Tripp Lite PDUMH30AT User manual

1
Owner’s Manual
Single-Phase PDUs with
Automatic Transfer Switch
Models:
PDUMH30AT, PDUMH30ATNET, PDUMH30HVAT, PDUMH30HVATNET,
PDUMH32HVAT, PDUMH32HVATNET
Agency Model Numbers:
AGAC8033 • AGAC8034 • AGAC8110 • AGAC8073 • AG-0150 • AG-0151
Important Safety Instructions 2
Installation 3
Mounting the PDU 3
Connecting the PDU 6
Features 7
LED Diagrams 12
Configuration and Operation 16
Automatic Transfer Switch 16
Service 19
Warranty and Product Registration 20
Español 21
Français 41
Русский 61
Deutsch 81
PROTECT YOUR INVESTMENT!
Register your product for quicker service
and ultimate peace of mind.
You could also win an
ISOBAR6ULTRA surge protector—
a $100 value!
www.tripplite.com/warranty
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2019 Tripp Lite. All rights reserved.
18-11-326-93323D.indb 1 2/26/2019 3:08:17 PM

2
Important Safety Instructions
SAVE THESE INSTRUCTIONS
This manual contains instructions and warnings that should be
followed during the installation, operation and storage of this
product. Failure to heed these instructions and warnings may
affect the product warranty.
• The PDU provides the convenience of multiple outlets, but DOES NOT provide surge
or line noise protection for connected equipment.
• The PDU is designed for indoor use only, in a controlled environment, away from
excess moisture, temperature extremes, conductive contaminants, dust or direct
sunlight.
• Keep indoor ambient temperature between 32°F and 104°F (0°C and 40°C).
• The PDU must be installed by a qualified technician only.
• Do not attempt to mount the PDU to an insecure or unstable surface.
• Install in accordance with National Electrical Code standards. Be sure to use the
proper overcurrent protection for the installation, in accordance with the plug/
equipment rating.
• Connect the PDU to an outlet that is in accordance with your local building codes
and that is adequately protected against excess currents, short circuits and earth
faults.
• The electrical outlets supplying power to the equipment should be installed near the
equipment and easily accessible.
• Do not connect the PDU to an ungrounded outlet or to extension cords or adapters
that eliminate the connection to ground.
• Be sure to provide a local disconnect device on any models that are permanently
installed without a plug that is easily accessible.
• Never attempt to install electrical equipment during a thunderstorm.
• Individual equipment connected to the PDU should not draw more current than the
individual PDU’s outlet’s rating.
• The total load connected to the PDU must not exceed the maximum load rating for
the PDU.
• Do not attempt to modify the PDU, input plugs or power cables.
• Do not drill into or attempt to open any part of the PDU housing. There are no user-
serviceable parts inside.
• Do not attempt to use the PDU if any part of it becomes damaged.
• Use of this equipment in life support applications where failure of this equipment
can reasonably be expected to cause the failure of the life support equipment or to
significantly affect its safety or effectiveness is not recommended.
18-11-326-93323D.indb 2 2/26/2019 3:08:17 PM

1A
2A
3
Installation
Mounting the PDU
The PDU supports 2U rack mounting or surface mounting (e.g. on a wall, on a desk
or under a counter).
Note: The user must determine the fitness of hardware and procedures before mounting. The PDU and
included hardware are designed for common rack and rack enclosure types and may not be appropriate for all
applications. Exact mounting configurations may vary.
2U Rack Mounting
1A Attach the included mounting
brackets to the sides of the PDU
with the included screws.
2A After attaching the brackets,
position the PDU in the rack and
install four user-supplied screws
through the bracket ears and into
the rack rails.
18-11-326-93323D.indb 3 2/26/2019 3:08:18 PM

2B
3B
3B
Installation continued
1B
4
Wall Mounting (not applicable to series AG-0151 for PDUMH32HVAT &
PDUMH32HVATNET)
1B Attach one of the supplied
mounting brackets to the wall with
user supplied screws. Make sure
screws and any other hardware
are appropriate for the surface
type.
2B Attach a mounting bracket to the
PDU with the included screws.
3B Place the PDU on the wall-
mounted bracket and secure the
PDU to the bracket and wall as
shown.
18-11-326-93323D.indb 4 2/26/2019 3:08:20 PM

1C
2C
Installation continued
5
Surface Mounting
1C Attach the included mounting
brackets to the sides of the PDU
with the included screws. Note: If
you need to change the
orientation of the PDU to match
the mounting surface, rotate the
mounting brackets in 90°
increments as required before
attaching.
2C Mount the PDU to a stable surface
by inserting four user-supplied
screws through the bracket ears
and into appropriate mounting
holes. Make sure the mounting
surface and screws are capable of
supporting the combined weight of
the PDU and any attached
equipment cords.
3C Attach Cord Retention Brackets
(Optional): Attach the cord
retention brackets to the PDU with
the included screws.
3C
18-11-326-93323D.indb 5 2/26/2019 3:08:23 PM

Installation continued
1
2
To UPS
To UPS A
B
6
Connecting the PDU
Note: The PDU includes two input power cords: Primary and Secondary. They should be connected to two
separate AC power sources.
PDUMH30AT
Model
Shown
1Connect PDU Input Plugs: Connect the
Primary input plug Ato a preferred
source of grounded AC power (120V for
PDUMH30AT & PDUMH30ATNET;
200-240V for PDUMH30HVAT,
PDUMH30HVATNET, PDUMH32HVAT &
PDUMH32HVATNET), such as a Tripp Lite
SmartOnline®UPS System. Under
normal operating conditions, the PDU
will distribute AC power from the Primary
input source. Connect the Secondary
input plug Bto an alternative source of
grounded AC power (120V for
PDUMH30AT & PDUMH30ATNET;
200-240V for PDUMH30HVAT,
PDUMH30HVATNET, PDUMH32HVAT &
PDUMH32HVATNET), For proper ATS
(automatic transfer switch) function, do
not plug the Secondary input into the
same power source as the Primary input.
The PDU will distribute AC power from
the Secondary input only if the Primary
input becomes unavailable due to an
outage or power quality problem. (See
Configuration and Operation section
for more information about the ATS
function.)
2Connect Equipment to the PDU: Do
not exceed the total load rating of the
PDU or output load bank. The connected
equipment load will be displayed on the
digital load meter in amperes.
3Cord Retention (Optional): If you
connected the cord retention brackets to
the PDU, attach each equipment power
cord to a cord retention bracket by
looping the cord and securing it to an
attachment point with one of the
included cable ties. Make sure that each
power cord can be unplugged from the
PDU without removing the cable tie.
3
PDUMH30AT Model Shown
18-11-326-93323D.indb 6 2/26/2019 3:08:24 PM

Bank 1
Bank 2
Output Breaker
Bank 1 Output Breaker
Bank 2
Config Port
20A Max load per bank
Outlet type C19/16A, C13/10A
Primary
Input
Secondary
Input
Bank
1
Bank
2
Bank 1
Bank 2
Output Breaker
Bank 1 Output Breaker
Bank 2
Config Port
20A Max load per bank
Outlet type C19/16A, C13/10A
Primary
Input
Secondary
Input
Bank
1
Bank
2
Bank 1
Bank 2
Output Breaker
Bank 1 Output Breaker
Bank 2
Config Port
20A Max load per bank
Outlet type C19/16A, C13/10A
Primary
Input
Secondary
Input
Bank
1
Bank
2
3
4
4
7
7
6
6
3
PDUMH30AT
PDUMH30HVAT
PDUMH32HVAT
1
1
1
2
2
2
3
3
3
3
5
5
5
6
7
8
8
8
8
4
7
Features
18-11-326-93323D.indb 7 2/26/2019 3:08:26 PM

Features continued
8
Bank 1
Bank 2
Output Breaker
Bank 1 Output Breaker
Bank 2
Config Port
PDUMH30ATNET
PDUMH30HVATNET
PDUMH32HVATNET
2 1
1
1
2
2
3
3
3
3
4
4
4
3
3
3
5
5
5
6
7
7
7
8
8
8
8
6
6
91011
9
9
10
10
11
11
18-11-326-93323D.indb 8 2/26/2019 3:08:28 PM

9
Features continued
1Primary Input Cord
The cord is permanently attached to the PDU and has a NEMA L5-30P
(PDUMH30AT & PDUMH30ATNET) or NEMA L6-30P (PDUMH30HVAT &
PDUMH30HVATNET) twist-lock plug or IEC309 32A (PDUMH32HVAT &
PDUMH32HVATNET) plug.
2Secondary Input Cord
The cord is permanently attached to the PDU and has a NEMA L5-30P
(PDUMH30AT & PDUMH30ATNET) or NEMA L6-30P (PDUMH30HVAT &
PDUMH30HVATNET) twist-lock plug or IEC309 32A (PDUMH32HVAT &
PDUMH32HVATNET) plug.
3(PDUMH30ATNET, PDUMH30HVATNET, PDUMH32HVATNET) Switched
Outlets: During normal operation, the outlets distribute AC power to connected
equipment. The NEMA 5-15/20R, L5-30R, IEC-320-C13, IEC-320-C19 and
L6-30R outlets may be switched On and Off via software control. When an outlet
is live, the associated LED illuminates.
(PDUMH30AT, PDUMH30HVAT, PDUMH32HVAT) Unswitched Outlets: The
NEMA 5-15/20R, L5-30R, IEC-320-C13, IEC-320-C19 and L6-30R outlets
receive power from either input source, but are not individually switchable.
IEC-320-C13 Outlets
(PDUMH30HVAT,
PDUMH30HVATNET,
PDUMH32HVAT &
PDUMH32HVATNET):
10A (200-240V)
IEC-320-C19 Outlets
(PDUMH30HVAT,
PDUMH30HVATNET,
PDUMH32HVAT &
PDUMH32HVATNET:
16A (200-240V)
NEMA 5-15/20R
Outlets (PDUMH30AT
& PDUMH30ATNET)
20A (120V)
NEMA L5-30R Outlet
(PDUMH30AT &
PDUMH30ATNET)
30A (120V)
NEMA L6-30R Outlet
(PDUMH30HVAT &
PDUMH30HVATNET)
30A (200-240V)
4Factory Port: This port is reserved for configuration by factory authorized
personnel only. Do not connect anything to this port.
18-11-326-93323D.indb 9 2/26/2019 3:08:29 PM

Features continued
5Digital LED Display and
Load Meter (Ammeter)
A3-Digit Display: Shows measured
or calculated amperage, kilowatt or
voltage values.
BEnter Button: Scroll through
DISPLAY and CONFIGURATION
options using this button. While in
DISPLAY mode, a short press
switches the display between
AMPS, KW and VOLTS. While in
CONFIGURATION mode, a long
press changes configuration items
(TEMPERATURE, AUTO SCROLL, LED
BRIGHTNESS). Pressing the Enter
button and Mode button
simultaneously displays the unit’s IP
address (select models).
CMode Button: A short press of this button cycles through each of the modes
(PRIMARY, SECONDARY, BANK, TEMP*, HUMIDITY*) of the present category
(DISPLAY or CONFIGURATION) for both primary and secondary inputs. A long
press switches between DISPLAY and CONFIGURATION. Pressing the Mode
button and Enter button simultaneously displays the unit’s IP address (select
models).
*TEMP/HUMIDITY only available if optional ENVIROSENSE module is attached.
DActive Input LEDs: Indicate whether the primary or secondary active input is
powering the output.
E2-Digit Display: Indicates whether the value shown on the 3-digit display
represents primary, secondary, bank, temperature or humidity.
Display Modes:
P: The 3-digit display is showing information related to the primary AC input.
(Unit LEDs dictate what data is shown.)
S: The 3-digit display is showing information related to the secondary AC input.
(Unit LEDs dictate what data is shown.)
b ‘n’: The 3-digit display is showing information related to the output bank
number (‘n’).
t ‘n’: The 3-digit display is showing temperature for sensor (‘n’). (Units for F or C
are configured in CONFIGURATION mode.)
h ‘n’: The 3-digit display is showing humidity for sensor (‘n’).
FUnits LEDs: The AMPS, KW and VOLT LEDs are used to illustrate the units of
data displayed on the 3-digit display.
Amp LED: When selected, the load is displayed in amps on the 3-digit display.
kW LED: When selected, the load is displayed in kilowatts on the 3-digit display.
Volt LED: When selected, the voltage is displayed on the 3-digit display.
ACTIVE INPUT
PRIMARY SECONDARY
AMP
b = BANK
t = TEMP
h = HUMIDITY
P = PRIMARY
S = SECONDARY
VOLT KW
B
D
E
C
F
A
10
18-11-326-93323D.indb 10 2/26/2019 3:08:29 PM