Trust START-LINE ACM-2300-HC User manual

USER MANUAL
MULTI LANGUAGE
BUILD-IN SWITCH
Item 71229 Version 1.0
Visit www.trust.com
for the latest instructions
STARTLINE
ACM2300HC

2
1
3
2
4
ACM-2300-HC BUILD-IN SWITCH
5mm
3A
3B
1
3
2
4

3
5
ACM-2300-HC BUILD-IN SWITCH
6c6b
6a
PP
L
N
Wall switch
Wall switch
N N S L
L
P
L
N
Wall switch
N N S L
L
5
L
i
v
e
w
i
r
e
(
b
r
o
w
n
)
N N S LL
L
i
v
e
w
i
r
e
(
b
r
o
w
n
)
0
m
1
m
1
0
m
1
h
4
h
N N S LL
0
m
1
m
1
0
m
1
h
4
h
L
i
v
e
w
i
r
e
(
b
r
o
w
n
)
N
e
u
t
r
a
l
w
i
r
e
(
b
l
u
e
)
S
w
i
t
c
h
w
i
r
e
(
b
l
a
c
k
)

4
ACM-2300-HC BUILD-IN SWITCH
8c8b
8a7
N N S LL
0
m
1
m
1
0
m
1
h
4
h
1 sec
ON
LED
N N S LL
0
m
1
m
1
0
m
1
h
4
h

5
ACM-2300-HC BUILD-IN SWITCH
11
109
N N S LL
0
m
1
m
1
0
m
1
h
4
h
N N S LL
0
m
1
m
1
0
m
1
h
4
h
ON - OFF

6
ACM-2300-HC BUILD-IN SWITCH
N N S LL
0
m
1
m
1
0
m
1
h
4
h
N N S LL
0
m
1
m
1
0
m
1
h
4
h
A B C
A B C
1 sec
OFF
N N S LL
0
m
1
m
1
0
m
1
h
4
h
LED
N N S LL
0
m
1
m
1
0
m
1
h
4
h
8 sec Shortly
N N S LL
0
m
1
m
1
0
m
1
h
4
h
LED

7
ACM-2300-HC BUILD-IN SWITCH

8
EN ACM-2300-HC BUILD-IN SWITCH
1. Disable mains power
Always turn OFF the mains power (In the fuse box) before you begin the installation or removal of
this product. The ACM-2300-HC can be used for either two wall switches connected with one lamp
(stairwell/hotel circuit) or for one single wall switch connected to one lamp.
2. Loosen ceiling lights
Remove the existing lighting from the ceiling, leaving the wires connected to the lighting.
Lighting may not exceed the maximum wattage. If there is no live wire (brown) present, it must be
installed. Wire colors may vary per country. Consult an electrician if in doubt about wire colours.
3. Warning for stripping wires
3A. Make sure the wires are stripped for 5mm.
3B. When connecting the wires to the ACM-2300-HC make sure the stripped wires are pressed firmly
in the module, no exposed wires are visible and the wires cannot touch each other. This can cause
a short circuit.
4. Disconnect the switch wire and neutral wire
To install the ACM-2300-HC disconnect the switch wire (black) and neutral wire (blue) of the lamp
(Disconnect from terminal block or cut the wires if necessary)
5. Connect the live wire to a terminal block
Connect the live wire (brown) from the ceiling box to a terminal block. Connect the other end of the
live wire (brown) also back into the same terminal block.
6A. Connect the wires to the module
• Connect the neutral wire (blue) from the ceiling box to the outer [N] contact of the module
• Connect the switch wire (black) from the ceiling box to the [S] contact.
• Connect the neutral wire (blue) from the lamp to the middle [N] contact.
• Connect the switch wire (black) from the lamp to the [ L] contact.
• Connect one new live wire (brown) from the live wire (brown) terminal block to the [L] contact.
• Tighten the terminal screws firmly.

9
EN
ACM-2300-HC BUILD-IN SWITCH
6B. This is the technical installation schematic of the ACM-2300-HC with two wall-switches (hotel/
stairwell circuit).
6C. This is the technical installation schematic of the ACM-2300-HC with one wall-switch.
7. Enable mains power
Switch the mains power ON before proceeding with the installation.
Make sure no stripped parts of wires are touched after this step.
The LED indicator on the receiver will light up for a few seconds when voltage is applied.
8A. Activate pairing mode
Press for about 1 second (with a pointed object) on the Connect button to activate the pairing mode.
The pairing mode will be active for 12 seconds and the LED indicator on the receiver will flash slowly.
8B. Send an ON signal
While the LED indicator flashes, press the ON button on a Trust Smart Home transmitter to pair the
transmitter to the ACM-2300-HC. (Or activate a Trust Smart Home sensor).
8C. Pairing confirmation
The LED on the module will blink fast in order to confirm that the code is stored. The receiver can
store up to 32 dierent transmitter codes in its memory. The memory is retained when the receiver is
installed elsewhere or when there is a power failure.
9. Wireless control
Send with the transmitter an ON signal to turn the light on wirelessly.
Send with the transmitter an OFF signal to turn the light o wirelessly.
The existing wall switches which are used to control the connected lighting can still be used.

10
EN
ACM-2300-HC BUILD-IN SWITCH
10. Set the desired switch-o time
Set the switch-o time to the desired position with a flathead screwdriver. The switch-o time can
also be changed after the switch is paired to a Trust Smart Home transmitter.
0m: No OFF signal is sent automatically.
1m, 10m, 1h and 4h: An OFF signal is automatically sent after 1 minute, 10 minutes, 1 hour or 4 hours.
11. Placing the receiver
Place the receiver in the ceiling box. Mount the lights back in place.
Make sure that you can always reach the receiver, for example, to reset it, or to register a new
transmitter.
Make sure no stripped parts of wires touch each other.
Deleting a single transmitter code
APress for about 1 second on the Connect button. The pairing mode will be active for 12 seconds and
the LED indicator on the receiver will flash slowly.
BSend while the pairing mode is active with the connected Trust Smart Home transmitter an
OFF signal. If necessary, consult the instruction manual of the transmitter.
CThe LED on the module will flash to confirm that the code has been removed.
Repeat this procedure to delete several transmitters from the receiver.
Erase entire memory
APress the Connect button for about 8 seconds until the LED indicator flashes quickly.
BWhen the LED indicator flashes rapidly, press the Connect button again shortly to confirm that you
want to completely erase the memory.
CThe LED on the module flashes to confirm that the memory has been erased.