Triton ENVi GEENVF93 User manual

2181706B - December 2023
Accessory Instructions
Please read this book thoroughly and familiarise yourself with all instructions before
commencing installation.
Keep these instructions in a safe place for future reference.

2
CONTENTS
IMPORTANT SAFETY ADVICE
The shower heads and hoses supplied with this product are a safety critical
part of your shower system. Failure to use genuine Triton parts may cause
injury and invalidate your guarantee.
Page
DuElec®Dual Outlet Kit Components ...........................................
Single Outlet Ceiling Fed Kit Components ...................................
Single Outlet Wall Fed Kit Components .......................................
Single Outlet Fixed Head Kit Components ...................................
Bulkhead Components ....................................................................
General Installation ........................................................................
Installing DuElec®Dual Outlet Kit ................................................
Installing Single Outlet Ceiling Fed Kit ........................................
Installing Single Outlet Wall Fed Kit ..............................................
Installing Single Outlet Fixed Head Kit ........................................
3
4
5
6
7
8
9
14
21
23

3
A
E
C
D
B
F
A. Diverter Valve
B. Lower Shower Arm
C. Top Fixing/Shower Arm Holder
D. Top Shower Arm
E. Shower Head Holder
F. Hose Retainer
G. Fixed Head
H. Shower Head
I. Hose (Short)
J. Hose (long)
K. Bulkhead
G
I
J
DUELEC®DUAL OUTLET KIT
H
K
Main Components

4
A
E
C
D
B
F
A. 940mm Riser Rail Section
B. 700mm Riser Rail Section
C. Guide Bracket
D. Bridging Bracket
E. Shower Head Holder
F. Hose Retainer
G
I
J
SINGLE OUTLET CEILING FED KIT
H
K
G. Bottom Bracket
H. Bracket End Trim
I. Ceiling Trim
J. Spacer (optional)
K. Outlet Connector
L. Securing Clip
M. Shower Head
N. Shower Hose
H
H
J
J
L
M
N
Main Components

5
A
E
C
D
B
F
A. Top Wall Bracket
B. Top Bracket
C. Top Trim
D. Shower Head Holder
E. Adaptor
F. Hose Retainer
G
I
SINGLE OUTLET WALL FED KIT
H
K
G. Bottom Bracket (water outlet)
H. Bottom Trim
I. Riser Rail
J. Shower Head
K. Shower Hose
J
Main Components

6
A
C
B
A. Ceiling Trim
B. Ceiling Arm
C. Fixed Head
SINGLE OUTLET FIXED HEAD KIT
K
Main Components

7
BULKHEAD
Main Components
A
B
C
D
A. Bulkhead
B. Mounting Plate
C. Adaptor
D. Trim

8
Please use this book in conjunction with the main installation guide supplied with
your ENVi®shower.
Any riser rail kit or pipework MUST not be positioned where it will be subjected to
freezing conditions.
The shower head holder can be orientated such that the shower head can be
positioned either side of the riser rail or shower arm.
DO NOT position any shower head or fixed head in such a way that water is
sprayed directly onto the ENVi®controller.
If installing a DuElec®diverter valve, ensure that the diverter valve is mounted
within 350mm radius of the water outlet, this will ensure the short shower hose
provided is able to be connected to the bulkhead provided without strains or kinks.
The edges of the riser rail are extremely sharp. Take care when handling and
cutting the rails.
Check there are no hidden cables or pipes before drilling holes for wall plugs.
Use great care when using power tools near water. The use of a Residual Current
Device (RCD) is recommended.
Before drilling holes in the ceiling or wall surface make sure there is enough
clearance above the ceiling to accommodate the entry of any riser rail and heated
water pipe.
The following requirements must be met for future servicing purposes:
• The Tri-HUB MUST NOT be covered with any form of insulating material that
may give rise to electrical circuits overheating during periods of high ambient
temperature.
• A safe means of access MUST be provided into the loft, e.g. via a xed loft ladder.
• The Tri-HUB MUST be installed vertically in an accessible and safe location.
• Ceiling joists MUST be adequately boarded to provide safe and unobstructed
access to, from and around the Tri-HUB.
• There MUST be adequate lighting in the loft for servicing purposes.
GENERAL INSTALLATION

9
1
StepStep
Mark the wall fixing position for the
Diverter Fixing Bracket and drill and
plug the wall. Ideally the hole should be
positioned in the centre of a tile and not in
the grouting.
Remove the Diverter Fixing Bracket from
the Diverter Valve and secure it to the wall
using the fixing screw.
2
StepStep
728 mm
Measure a
distance of
728mm from the
Diverter Bracket,
ensuring centres
are vertically
aligned, and mark
the position.
Drill and plug
the wall. Secure
the Shower Arm
Fixing Bracket to
the wall using the
fixing screw.
Ensure the grub
screw is pointing
downwards.
3
StepStep
Assemble the Hose Retainer onto the
Lower Shower Arm.
4
StepStep
Assemble the Shower Head Holder onto the
Lower Shower Arm.
NOTE: The Shower Head Holder can be
orientated such that the Shower Head can be
positioned either side of the Shower Arm.
INSTALLING DUELEC®DUAL OUTLET KIT

10
Assemble the Top Shower Arm into the Shower Arm Holder, note that the Top Shower Arm
can only be assembled one way, so ensure that the flat faces of Top Shower Arm and Shower
Arm Holder are aligned.
Assemble the Lower Shower Arm to Top Shower Arm by rotating the Lower Shower Arm on
to the threaded spigot. Hand tight will be sufficient to seal the two together.
Finally tighten the grub screw (located inside the bore of the Shower Arm Holder) to lock the
Top Shower Arm to Shower Arm Holder.
Flat
Face Grub
Screw
Top
Shower
Arm
Lower
Shower
Arm
Shower
Arm
Holder
Threaded
Nut
Threaded
Spigot
Ø24 x 3mm
Seal
Threaded
Nut
Threaded
Spigot
Ø24 x 3mm
Seal
5
StepStep
6
StepStep
Slide the Diverter Valve onto the Valve Fixing
Bracket and tighten the 2 x grub screwson
the underside of the Diverter Valve.
NOTE: Do not fully tighten the screws as some
adjustment of the valve will be necessary
when assembling the Shower Arms.
7
StepStep
Position the Ø24 x 3mm rubber seal on top
of the threaded Diverter Valve spigot.
Loosely tighten the threaded nut of the
Lower Shower Arm onto the Diverter
Valve.
DO NOT fully tighten the threaded nut at
this stage.