Turn of the century 20564 User manual

9151 • 120715
CEILING FAN
LIGHT KIT
Owner’s Manual
Models #20564
Turn of the CenturyTM
If a problem cannot be remedied or you are experiencing diculty in installation,
please contact the Service Department: 1-877-459-3267, 9 a.m.- 5 p.m. Central time.

TM
Turn of the Century
PACKAGE CONTENTS
2
HARDWARE CONTENTS
MOUNTING OPTIONS
1. Canopy
2. Downrod
3. Hex Nut
4. Lock Washer
5. Light Kit Fitter
6. Bulbs (x 3)
7. Light Cage (x 3)
8. Hardware Kit
9. Owner’s Manual
Unpack your light kit and check the contents. You should
have the following items:
PACKAGE CONTENTS
HARDWARE LIST
Note: Some of the hardware listed is pre-assembled to
other parts. You will be instructed where to locate it.
Ceiling Fan Light Kit Ceiling Light Fixture
10 18
13
11 12 14 15 16
17
10. Wire Connector (x 2)
11. Hex Nut
12. Lock Washer
13. IP Rod
14. Coupling
15. Mounting Bracket
16. Cap Nut (x 2)
17. Bracket Screw (x 2)
18. Pull Chain Extension
Hardware Kit
Owner’s
Manual
1
2
5
3 4
67
8
9

TM
Turn of the Century
WARNING
READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE BEGINNING TO INSTALL THE LIGHT
KIT AND SAVE INSTRUCTIONS.
• This xture is intended for use with an indoor ceiling fan. Not suitable for damp or outdoor locations.
• The fan images and instructions in this manual are generic, but in most cases the installation will be easy to
follow. If unsure about installation, consult a qualied licensed electrician for proper installation.
• To avoid risk of electric shock, be sure to shut o power at the main fuse or circuit breaker box before
installing or servicing this xture. Turning o the electrical power by using the light switch is not sucient to
prevent electrical shock.
• Installation must comply with the national electrical code, ANSI/NFPA 70-1999 and local codes. If you
are unfamiliar with the methods of installing electrical wiring, seek the services of a qualied licensed
electrician.
• To avoid personal injury, the use of gloves or protective clothing may be necessary when handling xture
parts with sharp edges.
• To reduce the risk of re, electrical shock or personal injury, do not connect this xture to a ceiling fan is not
properly grounded.
• To reduce the risk of re, electrical shock, or personal injury, each wire connector used with this light kit
should accept only one 18-gauge wire from the light kit and one 18-gauge wire from the ceiling fan.
• When mounting xture to a ceiling fan, ensure the fan is mounted to an outlet box labelled “Acceptable for
fan support” and is secured to the building structure.
• Wire colors from ceiling fan may not be the same color used in this manual. When in doubt, consult a
qualied licensed electrician to determine the proper wiring.
SAFETY INSTRUCTIONS
NOTE: The net weight of the light kit is less than: 4.4 lbs.
3

Turn of the CenturyTM
4
ASSEMBLY INSTRUCTIONS - FAN MOUNT
2
1
1. Turn OFF the electrical power at the main fuse or circuit
breaker.
3. Remove the three switch housing screws in order to
remove the switch housing (A) or switch housing cap
(B) from the existing fan. If applicable, remove any wire
connectors that connect wires from the fan to the switch
housing and/or disconnect the male and female plugs.
Note: Save the three switch housing screws for later.
2. Select the conguration (A or B) which most closely
matches your fan. Most ceiling fans have either a
one-piece removable switch housing that connects to
a tter plate (A) or a permanent switch housing with a
switch housing cap (B).
4
4. Use a screwdriver to push the plug button out of the
switch housing (A) or switch housing cap (B).
Switch Housing
Switch Housing
Switch Housing
Switch Housing
Plug Button
Plug Button
Switch Housing Cap
Switch Housing Cap
Switch Housing Cap
Switch Housing Screw
Switch Housing Screw
Fitter Plate
3
A
A
A
B
B
B
For ceiling mount, skip to page 7.

5Turn of the CenturyTM
ASSEMBLY INSTRUCTIONS - FAN MOUNT
6
5
6. Remove the hex nut and lock washer from the threaded
rod at the top of the light kit tter. Then, insert the wires
and threaded rod from the light kit tter through the
center hole in the switch housing (A) or the switch housing
cap (B). Secure the switch housing (A) or switch housing
cap (B) to the light kit tter using the lock washer and hex
nut from the hardware bag.
5. Remove the four cage screws from the brackets inside
the shade. Install the bulb in the socket. Then attach
the light cage to the shade using the four cage screws.
Repeat for each shade.
7. Use the wire connectors to connect the wires from the
light kit tter to the wires in the switch housing (A or B).
If your fan has a tter plate (A), you may also need to
connect the 9-pin connector from the fan to the 9-pin
connector from the switch housing.
Note: If your fan has two single-pin connectors instead of
bare wires, it will be necessary to cut the wire very close to
the single-pin connectors and strip 1/2” of insulation from
the end of the two wires in order to connect the fan wires
to the wires of the light kit. IMPORTANT: DO NOT cut the
wires to the 9-pin connectors.
Lock
Washer
Light Cage
Bracket
Bulb
Cage Screw
Shade
Lock
Washer
Hex Nut
9-pin
Connector
White to White
White to White
Black to Blue
Black to Black
Hex Nut
8. Using the three previously removed switch housing
screws, re-attach the switch housing to the tter plate (A)
or the switch housing cap to the switch housing (B).
7
8
A
A
A
B
B
B
Switch
Housing Screw
Switch
Housing Screw

6Turn of the CenturyTM
ASSEMBLY INSTRUCTIONS - FAN MOUNT
9. Attach the pull chain extensions to the pull chains.
9
10
Pull Chain Extension
10. Restore the power at the main fuse or circuit breaker.

7Turn of the CenturyTM
1
3
4
ASSEMBLY INSTRUCTIONS - CEILING MOUNT
1. Turn OFF the electrical power at the main fuse or circuit
breaker.
2. Remove the four cage screws from the small brackets
inside the shade. Install the bulb in the socket. Then
attach the light cage to the shade using the four cage
screws. Repeat for each shade.
2
Light Cage
Bulb
Cage Screw
Shade
3. Remove the hex nut and lock washer from the IP rod.
Then, feed the wires through the coupling and IP rod.
Then, screw the coupling onto the threaded rod on top of
the light kit tter.
IP Rod
Coupling
Downrod
Canopy
Hex Nut
Lock Washer
4. Feed the wires through the downrod and canopy.
Secure the downrod and canopy to the IP rod by
reinstalling the lock washer and hex nut.

OUTLET BOX
8Turn of the CenturyTM
6
7
ASSEMBLY INSTRUCTIONS - CEILING MOUNT
5. Attach the mounting bracket to the outlet box (not
included) using the screws and washers provided with
the outlet box.
Cap
Nut
Bracket
Screw
Outlet
Box
Mounting
Bracket
5
Cap Nut
Bracket
Screw
Canopy
Pull Chain Extension
8. Restore the power at the main fuse or circuit breaker.
Assembly is complete.
8
7. Attach the pull chain extensions to the pull chains.
6. Remove the two cap nuts from the bracket screws. Lift
the xture until the end bracket screws extend through
the holes in the canopy. Screw the cap nuts onto the
bracket screws to secure the light kit to the outlet box.

TM
Turn of the Century
9
If you have diculty operating your new light kit, or have diculty with installation, please contact Customer
Service : 1-877-459-3267, 9 a.m.- 5 p.m. Central time.
WARNING: Ensure the power is turned o to the ceiling fan and light kit before performing any maintenance.
PROBLEM SUGGESTED REMEDY
Fixture does not light up. 1. Turn on wall switch, and check fuses or circuit breakers.
2. Check wire connections from fan to light kit, located in the switch housing of the
ceiling fan.
3. Lower the canopy on the fan. Ensure the blue fan wire (light power) is connected to
a black (hot/live) household supply wire. Re-install the canopy.
TROUBLESHOOTING
WARRANTY
5-YEAR LIMITED WARRANTY
To obtain service, please contact the Service Department:
1-877-459-3267, 9 a.m.- 5 p.m. Central time.
Model Name: Ceiling Fan Light Kit
Model No: 20564 - Bronze (SKU: 355-3194)
The manufacturer warrants all of its lighting xtures against defects in materials and workmanship
for one (1) year from the date of purchase. If within this period the product is found to be defective,
take a copy of the bill of sale as a proof of purchase and the product in its original carton to the place
of purchase. The manufacturer will, at its option, repair, replace or refund the purchase price to the
consumer. All costs of installation and removal of the xture is the responsibility of the consumer. This
warranty does not cover xtures becoming defective due to misuse, accidental damage or improper
handling and/or installation and specically excludes liability for direct, incidental or consequential
damages. As some states do not allow exclusions of limitations on an implied warranty, the above
exclusion and limitation may not apply. This warranty gives you specic rights and you may also have
other rights which may vary from state to state.