Trumpf TruTool N 200 User manual

Operator's manual
english
TruTool N 200 (1A1)

2 Safety E521EN_04.DOC
Table of contents
1. Safety ..................................................................................3
2. Description .........................................................................5
2.1 Correct use ..........................................................................6
2.2 Technical data .....................................................................7
3. Tool assembly....................................................................8
3.1 Changing the stroke rate .....................................................8
4. Operation..........................................................................10
4.1 Working with the TruTool N 200 ........................................10
4.2 Changing the cutting direction ...........................................11
4.3 Making inner cutouts..........................................................11
4.4 Nibbling with templates......................................................12
5. Maintenance .....................................................................13
5.1 Changing the tool...............................................................14
Disassembling the punch .............................................15
Installing the punch.......................................................15
Replacing the die..........................................................15
5.2 Replacing carbon brushes.................................................15
6. Original accessories and wearing parts........................16
Warranty
Replacement parts list
Addresses

E521EN_04.DOC Safety 3
1. Safety
¾Read the Operator's Manual and the general safety rules
(Material number 1239438, red document) in their entirety
before starting up the machine. Follow precisely the directions
contained therein.
¾Read the Operator's Manual and the safety instructions
(Material number 125699, red document) in their entirety
before starting up the machine. Follow precisely the directions
contained therein.
¾The safety regulations according to DIN VDE, CEE, AFNOR
and other regulations which are valid in individual countries
should be adhered to.
Danger
Lethal danger due to electric shock!
¾Remove the plug from the plug socket before undertaking any
maintenance work on the machine.
¾Check the plug, the cable and the machine for damage each
time before the appliance is used.
¾Keep the machine dry and do not operate in damp rooms.
¾When using the electric tool outside, connect the fault current
(FI) protective switch with a maximum breaking current of
30 mA.
Warning
Danger of injury possible due to improper handling!
¾When working with the machine, wear safety glasses, hearing
protection, protective gloves and work shoes.
¾Do not plug in the plug unless the machine has been
switched off. Pull out the mains plug after use.
Warning
Risk of injury to the hands!
¾Do not place your hand into the processing line.
USA/CAN
Rest of the world

4 Safety E521EN_04.DOC
Caution
Damage to property possible due to improper handling!
The machine will be damaged or destroyed.
¾Do not use the power cord to carry the machine.
¾Always guide the electric cord away from the back of the
machine and do not pull it across sharp edges.
¾Arrange for start-ups and checks on manual electric tools to
be carried out by a trained specialist. Only used the original
accessories provided by TRUMPF.
Warning
Risk of injury from high-temperature and sharp chips!
High-temperature and sharp chips are expelled from the chip
ejector at high speed.
¾The use the chip bag is recommended.

E521EN_04.DOC Description 5
2. Description
8
6
10
11
7
4
3
2
1
5
9
1 Cover ring
2 Die
3 Punch
4 Punch guide
5 Die carrier
6 Index sleeve for direction of tool
7 Handle for tool clamping
8 On/Off switch
9 Setting wheel for speed controller
10 Max. sheet thickness 1.5 mm for
stainless steel up to 600 N/mm²
11 Max. sheet thickness 2.0 mm for
steel up to 400 N/mm²
TruTool N 200
Fig. 36729

6 Description E521EN_04.DOC
2.1 Correct use
Warning
Risk of injury!
¾For processing and materials, only use machines which are
named in "Correct use".
The TRUMPF Nibbler TruTool N 200 is an electric hand tool used
for the following applications:
•Slitting plate-shaped workpieces made of a punchable material
such as steel, aluminium, non-ferrous heavy metals, and
plastic.
•Nibbling straight or curved exterior and interior cutouts.
•Slitting tubes as well as machining sectional sheets.
•Nibbling from scribed lines or templates.
Note
The nibbling process produces cutting edges free of deformations.
Note
•Because of the hollow round punch, the nibbler can be rotated
at any position such that processing can continue mm any
direction.

E521EN_04.DOC Description 7
2.2 Technical data
Rest of the world USA
Values Values Values Values
Voltage 230 V 120 V 110 V 120 V
Frequency 50 Hz 50/60 Hz 50 Hz 50/60 Hz
Steel 400 N/mm²
Steel 600 N/mm²
Steel 800 N/mm²
Aluminium 250
N/mm²
2.0 mm
1.5 mm
1.0 mm
2.5 mm
2.0 mm
1.5 mm
1.0 mm
2.5 mm
2.0 mm
1.5 mm
1.0 mm
2.5 mm
0.08 in
0.06 in
0.039 in
0.1 in
Working speed 1.1 m/min 1.1 m/min 1.1 m/min 3.6 ft/min
Nominal power
consumption
500 W 500 W 500 W 500 W
Stroke rate with
idle run
2100/min 2000/min 2000/min 2000/min
Weight 2.2 kg 2.2 kg 2.2 kg 4.9 lbs
Start hole
diameter
16 mm 16 mm 16 mm 0.630 in
Smallest radius
with curved
cutouts
4 mm 4 mm 4 mm 0.16 in
Protective
insulation
Class II Class II Class II Class II
Technical data
Noise and vibration Measured values in accordance
with EN 60745
A-weighted sound level Typically 81 dB (A)
A-weighted acoustic power level Typically 85 dB (A)
Hand-arm vibration Typically 3.5 m/s²
Measured values for noise and vibration
Note
The measured values specified above may be exceeded while
working.
Tab. 1
Tab. 2

8 Tool assembly E521EN_04.DOC
3. Tool assembly
3.1 Changing the stroke rate
Caution
Damage to property possible resulting from stroke rate being
too low!
The motor could be damaged due to overheating!
¾Select suitable stroke rate.
1
1 Setting wheel for speed
controller on motor
Speed controller
¾Rotate the setting wheel for the speed controller counter-
clockwise.
A reduced number of strokes improves the quality of the work
•for precise machining along scribed lines.
•for machining radiuses.
•for machining steel with a tensile strength > 400 N/mm²
(improved service life).
Note
The rpm cannot be adjusted with the 120 Volt version. Work is
always performed at the maximum rpm.
Fig. 25263
Reducing the stroke rate

E521EN_04.DOC Tool assembly 9
Speed controllerSheet thickness
[mm]
max. tensile
strength
[N/mm²] Continuous
operation
Intermittent
operation
0.5 G-D C-A
1 800
(stainless steel)
G-E D-B
1.5 600
(stainless steel)
G-F E-C
2 400 (steel) G F-D
2.5 250 aluminium G F-E
Tab. 3

10 Operation E521EN_04.DOC
4. Operation
4.1 Working with the TruTool N 200
Caution
Damage to property possible due to too-high network
voltage!
Damage to the motor!
¾Check the power supply. The power supply must correspond
to the information on the machine type plate.
Warning
Danger of injury possible due to improper handling!
¾When working with the machine, always ensure that it has a
secure base.
¾Never touch the tool while the machine is running.
¾Always guide the machine away from the body while working.
¾Do not work holding the machine above your head.
¾Move the On/Off switch to the front.
Note
The cutting result is improved and the service life of the punch
increased if the cutting track is coated with oil before machining the
workpiece.
Material Oil
Steel Punching and nibbling oil, Order No.
103387
Aluminium Wisura oil, Order No. 125874
1. Do not move the machine towards the workpiece until full
speed has been reached.
2. Machine/process the material.
–Machine the desired cutting line.
3. In the event that the cutting track ends in the sheet, pull the
still-running machine a few millimetres back towards where the
cutting track has already been cut open.
4. Switch the machine off.
¾Move the On/Off switch to the rear.
Switching on the
TruTool N 200
Tab. 4
Working with the
TruTool N 200
Switching off the
TruTool N 200

E521EN_04.DOC Operation 11
4.2 Changing the cutting direction
The direction of the cut can be rotated to the right or the left in
5° increments as needed.
•For right-handed/left-handed operation.
•Machining sectional sheets.
2
1
1 Sleeve 2 Tool
1. Push the sleeve (1) up until it stops.
2. Turn the tool (2) to the desired direction.
3. Release the sleeve (1) and turn the tool (2) slightly such that it
locks into the next index position.
4.3 Making inner cutouts
¾Make a start hole at least 16 mm in diameter.
Fig. 25666

12 Operation E521EN_04.DOC
4.4 Nibbling with templates
h1
a
R1
R2
1
2
3
h2
1 Punch guide, outside diameter
13 mm
2 Workpiece
3 Template
a Clearance of the contour of the
template to the contour of the
workpiece to be nibbled out
h1 Thickness of the template
h2 Thickness of the workpiece
h1+h2 Total thickness of template
and workpiece:
5-6.5 mm
R1Minimum radius in the template
R2 Minimum radius in the workpiece
Fig. 25828

E521EN_04.DOC Maintenance 13
5. Maintenance
Danger
Possible lethal danger due to electric shock!
¾Pull the plug out of the socket when carrying out tool changes
and before all maintenance work on the machine.
Caution
Damage to property possible due to blunt tools!
Overloading of the machine.
¾Check the cutting edge of the punch hourly for wear. A sharp
punch provides good cutting performance and is easier on
the machine. Replace punches promptly.
Warning
Risk of possible injury due to improper repairs!
The machine does not function properly.
¾Repairs should be carried out only by a trained specialist.
Maintenance point Procedure and time interval Recommended lubricants Order No.
Lubrication
agents
Punch guide With each tool change Lubricating grease "G1" 121486
Gearbox and
gear head (2)
After 300 operating hours, arrange
for a trained specialist to
relubricate or to replace the
lubricating grease
Lubricating grease "G1" 139440
Punch Replace as needed - -
Die Replace as needed - -
Ventilation slots Clean as needed - -
Maintenance positions and maintenance intervals
Tab. 5

14 Maintenance E521EN_04.DOC
5.1 Changing the tool
1
2
3
4
5
6
8
9
7
S
S
F
1 Housing
2 Grip for tool clamp
3 Index pins
4 Ram with punch adapter
5 Punch
6 Tool
7 Cover ring
8 Die
9 Cylindrical pin
F Lubricating grease "G1"
S Direction of cutting
¾If the punch or die becomes blunt, change the tool.
Fig. 25655

E521EN_04.DOC Maintenance 15
Disassembling the punch
1. Pull handle (2) back.
2. Pull tool (6) out of the housing (1).
3. Remove punch (5).
Installing the punch
1. Lightly lubricate the punch (5) and the boring in the tool (6) with
lubricating grease "G1".
2. Hang the punch in the groove of the punch adapter.
3. Align the cutting direction towards the front.
4. Insert tool (6) into the housing (1) with cutting direction facing
towards the front.
5. Slide handle (2) back, the tool (6) is kept in the housing.
Replacing the die
1. Push cover ring (7) upward out of slot.
2. Push out cylindrical pin (9) using a drift punch.
3. Pull off die (8) from the carrier pin and replace it with a new
die.
4. Set die on the carrier pin.
5. Mount cylindrical pin.
6. Slide the cover ring in the nut downwards.
5.2 Replacing carbon brushes
The motor comes to a standstill when the carbon brushes are worn
out.
¾Have the carbon brushes checked and replaced as needed by
a trained technician.
Note
Only use original replacement parts and take note of the
information on the rating plate.

16 Original accessories and wearing parts E521EN_04.DOC
6. Original accessories and wearing parts
Designation Original
acces-
sories
deli-
vered
Wearing
parts
Optio-
nal
Material-
number
Punch + + 944506
Die + + 994799
Lubricating grease "G1" Tube + 344969
Case + 345243
Operator's manual + 1254080
Safety information (red
document), other countries
+ 125699
Safety information (red
document), USA
+ 1239438
Chip bag + 088622
Punching and nibbling oil for steel
(0.5 litre)
+ 103387
Torx Spanner Tx20 + 0359907
TruTool PN 200 (1A3), (1A4) + 961964
TruTool PN 161 (1A3) + 961966
Original accessories, wearing parts and optional items
To ensure fast delivery of the correct original and wearing parts:
1. Give the order number.
2. Enter further order data:
–Tension data
–Number of pieces
–Machine type
3. Give complete dispatch data:
–Correct address.
–Required delivery type (e.g. air mail, courier, express mail,
ordinary freight, parcel post).
4. Send the order to the TRUMPF representative office. For
TRUMPF service addresses, see the address list at the end of
the document.
Tab. 6
Ordering wearing parts