Trust AWST-6000 User manual

START-LINE
TRANSMITTER AWST-6000
Item 71013 Version 1.0
Visit www.trust.com
for the latest instructions
WIRELESS MOTION SENSOR
USER MANUAL
MULTI LANGUAGE

2
4
1
3

6
8
5
7
80
20

910

AWST-6000 WIRELESS MOTION SENSOR
1
1. Open the motion sensor
Use a thin screwdriver to detach the sensor from the frame.
2. Install transmitter batteries
Place 2x 1,5V AAA alkaline batteries in the battery compartments.
The polarity should match the symbols on the holder.
3. Assign code to a Trust SmartHome receiver
Assign this transmitter to the memory of one or multiple receivers, by sliding the LEARN switch from
[DEL] to [SET] to send an ON-signal. Read the receiver’s manual for the code learning procedure.
4. Set light sensitivity
Slide the [R] switch to select 1 of the 3 light sensitivity levels. [H]: Sensor is always active. [M]: Sensor is
active when the environment brightness is less than 20 lux (late afternoon). [L]: Sensor is active when
the environment brightness is less than 10 lux (late evening). If you want to control chime
ACDB-6500C, always choose [H].
5. Set switch-o delay
When no more motion is detected, the transmitter automatically sends an OFF-signal after 5 seconds
or 1/5/10 minutes.
6. Set detection range
Slide the [ ] switch to select 1 of the 3 detection ranges.
[1M]: 1-3 meters
[3M]: 1-5 meters
[6M]: 1-7 meters
EN

AWST-6000 WIRELESS MOTION SENSOR
2
7. Set detection angle
The horizontal detection angle of the sensor is maximum 80° and minimum 20°. Remove, reposition
or adjust the size of the plastic screens to change the detection angle. Next, ax the transmitter
using screws or double-sided tape.
8. Ax the transmitter using screws
1. Screw the base of the wireless motion sensor onto a flat surface, e.g. a wall.
2. Press the frame back onto the base and press the sensor into the frame.
3. The sensor needs 30 seconds to analyze its environment, before it becomes operational.
9. Ax the transmitter using double-sided tape
1. Apply double-sided tape to the back of the wireless motion sensor.
2. Stick the wireless motion sensor onto a flat surface, e.g. a closet.
3. The sensor needs 30 seconds to analyze its environment, before it becomes operational.
10. Delete code from Trust SmartHome receiver memory
Read the receiver’s manual for the single code deletion procedure. Slide the LEARN switch from [SET]
to [DEL] to send an OFF-signal.
EN

IMPORTANT INFORMATION
MULTI LANGUAGE
START-LINE
TRANSMITTER AWST-6000
Item 71013 Version 1.0
Visit www.trust.com
for the latest instructions
WIRELESS MOTION SENSOR

AWST-6000 WIRELESS MOTION SENSOR
1
EN
COMPATIBILITY
This transmitter works with all
Trust SmartHome receivers.
TECHNICAL SPECIFICATIONS
FUNCTIONALITY
Indoor motion sensor for switching 1 or more
Trust SmartHome receivers on/o. Also compatible
with the Trust SmartHome doorbell chime.
• Batteries
• RF frequency
• RF range
• Detection range
• Horizontal detection angle
• Vertical detection angle
• Switch-o delays
• Light level settings
2x 1,5 Volt AAA alkaline
433.92 MHz
Up to 30 m indoor/70 m outdoor (optimal conditions)
Up to 7 m
20° up to 80°
65°
4 (5 seconds, 1/5/10 minutes)
3 (High, Medium, Low)
REMARKS
• When changing the light sensitivity [H/M/L], the sensor needs 30 seconds to become operational again.
• When light sensitivity setting [H] is selected, the switch-o delay function is disabled.
The motion sensor sends an OFF-signal directly when no more motion is detected.
• Avoid combining this wireless motion sensor with Trust SmartHome dimmer receivers,
because the dim-mode can be activated when the dimmer receives a second on-signal.
WIRELESS RADIO SIGNAL
• The 433.92 MHz radio signal passes through walls, windows and doors.
• Indoor range: up to 30 m. Outdoor range: up to 70 m. (optimal conditions)
• The range is strongly dependent on local conditions, such as the presence of metals. For example, the thin
metal coating in Low-emissivity (Low-E) glass has a negative impact on the range of radio signals.
• There may be restrictions on the use of this device outside the EU. If applicable, check whether this device
complies with local directives.
Read these simple guidelines. Not following them may be dangerous and faulty installation will invalidate any
warranty that may apply to this product.

AWST-6000 WIRELESS MOTION SENSOR
2
EN
LEGAL INFORMATION
CE: Trust declares this device complies with the Directives as listed in Section 2 of this document.
WEEE: Dispose of the device at a recycling centre. More information: www.trust.com
Warranty information: www.trust.com/warranty
BATTERY
Remove the batteries if the product will not be used
for an extended period. Extreme temperatures reduce
the capacity and lifetime of the battery.
Replace the battery when the LED indicator in the
sensor eye starts flashing continously or when the
reach of the transmitter starts to decrease.
Do not crush, burn or shred batteries.
Dispose of batteries according to local regulations.
Please recycle when possible. Do not dispose as
household waste.
LIFE-SUPPORT
Never use Trust SmartHome products for life-support
systems or other applications in which equipment
malfunctions can have life-threatening consequences.
INTERFERENCE
All wireless devices may be subject to interference,
which could aect performance.
The minimum distance between 2 receivers should
be at least 50 cm.
REPAIRING
Do not attempt to repair this product.
There are no user-serviceable parts inside.
WATER-RESISTANCE
This product is not water-resistant.
Keep it dry. Moisture will corrode the inner electronics.
CLEANING
Use a dry cloth to clean this product. Do not use harsh
chemicals, cleaning solvents, or strong detergents.
HANDLING
Do not drop, knock, or shake the device.
Rough handling can break internal circuit boards and
fine mechanics.
ENVIRONMENT
Do not expose the product to excessive heat or cold,
as it can damage or shorten the life of electronic circuit
boards and batteries.

AWST-6000 WIRELESS MOTION SENSOR
50
EN
TRUST SMART Home
LAAN VAN BARCELONA 600
3317DD DORDRECHT
NEDERLAND
Declaration of Conformity
Trust International B.V. declares that this trust smart home-product:
Model: AWST-6000 WIRELESS MOTION SENSOR
Item number: 71013
Intended use: Indoor
is in compliance with the essential requirements and other relevant provisions of the following
directives: EMC Directive, Low Voltage Directive and R&TTE Directive.
The product is compatible with the following norms/standards:
Authorized representative
H. Donker, Procurement Director
Dordrecht, 1-1-2015
EN 300 220-1 V2.4.1 (2012-05)
EN 300 220-2 V2.4.1 (2012-05)
EN 301 489-1 V1.9.2 (2011-09)
EN 301 489-3 V1.6.1 (2013-08)
EN 61000-4-2:2009
EN 61000-4-3:2006 +A1:2008 +A2:2010
EN 62479:2010
EN 60730-1:2011