Truma CP classic Instruction sheet

Page 47
TR
Gebrauchsanweisung Seite 2
Einbauanweisung Seite 11
Im Fahrzeug mitzuführen!
Operating instructions Page 13
Installation instructions Page 22
To be kept in the vehicle!
Mode d‘emploi Page 24
Instructions de montage Page 33
À garder dans le véhicule !
Istruzioni per l‘uso Pagina 35
Istruzioni di montaggio Pagina 44
Da tenere nel veicolo!
Truma CP (E) classic

13
Control panels CP (E) classic
Table of Contents
Symbols used ...................................................................... 14
Intended use ..................................................................... 14
Operating instructions
Safety instructions ........................................................... 15
Display and control panels ............................................. 15
Control panel – CP classic ................................................... 15
Power selector switch – CP E classic .................................. 15
Start-up .............................................................................. 16
Hot water mode .................................................................. 16
Heating and hot water mode .............................................. 16
Switching off .................................................................... 17
Fault .................................................................................... 17
Gas or diesel mode .............................................................. 17
Electrical mode .................................................................... 18
Mixed mode ........................................................................ 18
Accessories ....................................................................... 18
Troubleshooting guide (Combi Gas heating system) . 19
Troubleshooting guide (Combi Diesel heating system) . 21
Technical data ................................................................... 23
Maintenance ..................................................................... 23
Disposal ............................................................................. 23
Declaration of conformity ............................................... 23
Installation instructions
Safety instructions ........................................................... 23
Scope of delivery .............................................................. 23
Assembly ........................................................................... 24
Symbols used
The unit must only be installed and repaired by an
expert.
Note containing information and tips.
Please pay attention to the ESD regulations!
Electrostatic charge can destroy the electronics.
Ensurethat potential compensation is present before touch-
ing the electronics.
Intended use
Control panel – CP classic
The room temperature and the water temperature can be set
at a Truma Combi (E) heating system using the control panel.
Power selector switch – CP E classic
It is possible to choose between gas, diesel and/or electrical
energy at a Truma Combi (E) heating system (with heating
elements for electrical mode) using the power selector switch.
The CP classic control panel is also required.
The control panels are intended for installation in caravans
and motor homes. Installation in boats is not permitted.

14
Safety instructions
– The heating system or control panel must not be used un-
less it is in perfect working order.
– Repairs must be carried out immediately. Only carry out
repairs yourself if the solution is described in the trouble-
shooting guide of this manual.
– Do not make repairs or modifications to the heating system
or the control panel!
– A defective heating system or defective control panel may on-
ly be repaired by the manufacturer or his service department.
Display and control panels
Control panel – CP classic
1
3
5
7
9
40°
60°
60°
Combi
1
2
3
4
5
c
d
f
b
a
g, h
e
a = Control knob for room temperature (1 – 5)
b = Green LED lit, “On”
c = Hot water mode
(Water temperature 40 °C or 60 °C)
d = Heating and hot water mode
(heating without water temperature monitoring or with
drained water system)
Operating instructions e = Heating and hot water mode
(heating with water temperature monitoring)
f = Rotary switch “Off”
g = Yellow LED lit, “Boiler heat-up phase”
yellow LED flashing “Warning”
r = Red LED lit, red LED flashing “Fault”
Power selector switch – CP E classic
Combi E
230 V~
m
l
n
o
j
k
i
i = Power selection rotary switch
j = Electrical mode 230 V, 1800 W
k = Electrical mode 230 V, 900 W
l = Gas or diesel mode
m= Mixed mode* (gas, diesel or electrical mode 900 W)
n = Mixed mode* (gas, diesel or electrical mode 1800 W)
o = Yellow LED lit = “Electrical mode”
* Hot water mode
In hot water mode the heating system automatically selects
electrical mode at the preselected electrical power setting of
900 W or 1800 W.
Heating mode:
Electrical mode has priority in heating mode. If the electrical
heating output is insufficient, gas or diesel mode is enabled.
Switching on the electric heating elements as well
does not increase the maximum heating power.

15
Start-up
Heating mode is possible with or without water
content depending on the operating mode.
Hot water mode
This operating mode can only be used if the boiler has
been filled.
Devices with electrical heating elements
Select diesel or electrical mode using the power selector
switch. Illumination of the yellow LED (o) at the power se-
lector switch indicates that the unit is operating with 230 V.
Mixed mode (gas or diesel and electrical mode) is not
possible in hot water mode. With this setting the unit
automatically selects electrical mode with a preselected
power setting of 900W or 1800W.
Move the rotary switch on the control panel to position
(c-hot water mode) 40 °C or 60 °C. The green (b) and
yellow(g) LEDs light up.
After reaching the set water temperature (40 °C or 60 °C), the
heating system will switch off and the yellow LED (g) will be
extinguished.
Heating and hot water mode
Devices with electrical heating elements
Select gas, diesel, electrical or mixed mode using the power
selector switch. Illumination of the yellow LED (o) at the
power selector switch indicates that the unit is operating
with 230 V.
– Heating with water temperature monitoring
Move rotary switch on control panel to “On” position (e).
Set the rotary switch (a) to the desired thermostat setting
(1 – 5). The green LED (b) for operation is lit and simultaneous-
ly indicates the position of the selected room temperature. The
yellow LED (g) indicates the water‘s heat-up phase.
The unit automatically selects the required operating level
according to the temperature difference between the set-
ting on the control panel and the current room temperature.
When the room temperature selected on the control panel is
reached, the heating system switches back to the smallest
setting and heats the water to 60 °C. Once the water tem-
perature is reached, the heating system switches off and the
yellow LED (g) goes out.
– Heating without water temperature monitoring
Move rotary switch on control panel to “On” position (d).
Set the rotary switch (a) to the desired thermostat setting
(1 – 5). The green LED (b) for operation is lit and simultaneous-
ly indicates the position of the selected room temperature. The
yellow LED (g - water heat-up phase) will be lit only when the
water temperature is below 5 °C!

16
The unit automatically selects the required operating level
according to the temperature difference between the setting
on the control panel and the current room temperature. Once
the room temperature selected on the control panel has been
reached, the heating system switches off. The warm air fan
will continue to run at a low speed as long as the blow-out
temperature (on the unit) is higher than 40 °C.
If the boiler has been filled, the water is automatically heat-
ed as well. The water temperature is then dependent on the
heating output being given off, and the duration of heating
required to reach the desired room temperature.
– Heating with drained water system
Move rotary switch on control panel to "On" position (d).
Set the rotary switch (a) to the desired thermostat setting
(1 – 5). The green LED (b) for operation is lit and simultaneous-
ly indicates the position of the selected room temperature. The
yellow LED (g) will only be lit if the temperature of the unit is
below 5 °C!
Depending on the operating mode, the unit will automatically
select the required operating level according to the tempera-
ture difference between the setting on the control panel and
the current room temperature. Once the room temperature
selected on the control panel has been reached, the heating
system switches off. The warm air fan will continue to run at a
low speed as long as the blow-out temperature (on the unit) is
higher than 40 °C.
Switching off
Switch off heating system at control panel using rotary switch
(position f). The green LED (b) goes off.
Always drain water contents if there is a risk of frost!
Units with gas mode
If the unit is not going to be used for a long period of time,
close the quick-acting valve in the gas supply line and turn
off the gas cylinder.
Fault
Gas or diesel mode
In the event of a fault the red LED (h) or the yellow LED (g) on
the control panel will flash.
Possible causes can be found in the troubleshooting guide.
A reset (fault reset) is carried out by switching off, waiting
until all LED’s on the control panel have stopped flashing, and
then switching the heating system on again.
If the window to which a window switch is mounted is
opened, the heater stops operating and the yellowLED (g)
flashes 3 times. The heater continues operating when the win-
dow is closed.

17
Electrical mode
The yellow LED (o) goes off on the power selector switch,
and the yellow LED (g) or the red LED (h) flashes on the
control panel.
Possible causes can be found in the troubleshooting guide.
If the 230 V power supply is interrupted for just a brief
period of approximately 1 second during operation, the
heating system will subsequently resume in electrical mode.
Mixed mode
Fault in the 230 V power supply
The yellow LED (o) on the power selector switch goes off and
the yellow LED (g) on the control panel flashes 2 x.
Possible causes can be found in the troubleshooting guide.
If the 230 V power supply is interrupted during mixed mode,
the heating system will automatically switch to gas mode.
Assoon as the 230 V power supply is restored, the heating
system automatically switches back to mixed mode.
Fault in the combustion procedure
The yellow LED (o) on the power selector switch illuminates
and the red LED (h) or the yellow LED (g) on the control panel
flashes.
Possible causes can be found in the troubleshooting guide.
If the flame goes out during mixed mode (e.g. empty gas cylin-
der or closed exhaust outlet), the heating system automatically
switches to electrical mode. For the heating system to operate
in mixed mode again, the cause of the fault must be remedied
and the control panel switched off and on again (fault reset).
Accessories
Cover frames are available as accessories in the colours agate
grey, black, beige, platinum and gold.
Matching side parts are available for the control panels in
8 different colours, and create a visually attractive finish.
Please contact your specialist dealer in this connection.
Line-up clip, 1 piece (part no. 34000-65900). For installing sev-
eral Truma control panels next to each other.
Other accessories (without picture) for control panel:
– 3 m control panel cable (part no. 36110-01)
– 6 m control panel cable (part no. 36110-02)
– 9 m control panel cable (part no. 36110-03)

18
Troubleshooting guide (Combi Gas heating system)
Flashing code at analogue control panel – CP Classic
Flash sequence LED:
– On / Off: 0.5 seconds
Pause between flash sequence: 5 seconds
Fault Cause Rectification
No LED is on, the unit is switched
on and is supplied with operating
current
– Automatic restart is blocked, e.g.
after an power failure.
– Reset (fault reset) by switching off, waiting 5 seconds and then
switching on again
No LED illuminates
after switching on.
– No operating voltage
– Device fuse or vehicle fuse
defective
– Check 12 V battery voltage, charge battery if necessary
– Check all electrical plug connections
– Check fuse of unit or vehicle and replace if necessary (see fuses)
The green LED comes on when the
unit is switched on, but the heating
system does not operate
– The temperature setting on the
control panel is lower than the
room temperature
– Select higher room temperature at the control panel
After switching on the heating sys-
tem, the green LED illuminates and
the yellow LED flashes 1 x
(Heating system continues to operate)
– Risk of low voltage
Battery voltage too low
< 10.4 V
– Charge battery
yellow LED flashes 2 x
(Heating system not operating)
– Low voltage
Battery voltage too low
< 10.0 V
– Charge battery. If necessary replace old battery
– Overvoltage > 16.4 V – Check battery voltage and voltage sources such as the charger
(Only with Combi E) – No 230 V operating voltage
– 230 V fuse defective
– Overheating protection has been
triggered
– Restore 230 V operating voltage
– Replace 230 V fuse
– Reset overheating protection, allow heating system to cool,
remove connection cover and press reset button
yellow LED flashes 3 x – Open window above cowl
(window switch)
– Close window

19
Fault Cause Rectification
yellow LED flashes 4 x
(After operating for a longer pe-
riod of time, the heating system
switches to failure)
– Summer mode with empty
water container
– Switch unit off and allow to cool,
fill boiler with water
– Warm air outlets blocked – Check individual outlet apertures
– Circulated air intake blocked – Remove blockage from circulated air intake
yellow LED flashes 5 x – Room temperature sensor or
cable defective
– Please contact Truma Service
yellow LED flashes 7 x – Control panel or control panel
cable defective
– Please contact Truma Service
yellow LED flashes 8 x – FrostControl heating element
has a short circuit
– Disconnect heating element plug from electronic control unit, re-
place heating element
yellow LED flashes 9 x
(approx. 30 seconds after switch-
ing on the heating system)
– Gas cylinder or quick-acting
valve in gas supply line closed
– Check gas supply and open valves
– Gas cylinder empty – Replacing a gas cylinder
(After operating for a longer pe-
riod of time, the heating system
switches to failure)
– Gas pressure regulation system
iced up
– Use regulator heater (EisEx)
– Butane content in the gas cylin-
der too high
– Use propane (butane is unsuitable for heating, particularly at tem-
peratures below 10 °C)
Red LED flashes 1 - 8 times – Heating system fault – Please contact Truma Service.
Determine flashing code (short, long) if necessary: Red LED on
heater electronics.
Green LED flashes (with 5 Hz)
after the heating system has been
switched off
– After-running is active to reduce
the temperature of the unit
– No fault. After-run switches itself off after max. 5 minutes.
Room heating does not react to
adjustment immediately
– After-running is active to reduce
the temperature of the unit
– No fault. After-run switches itself off after max. 5 minutes
After switching on the green and
the red LED illuminate
– Faulty electronics – Please contact Truma Service
If these actions do not remedy the problem, please contact Truma Service.

20
Troubleshooting guide (Combi Diesel heating system)
Flashing code in analogue control panel – CP Classic
Flash sequence LED:
– On / Off: 0.5 seconds
Pause between flash sequence: 5 seconds
Fault Cause Rectification
No LED illuminates
after switching on.
– No operating voltage
– Device fuse or vehicle fuse
defective
– Check 12 V battery voltage, charge battery if necessary
– Check all electrical plug connections
– Check fuse of unit or vehicle, replace if necessary (see fuses)
The green LED illuminates when
the unit is switched on, but the
heating system does not operate
– The temperature setting on the
control panel is lower than the
room temperature
– Select higher room temperature at the control panel
Green LED flashes (with 5 Hz)
after the heating system has been
switched off
– After-running is active to reduce
the temperature of the unit
– No fault, after-run switches itself off after max. 5 minutes
Red LED flashes 6 x – Lack of fuel due to insufficient
fuel tank filling, tank has run
empty and / or vehicle is on a
slope
– Fill tank with fuel, then fill fuel line as described in "Initial start-up"
Red LED flashes (except 6 times)
or red LED permanently on
– Heater malfunction – Please contact Truma Service
Yellow LED flashes 1 x – Risk of low voltage
< 11.5 V
– Use the electrical power from the battery sparingly,
e.g. restrict lighting
– Charge battery
Yellow LED flashes 2 x – Undervoltage < 10.2 V – Check battery voltage, charge battery if necessary
– Short-term immediate action, switch off major consumers
or start up vehicle engine until the heating system starts running
(approx. 4 minutes)
– Battery capacity inadequate, if necessary exchange old battery

21
Fault Cause Rectification
Yellow LED flashes 2 x – Overvoltage > 16.4 V – Check battery voltage and voltage sources such as the
charger
(Only with Combi E) – No 230 V operating voltage
– 230 V fuse defective
– Overheating protection has been
triggered
– Restore 230 V operating voltage
– Replace 230 V fuse
– Reset overheating protection, allow heating system to cool,
remove connection cover and press reset button
Yellow LED flashes 3 x – Open window above cowl
(window switch)
– Close window
Yellow LED flashes 4 x – Warm air temperature and / or
water temperature exceeded:
– Not all warm air ducts are
connected
– Warm air outlets blocked
– Circulated air intake blocked
– Check whether the 4 warm air ducts are connected
– Check individual outlet apertures
– Remove blockage from circulated air intake
– Summer mode with empty
water container
– Fill boiler with water
Yellow LED flashes 5 x – Room temperature sensor or
cable defective
– Please contact Truma Service
Yellow LED flashes 6 x – Water temperature exceeded in
summer mode
– Fill boiler with water
Yellow LED flashes 7 x – Control panel or control panel
cable defective
– Please contact Truma Service
Yellow LED flashes 8 x – FrostControl heating element
has a short circuit
– Disconnect heating element plug from electronic control unit,
replace heating element
If these actions do not remedy the problem, please contact Truma Service.

22
Technical data
Dimensions (LxWxH) 53 x 53 x 44 mm
Right reserved to make technical changes!
Maintenance
The control panels are maintenance free.
Disposal
The unit must be disposed of in line with the administrative
regulations of the respective country in which it is used.
National regulations and laws (in Germany, for example, the
End-of-life Vehicle Regulation) must be observed.
Declaration of conformity
The control panels are entitled to bear the CE symbol. (Con-
formity declaration – see operating instructions of relevant
heating system)
The CE product identification number of the heating system
remains valid.

Truma Gerätetechnik GmbH & Co. KG
Wernher-von-Braun-Straße 12
85640 Putzbrunn
Deutschland
Service
Telefon [phone]
Telefax [phone]
[email protected]
www.truma.com
34030-11900 · 02 · 08/2013 ·
Bei Störungen wenden Sie sich bitte an das Truma
Servicezentrum oder an einen unserer autorisierten
Servicepartner (siehe Truma Serviceheft oder
www.truma.com).
Für eine rasche Bearbeitung halten Sie bitte Gerätetyp und
Fabriknummer (siehe Typenschild) bereit.
Always notify the Truma Service Centre or one of our
authorised service partners if problems are encountered (see
Truma Service Booklet or www.truma.com).
In order to avoid delays, please have the unit model and
factory number ready (see type plate).
Veuillez vous adresser au centre de SAV Truma ou à un de
nos partenaires de SAV agréés en cas de dysfonctionnements
(consultez votre livret de service Truma ou www.truma.com).
Pour un traitement rapide de votre demande, veuillez tenir
prêts le type d’appareil et le numéro d’usine (voir plaque
signalétique).
In caso di guasti rivolgersi al centro di assistenza Truma o a
un nostro partner di assistenza autorizzato (vedere il libretto di
assistenza Truma o il sito www.truma.com).
Affinché la richiesta possa essere elaborata rapidamente,
tenere a portata di mano il modello dell’apparecchio e il
numero di fabbrica (vedere targa dati).
©