Tudelu MUTE User manual

1
Installation Manual
SYSTEM:
MUTE

2
TABLE OF CONTENTS
MEET THE SYSTEM 3
PRE-INSTALLATION CHECKLIST: 4
- BOXES 5
- TOOLS 6
- ROOM 7
HOUSING INSTALLATION:
- INSIDE THE BOX:
- BEGINNING UNIT 9
- MIDDLE UNIT 10
- END UNIT 11
- ASSEMBLY 12
- INSTALLATION 14
- SOUND BOARDS 17
- ROLLERS 18
- MOTOR:
- INSIDE THE BOX 19
- TUBE:
- ASSEMBLY 20
- INSTALLATION 22
WALL PANEL UNIT:
- INSIDE THE BOX 23
- INSTALLATION 24
WEIGHT & BOTTOM BAR UNIT:
- INSIDE THE BOX 26
- INSTALLATION 27
UNDER HOUSING COVER:
- INSIDE THE BOX 29
- INSTALLATION 30
SIDE GUIDE:
- INSIDE THE BOX 32
- ASSEMBLY 33
- INSTALLATION 37
CONTROL BOX:
- INSTALLATION 39
TABLE OF CONTENTS

3
MEET THE SYSTEM
WEIGHT &
BOTTOM BAR
SIDE GUIDE
WALL
PANEL
HOUSING
MEET THE SYSTEM

4
Boxes checklist
Tools checklist
Room checklist
1.
2.
3.
Before getting started, complete the following
checklists to ensure you are set for installation:
PRE-INSTALLATION CHECKLIST
PRE-INSTALLATION CHECKLIST

5
CHECKLIST #1 : BOXES
Make sure you received your full order.
*amount depends on the length of your specific system
Beginning Unit
Ending Unit
Wall Panel Units* 2 Side Guide UnitsWeight and
Bottom Bar Unit
Middle Unit/s*
Motor Unit
CHECKLIST #1 : BOXES

6
These are the tools you'll need to install your system:
Extension cord
Tape measure
Drill
Flat screwdriver
Wrenchs Philips #2
Socket / Wrench;
7/16 +
3/8 +
9/16
Utillty knife
Laser
2 ladders and
scaolding
Stapler
Saw
with aluminum blade
Plier
Drill bits
Leveler
Material Lift
Duct tape
CHECKLIST #2 : TOOLS
CHECKLIST #2 : TOOLS

7
CHECKLIST #3 : ROOM
A. Make sure you have power to operate your tools and the system
B. Ensure the power is in a convenient location
C. Clear the room for installation
D. Use the laser to check that the structural support is leveled
E. Mark both sides of the wall
this is where the side tracks will go
CHECKLIST #3 : ROOM

8
CHECKLIST #3 : ROOM
F. Verify once more that the system you ordered and the room
measurements match
G. Mark 26'' on the ceiling
(this is where the system will be installed)
H. If installed on a drop, ensure that each nut and bolt is firmly
tightened
CHECKLIST #3 : ROOM

9
BEGINNING UNIT - HM1066
Beginning housing
frame
3 sets of:
4 large rollers
2 small rollers
2 tubes
HOUSING INSTALLATION : INSIDE THE BOX
Soundboards
Under-housing covers
and access panels
Screws and tools
HOUSING INSTALLATION : INSIDE THE BOX

10
MIDDLE UNIT - HM1060
Middle housing frame
3 sets of:
4 large rollers
2 small rollers
2 tubes
Each Middle Unit box contains:
HOUSING INSTALLATION : INSIDE THE BOX
Soundboards
Under-housing covers
Screws and tools
HOUSING INSTALLATION : INSIDE THE BOX

11
ENDING UNIT - HM1089
Ending housing frame
3 sets of:
4 large rollers
2 small rollers
2 tubes
HOUSING INSTALLATION : INSIDE THE BOX
Soundboards
Under-housing covers
and access panels
Screws and tools
HOUSING INSTALLATION : INSIDE THE BOX

12
Place metal rods under the housing so the unit remains intact
when you lift it
Set all the housing modules on the floor before installation
HOUSING INSTALLATION : ASSEMBLY
HOUSING INSTALLATION : ASSEMBLY

13
Follow the instructions that are relevant to your system and refer
to the mini manual for more information
Insert the screw clamp and washers
into the unistrut
When connecting the unistrut to the
housing, make sure the clamp screw
is inside to ensure that it locks within
Disconnect the screws from the
housing
Connect all 6 screws
Connect the unistrut to the housing
Note: Do not tighten the screw,
You will need space for leveling
Insert the screws and washers into
the housing
DIRECT TO I-BEAM CROSS/DROP SECTION
HOUSING INSTALLATION : ASSEMBLY
HOUSING INSTALLATION : ASSEMBLY

14
Use the material lift to raise the first housing unit
Push the screw clamp in Push the screw in and rotate
Note: Do not tighten the screw all
the way
Tighten the screw
HOUSING INSTALLATION : INSTALLATION
DIRECT TO I-BEAM CROSS/DROP SECTION
HOUSING INSTALLATION : INSTALLATION

15
Repeat the previous steps to install the middle housing frame/s
Repeat the previous steps to install the ending housing frame
HOUSING INSTALLATION : INSTALLATION
HOUSING INSTALLATION : INSTALLATION

16
Project a laser beam across the housing. If it isn't leveled, use
the laser's lowest point as a guide to level the housing
Check all 4 corners of each housing
to ensure they are all leveled
If nedded insert a shim to lower the
housing
Join each housing unit together
Tighten the screws that connect the
housing to the unistrut
Use laser again to ensure all the
housing is leveled
HOUSING INSTALLATION : INSTALLATION
HOUSING INSTALLATION : INSTALLATION

17
Lock the fingers
Open the fingers
Repeat for all the soundboards
Insert the boards
Finger
HOUSING INSTALLATION : SOUNDBOARDS
END RESULT
HOUSING INSTALLATION : SOUNDBOARDS
INSTRUCTIONS

18
Repeat on the other side
All rollers should be facing the same
way
Note: Only one side could be pushed in
Insert the rollers into the arms
1. Larger rollers go on either side
2. Smaller rollers go in the center
Arm
HOUSING INSTALLATION : ROLLERS
END RESULT
HOUSING INSTALLATION : ROLLERS
INSTRUCTIONS

19
MOTOR UNIT - HM1138
2 motors
2 idlers
MOTOR UNIT : INSIDE THE BOX
2 control boxes
MOTOR UNIT : INSIDE THE BOX

20
Push the tube connector halfway to
secure
Connect the motor to the starter tube
Note: The screws connecting the motor are dierent
than the screws connecting the tubes to the connectors
TUBE PART BREAKDOWN
Connect the starter tube to the tube
connector
Repeat until all the tubes are
connected
Connect the middle tube to the other
end of the tube connector
Insert the idler to secure the system
Starter tube
(Notice the screws for the motor)
Middle tube
Ending tube
Tube
connectors
HOUSING INSTALLATION : TUBE ASSEMBLY
INSTRUCTIONS
HOUSING INSTALLATION : TUBE ASSEMBLY