Tudelu Closure User manual

1
Installation Manual
SYSTEM:
Closure

2

3
TABLE OF CONTENTS
PRE-INSTALLATION CHECKLIST
BOXES CHECKLIST 4
TOOLS CHECKLIST 5
HOUSING UNIT:
INSIDE THE BOX 6
INSTALLATION 7
LASER CHECK 8
TUBE UNIT:
INSIDE THE BOX 9
INSTALLATION 10
REMOTE CONNECTION 11
WALL PANEL:
INSIDE THE BOX 12
INSTALLATION 14
SIDE GUIDE:
INSIDE THE BOX 16
INSTALLATION 17
BOTTOM HOUSING COVER 18
MOTOR LIMITS 19

4
Before getting started,
A. make sure you received each of the following boxes.
Housing Unit
Wall Panel
Tube and Bottom Bar
Side Guide
BOXES CHECKLIST
Boxes Checklist

5
TOOLS CHECKLIST
Tools Checklist
These are the tools you'll need to install your system.
Extension cord
Tape measure
Drill
Revit Gun Flat screwdriver
Ladder
laser
Stapler
Saw
With Aluminum Blade
Drill Bits
Leveler
Material ifter

6
HOUSING UNIT: INSIDE THE BOX
Motor bracket
Idler bracket
Unit connector Housing cover
Housing
(amount of units depends on the
legth of your specific system)
Housing unit: inside the box

7
END RESULT
Lift up one housing unit Lift motor bracket and side up to
end of housing unit
NOTE: start with the side closest to the room power
INSTRUCTIONS
Insert screws to top of motor
bracket and tighten into ciling
Insert unit connector in between
units
Repeat with second housing and
idler bracket
Insert screws on either side of unit
connector and tighten very well
HOUSING UNIT: INSTALLATION
Housing unit: installation

8
Use the laser to ensure the housing units is leveled
Double check both sides using a laser and a tape measurer
NOTE: it is extremely importan that all housing units are the same exact height.
Make sure there is no space between housing units
HOUSING UNIT: LASER CHECK
Housing unit: laser check

9
TUBE UNIT: INSIDE THE BOX
Motor End
Idler end
Kedar side
Tube unit: inside the box

10
Use material lift to raise tube housing system
INSTRUCTIONS
Insert motor end of tube into the
motor bracket
Insert pin to secure the tube
NOTE: make sure the wire is not
stuck in the pin
Insert idler end of tube into the idler
bracket
Secure the wire by sliding the
motor end of the tube all the way
into the motor bracket
NOTE: if you want the wire to hang or the side of the housing, bringin to the side now
, otherwise leave the wire in the back
Connect wire to the rooms
electricity
Insert pin to secure the tube
TUBE: INSTALLATION
Tube: installation

11
INSTRUCTIONS
hold the remote facing housing units
Use up and down buttons to bring keder side of tube to the bottom (facing the
floor)
Turn remote around and use a
screwdriver to press reset button for 6
seconds
(motor will begin moving up and down)
REMOTE CONNECTION
Remote connection

12
WALL PANEL: INSIDE THE BOX
large panel
small panel
Wall panel: inside the box

13
INSTRUCTION
Raise small panel to housing unit Slide small panel into keder side to
tube
NOTE: zipper must be hanging down
Put material (On brown paper) on
the floor and place large panel on
top
NOTE: before lifting panel you are going to insert bottom bar , (see next page)
roll out wall panel and place roller
on the keder side
WALL PANEL: INSIDE THE BOX
END RESULT
Wall panel: inside the box

14
Slide bottom bar into keder side of
large panel
Push end covers onto either sides
of the bottom bar
Insert screws to connect end cover
to bottom bar make sure keder is in between
end covers and screw end covers
together
WALL PANEL: INSTALLATION
4 end corners Screws
Bottom bar
INSTRUCTION
Wall panel: installation

15
Roll large panel with bottom bar
side facing in
Roll large panel with bottom bar
side facing in
Use material lift to raise large panel
to small panel (zipper facing up)
Staple the beginning to secure
connection
Lower large wall panel to make
sure it's the right height
Start zipping large panel to small
panel
Zip all the way and staple the end
WALL PANEL: INSTALLATION
Wall panel: installation

16
SIDE GUIDE: INSIDE THE BOX
Track holder
inside
Screws
Side Guide
Side guide: inside the box

17
Use tape measurer to measure exact height from floor to bracket (which is
inside the end of the housing)
Remove track holders from side
guides
Use metal on the side guide to
detect where the magnets are
NOTE: this is extremely important!
Use saw to cut side guides to
correct size - Make sure to avoid
magnets
Use saw to cut track holders -
keeping them 2'' longer than the
side guides
SIDE GUIDE: INSTALLATION
INSTRUCTION
Side guide: installation

18
Insert screws into side guide and
screw into wall
side track holder into side guides
horizontally
Use screw driver to prop track
holders up
Insert housing cover
Lift side guides against either side
of wall
Insert side of wall panels into track
holders
Use Rivet Gun to connect the
housing cover
Make sure side guides are leveled
and perfectly aligned with walls
SIDE GUIDE: INSTALLATION
BOTTOM HOUSING COVER
Side guide: installation

19
Hold stop button for 5 seconds Use up button to Lower wall panel
until desired height limit
Hold stop button for 5 seconds
Use a screwdriver to press reset
button for 6 seconds Use up button to raise wall panel
until desired height limit
MOTOR LIMITS
Motor limits

20
End
CONGRATULATIONS ON YOUR MASTERPIECE!
View with partition raised
View with partition lowered