power port to an available power outlet.
•Reset button: Use a sharp tool to press and hold this button for 15 seconds to
reset the access point.
Product Overview
TEW-925DAP
TEW-925DAP
Package Contents
In addition to your access point, the package includes:
•TEW-925DAP
•1.64 ft. (0.5 m) network cable
•Quick Installation Guide
•Mounting plates
If any package contents are missing or damaged, please contact the retail store, online
retailer, or reseller/distributor from which the product was purchased.
Reset button

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide Indoor Wireless Access Points
7
Features
TRENDnet’s high-performance AX5400 Dual Band WiFi 6 PoE+ Access Point, model TEW-
925DAP, features two concurrent WiFi bands to maximize networking speeds with the
latest WiFi 6 technology. The two separate high-speed WiFi 6 bands provide speeds up
to 4804Mbps on the 5GHz band and 573Mbps on the 2.4GHz band. The WiFi 6 access
point also supports Access Point (AP) and Repeater modes.
Faster speeds are possible on this WiFi 6 access point with 1024-QAM, OFDMA, and MU-
MIMO technologies. MU-MIMO technology processes multiple data streams
simultaneously, increasing real-time WiFi performance when multiple devices access the
network. The wireless access point features access control, bandwidth control, and band
steering. The low-profile housing design blends into most environments, and includes a
convenient wall / ceiling mounting plate.
Concurrent Dual Band
AX5400: concurrent 4804Mbps on 5GHz band + 573Mbps on 2.4GHz band
Power over Ethernet (PoE+)
Saves installation time and setup costs with 2.5GbE PoE+ support
WiFi Operation Modes
The 802.11ax access points supports Access Point (AP) and Repeater modes
MU-MIMO & OFDMA Performance
MU-MIMO technology enables the WiFi 6 access point to process multiple data streams
simultaneously along with WiFi 6 OFDMA technology to increase real-time WiFi
performance
Band Steering
Band steering alleviates network congestion by automatically directing wireless devices
from the 2.4GHz band to the 5GHz band
WiFi Traffic Shaping
Manage traffic allocation on the WiFi 6 access point per SSID for each band separately
Encrypted Wireless
Support for wireless encryption of up to WPA3
Multiple SSIDs
Create up to 8 SSIDs per band (16 total)
2.5GBASE-T PoE+ Port
2.5GBASE-T PoE+ LAN port maintains a high-performance connection to the wired
network
LED Control
LED control on the WiFi 6 access point reduces product visibility by disabling the LED
indicator
Low Profile
Low-profile housing design blends into most environments
Mounting Plate
The WiFi 6 access points includes a wall / ceiling mounting plate
*Maximum wireless signal rates are referenced from IEEE 802.11 theoretical
specifications. Actual data throughput and coverage will vary depending on
interference, network traffic, building materials and other conditions.

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide Indoor Wireless Access Points
8
2.5GBASE-T PoE+ Port
Power port
Product Hardware Features
•PWR: This indicator turns blue when the device is powered.
•2.5GBASE-T PoE+ port: Plug an Ethernet cable (also called network cables) from
your access point to your router and wired network devices. The Gigabit port
complies with standard 802.3af/at PoE/PoE+ so you can connect to connect the AP
to a PoE switch or injector that complies with 802.3af/at.
•Power port (optional): If you are not using PoE to power the AP, you can connect
the power adapter from your access point power port to an available power outlet.
•Reset button: Use a sharp tool to press and hold this button for 15 seconds to
reset the access point.
Low-profile housing
PWR
Reset button

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide Indoor Wireless Access Points
9
Getting Started
For a typical wireless setup at home or office when using the access point in AP mode,
please do the following:
Installation
1. Connect the power adapter to the power port of the access point. Or simply plug an
Ethernet cable on the access point to a PoE (Power over Ethernet) switch that
connects to your router or network.
2. If using the power adapter, plug an Ethernet cable to the access point and plug the
other end to your router or network.
3. Verify that all LEDs are on.
4. For your security, each access point comes pre-encrypted with a unique WiFi Name
(SSID) and WiFi Password. You can find your device's SSID and WiFi password on the
white labels located on the device. Use this information to connect to the access
point.
Note: The white label below may be different than the label included with your access
point.
5. Verify your connection to you network by accessing the Internet. For advanced
configuration continue to the advanced sections of the user manual.
Mounting device
To mount the access point, first route the network cable through the largest opening in
the mounting plate and install the mounting plate to the desired wall or ceiling using the
included drywall anchors and screws. Install the mounting plate with the correct
orientation. After the mounting plate is properly installed, connect the network cable to
the network LAN port of the access point, align the access point mounting holes with
the mounting plate clips and slide the bracket into the access point to lock into place

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide Indoor Wireless Access Points
10
Steps to improve wireless connectivity
There are a number of factors that can impact the range of wireless devices. Follow
these tips to help improve your wireless connectivity:
•Keep the number of obstructions to a minimum. Each obstruction can reduce the
range of a wireless device. Position the wireless devices in a manner that will
minimize the amount of obstructions between them.
a. For the widest coverage area, install your router near the center of your home, and
near the ceiling, if possible.
b. Avoid placing the access point on or near metal objects (such as file cabinets and
metal furniture), reflective surfaces (such as glass or mirrors), and masonry walls.
c. Any obstruction can weaken the wireless signal (even non-metallic objects), so the
fewer obstructions between the router and the wireless device, the better.
d. Place the access point in a location away from other electronics, motors, and
fluorescent lighting.
e. Many environmental variables can affect the router’s performance, so if your
wireless signal is weak, place the access point in several locations and test the signal
strength to determine the ideal position.
•Building materials can have a large impact on your wireless signal. In an indoor
environment, try to position the wireless devices so that the signal passes through
less dense material such as dry wall. Dense materials like metal, solid wood, glass or
even furniture may block or degrade the signal.
•Antenna orientation can also have a large impact on your wireless signal. Use the
wireless adapter’s site survey tool to determine the best antenna orientation for your
wireless devices.
•Interference from devices that produce RF (radio frequency) noise can also impact
your signal. Position your wireless devices away from anything that generates RF
noise, such as microwaves, radios and baby monitors.
If possible, upgrade wireless network interfaces (such as wireless cards in computers)
from older wireless standards to 802.11n. If a wirelessly networked device uses an older
standard, the performance of the entire wireless network may be slower. If you are still
experiencing low or no signal, consider repositioning the wireless devices or installing
additional access points.
Connect wireless devices to your access point
A variety of wireless network devices can connect to your wireless network such as:
•Gaming Consoles

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide Indoor Wireless Access Points
11
•Internet enabled TVs
•Network media players
•Smart Phones
•Wireless Laptop computers
•Wireless IP cameras
Each device may have its own software utility for searching and connecting to available
wireless networks, therefore, you must refer to the User’s Manual/Guide of your
wireless client device to determine how to search and connect to this router’s wireless
network.
See the “Appendix” on page 63 for general information on connecting to a wireless
network.
Configuration
Note: The access point’s default management page http://192.168.10.100 is accessed
through the use of your Internet web browser (e.g. Internet Explorer, Firefox, Chrome,
Safari, and Opera) and will be referenced frequently in this User’s Guide.
Before accessing the web-based management page, configure the IP address and
subnet mask of your computer to the following:
IP Address: 192.168.10.xxx
Subnet Mask: 255.255.255.0
1. Open your web browser (e.g. Internet Explorer, Firefox, Safari, Chrome, or Opera) and
go to “http://model number” (ie: if your AP is TEW-823DAP, type in http://tew-
823dap)or type in http://192.168.10.100.
2. Enter the default user name and password and then click Login. You can find your
device's SSID and WiFi password on the white labels located on the device. Use this
information to connect to the access point.
Wizard
1. For the first-time logging into the device the setup wizard will start automatically.
2. For your security, the first step is to change the login password of the access point.
Enter your new login password and click apply.
3. Your new password settings will be applied and you will be redirected to the login
screen. You will need to use the new login password to proceed.

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide Indoor Wireless Access Points
12
Wireless Networking and Security
How to choose the type of security for your wireless network
Setting up wireless security is very important. Leaving your wireless network open and
unsecure could expose your entire network and personal files to outsiders. TRENDnet
recommends reading through this entire section and setting up wireless security on your
new access point.
There are a few different wireless security types supported in wireless networking each
having its own characteristics which may be more suitable for your wireless network
taking into consideration compatibility, performance, as well as the security strength
along with using older wireless networking hardware (also called legacy hardware).
It is strongly recommended to enable wireless security to prevent unwanted users from
accessing your network and network resources (personal documents, media, etc.).
In general, it is recommended that you choose the security type with the highest
strength and performance supported by the wireless computers and devices in your
network. Please review the security types to determine which one you should use for
your network.
Wireless Encryption Types
•WPA/WPA2-Personal: This setting provides the router with the ability to detect
wireless devices using either WPA or WPA2 encryption. Your wireless network will
automatically change the encryption setting based on the first wireless device
connected. For example, if the first wireless client that connects to your wireless
network uses WPA encryption your wireless network will use WPA encryption. Only
when all wireless clients disconnect to the network and a wireless client with WPA2
encryption connects your wireless network will then change to WPA2 encryption.
Note: WPA2 encryption supports 802.11n speeds and WPA encryption will limit
your connection speeds to 54Mbps
•WPA2-Personal: This is the most secure wireless encryption available today, similar
to WPA encryption but more robust. This encryption standard also supports the
highest connection speeds. TRENDnet recommends setting your router to this
encryption standard. If you find that one of your wireless network devices does not
support WPA2 encryption, then set your router to either WPA or WPA-Auto
encryption.
Note: Check the specifications of your wireless network adapters and wireless
appliances to verify the highest level of encryption supported.Below is brief
comparison chart of the wireless security types and the recommended
configuration depending on which type you choose for your wireless network.
•WPA3-Personal: This is the latest wireless encryption. It is similar to WPA2
encryption, but more robust. This encryption standard also supports the highest
possible connection speed. TRENDnet recommends setting your router to this
encryption standard. If you find that one of your wireless network devices does not
support WPA3 encryption, then set your router to either WPA2 or WPA encryption.
•WPA2/WPA3-Personal: This setting provides the router with the ability to detect
wireless devices using either WPA2 or WPA3 encryption. Your wireless network will
automatically change the encryption setting based on the first wireless device
connected.
Note: Check the specifications of your wireless network adapters and wireless
appliances to verify the highest level of encryption supported.Below is brief
comparison chart of the wireless security types and the recommended
configuration depending on which type you choose for your wireless network
Security Standard
WPA
WPA2
WPA3
Compatible
Wireless
Standards
IEEE 802.11a/b/g
(802.11n devices
will operate at
802.11g to connect
using this standard)
IEEE 802.11a/b/g/n
IEEE 802.11 n/ac/ax
Highest
Performance
Under This
Setting
Up to 54Mbps
Up to 450Mbps
(11n) and up to
1.3Gbps (11ac)*
Up to 600Mbps (11n)
and up to 4.8Gbps
(11ax)*
Encryption
Strength
Medium
High
Highest
Additional
Options
TKIP or AES,
Preshared Key or
RADIUS
TKIP or AES,
Preshared Key or
RADIUS
AES
Recommended
Configuration
TKIP
Preshared Key
8-63 characters
AES
Preshared Key
8-63 characters
AES
Preshared Key
8-63 characters
*Dependent on the maximum 802.11n/ac/ax data rate supported by the device
(150Mbps, 300Mbps, 450Mbps, 867Mbps, 1.3Gbps, 2.4Gbps, or 4.8Gbps)

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide Indoor Wireless Access Points
13
Secure your wireless network
Wireless (2.4GHz or 5GHz)> Security
After you have determined which security type to use for your wireless network (see
“How to choose the security type for your wireless network” on page 12), you can set up
wireless security.
1. Log into your management page (see “Access the management page” on page 13).
2. Click on the Wireless 2.4GHz or 5GHz.
3. Underneath the wireless band section, you will see the Current Profiles of all your
wireless network listed.
4. Select the desired Security Mode from the drop down menu and enter the password
in the Password field.
Note: To select an encryption mode not included in the Security Mode drop down, click
on Edit to select another encryption mode.
5. Click Apply then click the Save button on the top-right when finished.
Selecting WPA-Enterprise, WPA2-Enterprise, or WPA2-Enterprise Mixed:
The following section outlines options when selecting WPA/WPA2-Enterprise, WPA2-
Enterprise or WPA3-Enterprise known as EAP (Extensible Authentication Protocol). Also
known as called Remote Authentication Dial-In User Service or RADIUS.
Note: This security type requires an external RADIUS server, PSK only requires you to
create a passphrase.
•WPA Cipher:Select a Cipher Type to use. When selecting WPA-PSK security, it is
recommended to use TKIP + AES.
•Key Update Interval: Enter the time interval (seconds) of when the network
passphrase will rotate.
Note: It is recommended to use the default interval time. Your passphrase will not
change; rotation of the key is part of the WPA protocol and designed to increase
security.
•IP Address:Enter the IP address of the RADIUS server. (e.g. 192.168.10.250)
•Port: Enter the port your RADIUS server is configured to use for RADIUS
authentication.
Note: It is recommended to use port 1812 which is typical default RADIUS port.

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide Indoor Wireless Access Points
14
•Shared Secret:Enter the shared secret used to authorize your router with your
RADIUS server.

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide Indoor Wireless Access Points
15
Connect wireless devices using WPS
WPS (Wi-Fi Protected Setup) is a feature that makes it easy to connect devices to your
wireless network. If your wireless devices support WPS, you can use this feature to
easily add wireless devices to your network.
Note: You will not be able to use WPS if you set the SSID Broadcast setting to Disabled or
if you are using WEP security.
There are two methods the WPS feature can easily connect your wireless devices to
your network.
•Push Button Configuration (PBC) method
oWPS Software/Virtual Push Button - located in the management page
•PIN (Personal Identification Number) Method - located in the management page
Note: Refer to your wireless device documentation for details on the operation of
WPS.
For connecting additional WPS supported devices, repeat this process for each
additional device.
PBC (Software/Virtual Push Button)
Wireless (2.4GHz or 5GHz)> WPS
In addition to the hardware push button located physically on your router, the router
management page also has push button which is a software or virtual push button you
can click to activate WPS on your router.
1. Log into your management page (see “Access the management page” on page 13).
2. Click on the Wireless network you want to configure button (Wireless 2.4GHz or
5GHz) and click WPS.
3. Click on WPS to configure the selected wireless band’s WPS feature. Select Enabled to
enable WPS on the selected wireless band.
4. Click Apply then click the Save button on the top-right when finished.
WPS Config
•WPS External Registrar Lock: Select to enable or disable external registrar feature
on the select wireless band.
WPS Summary
•WPS Current Status: Displays the status of WPS feature on the selected wireless
band
•WPS Configure: Displays the configured mode of the WPS feature
•WPS SSID: Displays the SSID of the WPS network
•WPS Security Mode: Display the security mode of the WPS network
•WPS Key: Displays the security password
•AP PIN: Display the WPS PIN information.

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide Indoor Wireless Access Points
16
WPS Action
•PIN: Enter the PIN information of the wireless client you want to connect to the
network. Click Start PIN button to activate WPS once you enter the client’s PIN
information
Note: You may need to initiate the WPS PIN on your wireless device first when
using this method. Refer to your wireless device documentation for details on the
operation of WPS.
•PBC: Click Start Push Button to activate WPS PBC configuration.
Advanced configuration
Access the management page
1. Open your web browser (e.g. Internet Explorer, Firefox, Safari, Chrome, or Opera) and
go to “http://model number” (ie: if your AP is TEW-823DAP, type in http://tew-
823dap)or type in http://192.168.10.100.
2. Enter the default user name and password and then click Login. You can find your
device's SSID and WiFi password on the white labels located on the device. Use this
information to connect to the access point.
3. Enter your Username and Password, select your preferred language, and then click
Login.
Operating Modes
This section outlines the available operating modes available on the access point.
1. Log into your management page (see “Access the management page” on page 13).
2. Click on System and Operation Mode.

© Copyright 2023 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide Indoor Wireless Access Points
17
3. Select the operating mode to apply on each wireless band.
•Access Point: In this mode, the device creates a wireless network to your existing
network.
•Repeater: In this mode, the wireless interface repeats wireless signal and packets
for backbone communication as well as a client access. This feature is used to
expand your existing wireless network to areas that your current access point is
unable to reach. Make sure all of the settings of the wireless interface matches to
your root or connecting wireless access points, same SSID, channel and wireless
encryption settings.
4. Click Apply then click the Save button on the top-right when finished.
Access Point
Basic
Wireless (2.4GHz or 5GHz) > Wireless Network
This section outlines the available features to configure for both wireless 2.4Ghz and
5GHz when Access Point mode is selected.
1. Log into your management page (see “Access the management page” on page 13).
2. Click on the wireless band you would like to configure and click Wireless Network.
3. Configure the below settings and click Save to save settings.