Trotec TTK 165 ECO User manual

TRT-BA-TTK165ECO/TTK170ECO-TC-001-EN
TTK 165 ECO / TTK 170 ECO
EN
OPERATING MANUAL
DEHUMIDIFIER

1 EN
Operating manual – dehumidifier TTK 165 ECO / TTK 170 ECO
Table of contents
Notes regarding the operating manual.................................1
Safety .....................................................................................1
Information about the device................................................3
Transport and storage...........................................................5
Assembly and installation.....................................................5
Operation ...............................................................................9
Available accessories..........................................................11
Errors and faults..................................................................11
Maintenance ........................................................................12
Technical annex...................................................................16
Disposal ...............................................................................17
Notes regarding the operating manual
Symbols
Warning of electrical voltage
This symbol indicates dangers to the life and health of
persons due to electrical voltage.
Warning
This signal word indicates a hazard with an average
risk level which, if not avoided, can result in serious
injury or death.
Caution
This signal word indicates a hazard with a low risk
level which, if not avoided, can result in minor or
moderate injury.
Notice
This signal word indicates important information (e.g.
material damage), but does not indicate hazards.
Info
Information marked with this symbol helps you to carry
out your tasks quickly and safely.
Follow the manual
Information marked with this symbol indicates that the
operating manual must be observed.
You can download the current version of the operating manual
and the EU declaration of conformity via the following link:
TTK 165 ECO
http://hub.trotec.com/?id=40461
TTK 170 ECO
http://hub.trotec.com/?id=40716
Safety
Read this manual carefully before starting or using the
device. Always store the manual in the immediate vicinity
of the device or its site of use!
Warning
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may
result in electric shock, fire and/ or serious injury.
Save all warnings and instructions for future
reference.
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children
without supervision.
• Do not use the device in potentially explosive rooms.
• Do not use the device in aggressive atmosphere.
• Set the device up in an upright and stable position.
• Let the device dry out after a wet clean. Do not operate it
when wet.
• Do not use the device with wet or damp hands.
• Do not expose the device to directly squirting water.
• Never insert any objects or limbs into the device.
• Do not cover or transport the device during operation.
• Do not sit on the device.

EN 2
Operating manual – dehumidifier TTK 165 ECO / TTK 170 ECO
• This appliance is not a toy! Keep away from children and
animals. Do not leave the device unattended during
operation.
• Check accessories and connection parts for possible
damage prior to every use of the device. Do not use any
defective devices or device parts.
• Ensure that all electric cables outside of the device are
protected from damage (e.g. caused by animals). Never
use the device if electric cables or the power connection
are damaged!
• The electrical connection must correspond to the
specifications in chapter Technical data.
• Insert the mains plug into a properly secured mains
socket.
• Observe the device's power input, cable length and
intended use when selecting extensions to the power
cable. Completely unroll extension cables. Avoid electrical
overload.
• Before carrying out maintenance, care or repair work on
the device, remove the mains plug from the mains socket.
Hold onto the mains plug while doing so.
• Switch the device off and disconnect the power cable from
the mains socket when the device is not in use.
• Do not under any circumstances use the device if you
detect damages on the mains plug or power cable.
If the supply cord is damaged, it must be replaced by the
manufacturer, his service agent or similarly qualified
persons in order to avoid a hazard.
Defective power cables pose a serious health risk.
• Observe the storage and operating conditions (see chapter
Technical data).
• Ensure that the air inlet and outlet are not obstructed.
• Ensure that the side of the device where the air inlet is
found is kept free of dirt and loose objects.
• Only transport the device in an upright position with an
emptied condensation tank or drain hose.
• Discharge the collected condensate before transport and
storage. Do not drink it. Health hazard!
Intended use
Only use the device for drying and dehumidifying room air, while
adhering to and following the technical data.
Intended use comprises:
• dehumidifying and drying:
– living rooms, bedrooms, bathrooms and basements
– laundries, holiday homes, camper vans, boats
• maintaining the dryness of:
– storage spaces, archives, laboratories, garages
– bathrooms, wash rooms, changing rooms etc.
Improper use
• Do not place the device on wet or flooded ground.
• Do not place any objects, e.g. clothing, on the device.
• Do not use the device outdoors.
• Any unauthorised modifications, alterations or structural
changes to the device are forbidden.
• Any operation other than as described in this manual is
prohibited. Non-observance renders all claims for liability
and guarantee null and void.
Personnel qualifications
People who use this device must:
• be aware of the dangers that occur when working with
electric devices in damp areas.
• have read and understood the operating manual, especially
the Safety chapter.
Maintenance tasks which require the housing to be opened
must only be carried out by specialist companies for cooling and
air-conditioning or by Trotec.

3 EN
Operating manual – dehumidifier TTK 165 ECO / TTK 170 ECO
Residual risks
Warning of electrical voltage
Work on the electrical components must only be
carried out by an authorised specialist company!
Warning of electrical voltage
Before any work on the device, remove the mains plug
from the mains socket!
Hold onto the mains plug while pulling the power cable
out of the mains socket.
Warning
Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!
Warning
The device is not a toy and does not belong in the
hands of children.
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
Notice
Do not operate the device without an inserted air filter!
Without the air filter, the inside of the device will be
heavily contaminated. This could reduce the
performance and result in damage to the device.
Behaviour in the event of an emergency
1. In an emergency, disconnect the device from the mains
feed-in: Switch the device off and disconnect the power
cable from the mains socket. Hold onto the mains plug
while doing so.
2. Do not reconnect a defective device to the mains.
Information about the device
Description of the device
The device uses the principle of condensation to automatically
dehumidify rooms.
The fan sucks damp room air through the air inlet, the air filter,
the evaporator and to the condenser located behind it. The air is
cooled at the cold evaporator until it is below the dew point.
Water vapour contained in the room air precipitates on the
evaporator fins as condensation or rime. The dehumidified,
cooled air is slightly warmed at the condenser and blown out
again. The drier air thus conditioned mixes with the air in the
room. The humidity in the room where the device is positioned
is reduced as air constantly circulates through the device.
Depending on the air temperature and the relative humidity, the
condensed water either drops continuously or only during the
defrost phase through the integrated drain nozzle into the
condensation tank below. It is fitted with a float to measure the
filling level.
In case of the device TTK 165 ECO defrosting takes place
electronically in air circulation mode.
The device TTK 170 ECO comes with a hot gas automatic
defrost system. Here, the hot gas of the refrigerant circuit is
used actively for fast and effective defrosting. This makes the
device TTK 170 ECO considerably more effective at
temperatures below 15°C.
If the maximum filling level of the condensation tank is reached
or if the condensation tank is not installed correctly, the device
will react as follows:
In case of the device TTK 170 ECO the condensation tank
indicator light will light up (see chapter Device depiction).
In case of the device TTK 165 ECO an acoustic signal will be
emitted.
The compressor and fan will switch off. The condensation tank
indicator light or the acoustic signal only goes off again once the
emptied condensation tank is reinserted.
If required, an external hygrostat can be connected to the device
TTK 170 ECO for controlling the humidity level. Moreover, an
operating hours counter helps you to meet the maintenance
deadlines.
Optionally, the condensed water can be drained by attaching a
hose at the condensation connection.
The device can reduce the relative humidity of a room to
approx. 30%.
Because of the heat radiation generated during operation, the
room temperature may rise slightly.

EN 4
Operating manual – dehumidifier TTK 165 ECO / TTK 170 ECO
Info
The illustrations in this operating manual feature the
device TTK 170 ECO by way of example. The
represented operating steps and explanations,
however, also apply to device TTK 165 ECO unless
otherwise mentioned.
Device depiction
1
2
3
4
10
11
12
13
TTK 170 ECO
1
2
3
4
10
TTK 165 ECO
5
6
9
8
7
5
TTK 165 ECO / TTK 170 ECO
No. Designation
1 Transport handle
2 Air inlet with air filter
3 Condensation tank (behind cover)
4 Feet
5 Air outlet
6 Power cable holder
7 Wheels
8 Air filter
9 Condensation drain hose connection
10 On/off switch
11 Condensation tank indicator light
12 Operating hours counter
13 Connection for optional external hygrostat

5 EN
Operating manual – dehumidifier TTK 165 ECO / TTK 170 ECO
Transport and storage
Notice
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
Transport
Before transporting the device, proceed as follows:
• Switch off the device.
• Hold onto the mains plug while pulling the power cable out
of the mains socket.
• Drain the remaining condensate from the device and the
condensation drain hose (see chapter Maintenance).
• To make the device easier to transport, it is fitted with
wheels.
• Do not incline the device by more than 45°, for otherwise
the device could be damaged.
• Do not use the power cable to drag the device.
• Only wheel the device on a level and smooth surface.
After transporting the device, observe the following:
• Set up the device in an upright position after transport.
• Leave the device to rest for 12to24hours, so the
refrigerant can accumulate within the compressor. Wait
12to24hours before switching the device back on! Acting
contrary might lead to compressor damage and a
malfunctioning device. If so, any warranty claims will be
voided.
Storage
Before storing the device, proceed as follows:
• Drain the remaining condensate from the device and the
condensation drain hose (see chapter Maintenance).
• Empty and clean the condensation tank prior to storage.
When the device is not being used, observe the following
storage conditions:
• dry and protected from frost and heat
• in an upright position where it is protected from dust and
direct sunlight
• with a cover to protect it from invasive dust if necessary
• Place no further devices or objects on top of the device to
prevent it from being damaged.
Assembly and installation
Scope of delivery
• 1x Device
• 1x Air filter
• 2x Transport wheel
• 1x Axle
• 2x Wire clip
• 2 x Linchpin
• 4x Washer
• 1 x Transport handle
• 2 x Foot
• 2 x Large screw
• 10 x Small screw
• 1x Manual
Unpacking the device
1. Open the cardboard box and take the device out.
2. Completely remove the packaging.
3. Fully unwind the power cable. Make sure that the power
cable is not damaged and that you do not damage it during
unwinding.

EN 6
Operating manual – dehumidifier TTK 165 ECO / TTK 170 ECO
Assembly
Use tools suitable for the intended task.
Mounting the feet
Prior to initial start-up, the feet must be attached to the device.
To do so, please proceed as follows:
1. Place the device on its front side.
2. Mount the two feet(4) to the device sides using six screws.
The feet must protrude from the bottom side of the device.
4
4
4
3. Then mount the wheels.
Mounting the wheels
Prior to initial start-up, the transport wheels and the axle must
be attached to the device. To do so, please proceed as follows:
üThe device is placed on its front side.
1. Use two large screws to fasten the axle(14) to the rear
bottom side of the device. Ensure tight fit.
14
2. Insert a wire clip(15) into the inner hole of the axle up to
the stop. Bend the end of the wire clip outwards to fix the
wire clip.
15

7 EN
Operating manual – dehumidifier TTK 165 ECO / TTK 170 ECO
3. Place a washer(16) on the axle(14).
4. Place a wheel(7) in front of the washer(16).
5. Place a second washer(16) in front of the wheel(7).
7
14
16
16
6. Insert a linchpin(17) into the hole in front of the washer(16)
up to the stop. Turn over the ring of the linchpin(17).
17
17
16
7. Repeat this process on the other side of the axle.
8. After mounting the wheels and the feet, place the device in
an upright position.
Notice
Leave the device to rest for 12to24hours, so the
refrigerant can accumulate within the compressor.
Wait 12to24hours before switching the device back
on! Acting contrary might lead to compressor damage
and a malfunctioning device. If so, any warranty claims
will be voided.
Mounting the transport handle
Prior to initial start-up, the transport handle must be attached to
the device. To do so, please proceed as follows:
1. Mount the handle(1) to both feet(4) using four screws.
1
4

EN 8
Operating manual – dehumidifier TTK 165 ECO / TTK 170 ECO
Start-up
When positioning the device, observe the minimum distance
from walls or other objects as described in the Technical data
chapter.
A
B
C
C
D
• Before restarting the device, check the condition of the
power cable. If there are doubts as to the sound condition,
contact the customer service.
• Set the device up in an upright and stable position.
• Do not create tripping hazards when laying the power
cable or other electric cables, especially when positioning
the device in the middle of the room. Use cable bridges.
• Make sure that extension cables are completely unrolled.
• When positioning the device, keep a sufficient distance to
heat sources.
• Make sure that no curtains or other objects interfere with
the air flow.
• When positioning the device, particularly in wet areas,
secure it locally with an RCD (residual current device)
which complies with the respective regulations.
• Do not incline the device by more than 45°, for otherwise
the device could be damaged.
Inserting the air filter
Notice
Do not operate the device without an inserted air filter!
Without the air filter, the inside of the device will be
heavily contaminated. This could reduce the
performance and result in damage to the device.
• Make sure that the air filter is installed before switching
the device on.
Inserting the condensation tank
• Ensure that the float inside the condensation tank is
inserted correctly.
• Ensure that the condensation tank is empty and inserted
correctly.
Connecting the power cable
• Insert the mains plug into a properly secured mains
socket.

9 EN
Operating manual – dehumidifier TTK 165 ECO / TTK 170 ECO
Operation
Notes:
• Avoid open doors and windows.
• After being switched on, the device operates fully
automatically.
• The compressor switches on approx.3minutes after the
device has been switched on.
• The fan continuously runs in dehumidification mode until
the device is switched off.
Switching the device on
Once you have completely installed the device as described in
the Start-up chapter, you can switch it on.
Notice
Only use the device in an upright position, otherwise
the compressor could be damaged.
1. Press the on/off switch(10).
ðThe device starts to dehumidify.
Memory function
After a power failure during operation the device will
automatically be switched back on after a while.
Auto stop function
If the water tank is full or not inserted correctly, the device will
stop automatically.
Operating hours counter
The device TTK 170 ECO is equipped with an operating hours
counter(12). The hour display has five digits.
Operation with hose attached to the condensation
connection
For continuous operation or unattended dehumidification, please
connect a suitable condensation drain hose to the device.
üA suitable hose (diameter: 12mm) is ready for use.
üThe device is switched off.
1. Open the front cover.
2. Remove the condensation tank.
3. Guide the condensation drain hose through the hole in the
device's bottom panel.
4. Push one end of the hose onto the hose connection at the
condensation tank.

EN 10
Operating manual – dehumidifier TTK 165 ECO / TTK 170 ECO
5. Refit the condensation tank into the device. Guide the other
hose end to a suitable drain or sufficiently dimensioned
collection container.
6. Please observe that the hose must not be kinked.
Remove the hose if you want to collect the condensate in the
condensation tank again. Allow the hose to dry prior to storage.
Automatic defrost
At low ambient temperatures, ice may form at the evaporator
during dehumidification. The device will then carry out an
automatic defrost. Dehumidification is briefly interrupted during
defrosting. The fan keeps running.
In case of the device TTK 165 ECO defrosting takes place
electronically in air circulation mode. In defrost mode, the
compressor switches off while the fan keeps running and
circulates the compressor's waste heat around the evaporator
for defrosting.
The device TTK 170 ECO comes with a hot gas automatic
defrost system based on the bypass procedure. Here, the hot
gas of the refrigerant circuit is used actively for fast and
effective defrosting. As soon as ice starts to form, a special
valves opens automatically, redirects the hot gas to the
evaporator, and closes again after defrosting is completed so
that drying operation can be continued via the regular
refrigerant circuit. Unlike air circulation defrosting, hot gas
automatic defrosting allows for considerably shorter defrost
phases, which is an essential requirement for effective
dehumidification in low-temperature surroundings (below 15°C)
such as unheated rooms. After all, the actual dehumidification
process only takes place when defrosting is not in progress.
The duration of the defrost process can vary. Do not switch off
the device during automatic defrost. Do not remove the mains
plug from the mains socket.
External hygrostat (optional)
The device TTK 170 ECO allows for the connection of an
external hygrostat. The desired humidity can be regulated by
use of a hygrostat. The external hygrostat is connected to the
connection for the external hygrostat(13). For further
information, e.g. on the type of hygrostat, please contact the
customer service.
Shutdown
Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
• Switch off the device.
• Hold onto the mains plug while pulling the power cable out
of the mains socket.
• If necessary, remove the condensation drain hose and any
residual fluid from it.
• Empty the condensation tank, if need be.
• Clean the device according to the Maintenance chapter.
• Store the device according to the Storage chapter.

11 EN
Operating manual – dehumidifier TTK 165 ECO / TTK 170 ECO
Available accessories
Warning
Only use accessories and additional equipment
specified in the operating manual.
Using insertion tools or accessories other than those
specified in the operating manual may cause a risk of
injury.
Designation Article number
Hygrostat HG110 with jack plug 6.100.002.044
Errors and faults
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
The device does not start:
• Check the power connection.
• Check the power cable and mains plug for damages.
• Check the on-site fusing.
• Check the filling level of the condensation tank and empty
it if necessary. In case of the device TTK 170 ECO the
condensation tank indicator light(11) must not light up. In
case of the device TTK 165 ECO the acoustic signal must
not be emitted.
• Check the condensation tank for correct seating.
• Check the room temperature. Observe the device's
permissible operating range according to the technical
data.
• Wait for 10minutes before restarting the device. If the
device is not starting, have the electrics checked by a
specialist company or by Trotec.
The device is running, but there is no formation of
condensate:
• Check the float in the condensation tank for dirt. If
necessary, clean the condensation tank. The float must be
able to move freely.
• Check the room temperature. Observe the device's
permissible operating range according to the technical
data.
• Ensure that the relative room humidity complies with the
technical data.
• Check the air filter for dirt. If necessary, clean or replace
the air filter.
• From the outside, check the condenser for dirt (see
chapter Maintenance). If the condenser is dirty, have it
cleaned by a specialist company or by Trotec.
• The device might carry out an automatic defrost. During
automatic defrost, the device does not dehumidify.
The device is loud or vibrates:
• Check whether the device is set up in a stable and upright
position.
Condensate is leaking:
• Check the device for leaks.
The compressor does not start:
• Check the room temperature. Observe the device's
permissible operating range according to the technical
data.
• Ensure that the relative room humidity complies with the
technical data.
• Check whether the overheating protection of the
compressor has tripped. Disconnect the device from the
mains and let it cool down for approx. 10minutes before
reconnecting it.
• The device might carry out an automatic defrost. During
automatic defrost, the device does not dehumidify.
The device gets very warm, is loud or loses power:
• Check the air inlets and air filter for dirt. Remove external
dirt.
• From the outside, check the device for dirt (see chapter
Maintenance). If the inside of the device is dirty, have it
cleaned by a specialist company for cooling and air-
conditioning or by Trotec.
Notice
Wait for at least 3 minutes after maintenance and
repair work. Only then switch the device back on.
Your device still does not operate correctly after these
checks?
Please contact the customer service. If necessary, bring the
device to a specialist company for cooling and air-conditioning
or to Trotec for repair.

EN 12
Operating manual – dehumidifier TTK 165 ECO / TTK 170 ECO
Maintenance Maintenance intervals
Maintenance and care interval before every
start-up
as needed at least every
2 weeks
at least every
4 weeks
at least every
6 months
at least
annually
Empty condensation tank and drain
hose
X
Check the air inlets and outlets for
dirt and foreign objects and clean if
necessary
X X
Clean the exterior X X
Visually check the inside of the
device for dirt
X X
Check the air filter for dirt and
foreign objects and clean or
replace if necessary
X X
Replace air filter X
Check for damage X
Check the attachment screws X X
Test run X

13 EN
Operating manual – dehumidifier TTK 165 ECO / TTK 170 ECO
Maintenance and care log
Device type: ............................................. Device number: ....................................
Maintenance and care interval 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Empty condensation tank and drain
hose
Check the air inlets and outlets for
dirt and foreign objects and clean if
necessary
Clean the exterior
Visually check the inside of the
device for dirt
Check the air filter for dirt and
foreign objects and clean or
replace if necessary
Replace air filter
Check for damage
Check the attachment screws
Test run
Remarks:
1. Date: ................................
Signature: ............................
2. Date: ................................
Signature: ............................
3. Date: ................................
Signature: ............................
4. Date: ................................
Signature: ............................
5. Date: ................................
Signature: ............................
6. Date: ................................
Signature: ............................
7. Date: ................................
Signature: ............................
8. Date: ................................
Signature: ............................
9. Date: ................................
Signature: ............................
10. Date: ..............................
Signature: ............................
11. Date: ..............................
Signature: ............................
12. Date: ..............................
Signature: ............................
13. Date: ..............................
Signature: ............................
14. Date: ..............................
Signature: ............................
15. Date: ..............................
Signature: ............................
16. Date: ..............................
Signature: ............................

EN 14
Operating manual – dehumidifier TTK 165 ECO / TTK 170 ECO
Activities required before starting maintenance
Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
• Switch off the device.
• Hold onto the mains plug while pulling the power cable out
of the mains socket.
Warning of electrical voltage
Tasks which require the housing to be opened
must only be carried out by authorised specialist
companies or by Trotec.
Cleaning the housing
Clean the housing with a soft, damp and lint-free cloth. Ensure
that no moisture enters the housing. Protect electrical
components from moisture. Do not use any aggressive cleaning
agents such as cleaning sprays, solvents, alcohol-based or
abrasive cleaners to dampen the cloth.
Visual inspection of the inside of the device for dirt
1. Remove the air filter.
2. Use a torch to illuminate the openings of the device.
3. Check the inside of the device for dirt.
4. If you see a thick layer of dust, have the inside of the device
cleaned by a specialist company for cooling and air-
conditioning or by Trotec.
5. Put the air filter back in.
Refrigerant circuit
• The entire refrigerant circuit is a maintenance-free,
hermetically sealed system and may only be maintained or
repaired by specialist companies for cooling and air-
conditioning or by Trotec.
Cleaning the air filter
Notice
Ensure that the air filter is not worn or damaged. The
corners and edges of the air filter must not be
deformed or rounded. Before reinserting the air filter,
make sure that it is undamaged and dry!
The air filter has to be cleaned as soon as it is dirty. This is
brought to light e.g. by a reduced capacity (see chapter Errors
and faults).
1. Remove the air filter from the device.
2. Clean the filter using a slightly damp, soft, lint-free cloth. If
the filter is heavily contaminated, clean it with warm water
mixed with a neutral cleaning agent.
3. Allow the filter to dry completely. Do not insert a wet filter
into the device!

15 EN
Operating manual – dehumidifier TTK 165 ECO / TTK 170 ECO
4. Reinsert the air filter into the device.
Emptying the condensation tank
If the condensation tank is full or not inserted correctly, the
device will react as follows:
In case of the device TTK 170 ECO the condensation tank
indicator light(11) will light up.
In case of the device TTK 165 ECO an acoustic signal will be
emitted.
The compressor and fan will switch off.
1. Take the condensation tank out of the device.
2. Empty the condensation tank over a drain or sink.
3. Rinse the tank with clear water. Clean the tank regularly
using a mild cleaning agent (no detergent!).
4. Refit the condensation tank into the device.
Make sure not to damage the float when inserting or
removing the condensation tank.
In doing so, make sure that the float is positioned correctly.
Also make sure that the condensation tank is inserted
correctly, otherwise the device cannot be switched back on.
Activities required after maintenance
If you want to continue using the device:
• Leave the device to rest for 12to24hours, so the
refrigerant can accumulate within the compressor. Wait
12to24hours before switching the device back on! Acting
contrary might lead to compressor damage and a
malfunctioning device. If so, any warranty claims will be
voided.
• Reconnect the device to the mains.
If you do not intend to use the device for a considerable time:
• Store the device according to the Storage chapter.

EN 16
Operating manual – dehumidifier TTK 165 ECO / TTK 170 ECO
Technical annex Technical data
Model TTK165ECO TTK170ECO
Max. dehumidification performance 52 l / 24 h 52 l / 24 h
Dehumidification performance @ 30°C
and 80%RH
50l / 24 h 50l / 24 h
Air flow rate 350 m3/h 350 m3/h
Ambient temperature 5°C to 32°C 5°C to 32°C
Operating range 30 % to 90 % RH 30% to 90% RH
Mains connection 1/N/PE ~ 220V – 240V / 50 Hz 1/N/PE ~ 220V – 240V / 50 Hz
Power input 0.92 kW 0.9 kW
Nominal current 3.6 A 4.2 A
Refrigerant R410A R410A
Amount of refrigerant 400 g 405 g
GWP factor 2088 2088
CO2 equivalent 0.84t 0.85t
Condensation tank capacity 5 l 6.6 l
Sound pressure level (1m distance) 56 dB(A) 56 dB(A)
Dimensions (depth x width x height) 525 x 462 x 930 mm 495 x 455 x 900 mm
Minimum distance to walls and other
objects
top (A):
rear (B):
sides (C):
front (D):
50 cm
50 cm
50 cm
50 cm
50 cm
50 cm
50 cm
50 cm
Weight 30 kg 31 kg
Wiring diagram
TTK165ECO TTK170ECO

17 EN
Operating manual – dehumidifier TTK 165 ECO / TTK 170 ECO
Disposal
The icon with the crossed-out waste bin on waste
electrical or electronic equipment stipulates that this equipment
must not be disposed of with the household waste at the end of
its life. You will find collection points for free return of waste
electrical and electronic equipment in your vicinity. The
addresses can be obtained from your municipality or local
administration. For further return options provided by us please
refer to our website www.trotec24.com.
The separate collection of waste electrical and electronic
equipment aims to enable the re-use, recycling and other forms
of recovery of waste equipment as well as to prevent negative
effects for the environment and human health caused by the
disposal of hazardous substances potentially contained in the
equipment.
You are responsible for deleting any personal data stored on the
waste equipment to be disposed of.
The device is operated with fluorinated greenhouse gas which
can be dangerous for the environment and contribute to global
warming when emitted to the atmosphere.
Further information is provided on the nameplate.
Dispose of the refrigerant appropriately and according to the
national regulations.

Trotec GmbH & Co. KG
Grebbener Str. 7
D-52525 Heinsberg
[phone]
[phone]
[email protected]
www.trotec.com