Trust WIRELESS POWER 300 Series User manual

TRUST WIRELESS POWER SYSTEM 310SY
1
UK
1 Introduction
With our TRUST WIRELESS POWER 300 series you can operate your electrical
equipment by remote control without having to get out of your chair. The WIRELESS
POWER system can be expanded with remote controls, wall switches, dimmers,
switches. Your home will become a technological complex of remote control electronic
equipment.
This manual is intended for users of the ‘TRUST WIRELESS POWER SYSTEM
310SY ‘. The WIRELESS POWER SYSTEM 310SY is a wireless switching system
that enables you to get started immediately. The system includes two wireless
switches and one remote control The switches can switch a capacity of 400 Watts.
The WIRELESS POWER 300 series has 256 channels available for optimum user
convenience and possibilities
2 Safety
Before using please read the following instructions carefully:
1. Do not use this device in damp environments such as bathrooms, swimming
pools, etc.
2. Never insert objects into the holes on the outside of this device, because you
may touch components that are live. This may cause fire or electrical shocks.
3. Do not repair this device.
4. The capacity of the device you connect to this device may not exceed the
maximum capacity specified in the technical data of this device. Connecting a
device with higher capacity may cause damage, short-circuiting or fire.
5. This product operates at 433 MHz and is approved according to the R&TTE
European standards. This equipment meets all R&TTE standards for use
within the EU. However, local restrictions may apply for the use of this
equipment. You yourself are responsible for ensuring that the use of this
equipment corresponds to local regulations. In case of doubt, contact your
government.

TRUST WIRELESS POWER SYSTEM 310SY
2
3 Installation
Note: Check the capacity of the lamp you want to connecist; you can dim and
switch a maximum of 400 Watts with the WIRELESS POWER SYSTEM
310SY dimmer.
3.1 Dimmer
1. Set your home code (A t/m P) to the WIRELESS dimmer by means of the
rotation switch on the back. Select a home code which is not in use by other
devices in your vicinity but which is the same as the one for the remote control
you are using. See figure 1.
2. Next, set the selected device code (1 through 16) with the second rotation
switch. See figure 2.
3. Plug the switch into the power outlet.
4. Next, insert the plug of the lamp you want to operate by remote control into the
dimmer. See figure 3.
5. If the lamp has its own on /off switch, switch it on.
Now you can dim the lamp you connected and switch it on and off if you have entered
the correct channel settings on your remote control.
Note: Only use dimmers with light bulbs.
Note: When using several dimmers, do not use the same device code.
3.2 Remote control
Before you can operate your devices with the WIRELESS POWER SYSTEM 310SY
remote control, the particular devices must first be connected to the Trust WIRELESS
POWER SYSTEM 3201Y switches or other receivers from the Trust power 300 series
3.2.1 Inserting the batteries
1. Remove the battery compartment cover. See figure 4.
2. Insert the 23A 12V (B) in the compartment (C) with the “+” pole to the “+” pole
of the remote control and the “-“ pole to the “-“ pole of the switch. See figure 4.
3. Replace the battery compartment cover.
Note: Remove the battery if you do not use the remote control for an
extended period.

TRUST WIRELESS POWER SYSTEM 310SY
3
UK
3.2.2 Setting the home code
In order to be able to operate them all with the remote control, it is necessary that all
receivers be set to the same home code. Set the home code as follows:
1. At the back of the remote control you will find a round rotation switch with A
through P listed on it. See figure 1.
2. Set the round rotation switch to the selected device code using a screwdriver.
Note: Set the switch you want to operate with the remote control to the same
home code.
3.2.2 Setting the device code
When you are using several receivers you that want to operate independently, you
must assign an individual device code to each one. You can set 16 device codes
within 1 home code and so operate 16 devices by remote control. When using the
correct channel settings of your Trust power 300 series switch or dimmer, you can dim
and/or switch on or off your equipment connected by remote control. Follow the points
below in conjunction with figure 5.
1. In order to operate device codes 1 through 4, set switch “B” to position A.
2. In order to operate device codes 5 through 8, set switch “B” to position B
3. In order to operate device codes 9 through 12, set switch “B” to position C.
4. In order to operate device codes 13 through 16, set switch “B” to position D.
4 System operation
Button: Description: Purpose:
AOn, off switch Switching the device code on and off.
BDimmer button Dimmer start and stop button.
CGroup selection switch Selecting among group for device code
switches. Positions: A [1-4]; B[5–8]; C[9-
12]; D[13–16]
Table 1: Button instructions. See figure 3.
1. Set the WIRELESS POWER SYSTEM 310SY dimmer to device code ‘2’, for
example. See figure 2.
2. Set button “B” in figure 5 to position A, this way you can operate device codes
1-4.
3. Switch device code “2” on and off with button “A-2” as in figure 5.
4. Start dimming by pressing button “C-2” as in figure 5 once.
5. Stop dimming by pressing button “C-2” as in figure 5 once again.

TRUST WIRELESS POWER SYSTEM 310SY
4
5 Technical specifications
Description: Answer:
Wireless technology RF / 433 MHz
Max. capacity [Watts] 400
Number of channels 16 home code (A - P); 16 device
code (1 –16) (256 total)
Range [Metres] 30m. unobstructed area
RF approval no. (CE xxxx !) CE 0560 (!)
Chipset remote control PT2262
Number of remote control buttons 1 rotation switch / 1 Slide switch/ 8
push buttons
Number of dimmer buttons 2 rotation switches
Operation frequency [channels 1 / 2/ 3/
4,....]
433.92 MHz +/- 200 kHz
Range (Metres) 30m. unobstructed area
Battery A23, 12V
Product dimensions [HxWxL(mm)] 20 x 38 x 97
Product dimensions [HxWxL(mm)] 115 x 55 x 55
Weight (kg) 0.2
6 Troubleshooting
Problem Cause Solution
Other strong frequency
signals (of a wireless
telephone, loudspeakers, for
example) may interfere with
the operation of the
switching system.
Move one of the
interfering transmitters or
move the dimmer.
You are covering the remote
control with your hand too
much.
Make sure the remote
control is not covered by
your hand.
The dimmer responds
poorly.
Transmission range is
obstructed by walls.
Move the dimmer.
The device connected has
its own switch, which is in
the off position.
Make sure the devices
connected are switched
on.
The device connected is
defective.
Check or have checked
whether the device
functions
The dimmer does not
respond.
The device code of your
remote control and the
dimmer are not set to the
same code.
Set the device code for
both devices to the same
number.

TRUST WIRELESS POWER SYSTEM 310SY
5
UK
Problem Cause Solution
A similar system with the
same home codes is being
used in your vicinity.
Change the home codes
of your dimmer and the
other wireless devices in
our system.
The device connected
switches on by itself.
Other strong frequency
signals (of a wireless
telephone, loudspeakers, for
example) may interfere with
the operation of the
switching system.
Move one of the
interfering transmitters or
move the dimmer.
Register your product via www.trust.com so that you are able to receive optimal
guarantee and service support such as up-to-date FAQ. You will be automatically
informed of developments to your product and of other Trust products. You will also
have the chance to win some spectacular prizes.
If you still have any problems after trying these solutions, please contact one of the
Trust Customer Care Centres. You can find more information on the last page of this
electronic manual, as well as at the back of the quick installation manual. Please have
the following information available:
•The article number. This is: 12562;
•A good description of what precisely does not work;
•A good description of when precisely the problem takes place.