Turn of the century 35072 User manual

ITEM #355-7029
MODEL #35072
CEILING FAN
1
ATTACH YOUR RECEIPT HERE
Serial Number Purchase Date
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-800-554-6504, 8 a.m. - 4:30 p.m, EST, Monday - Friday.

PACKAGE CONTENTS
2
PART DESCRIPTION QUANTITY
A
BHanging Bracket 1
Washer 2
Mounting Screw 2
Down Rod 1
Hair Pin 1
Clevis Pin 1
Canopy 1
Canopy Hole Cover 1
Blade Iron Ring 1
Motor Assembly 1
Blade 5
Silicone Washer 1
Blade Screw 15
Fan Pull 2
Motor Coupling Cover 1
Light Assembly 1
Light Kit Plate 1
Metal Washer 1
Manual Nut 1
Set Screw 2
Shoulder Screw 2
Glass Shade 1
40-Watt Candelabra base bulb 3
Decorative Cap 1
Finial 1
Blade Iron Ring Screw 4
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
A
U
E
BD
KK
KZ
R
G
C
I
HF
L
N
O
P
X
Q
M
J
T
S
V
W
Y

3
Please read and understand this entire manual before attempting to assemble, operate or install the
product. If you have any questions regarding the product, please call customer service at
1-800-554-6504, 8 a.m. - 4:30 p.m., EST.
WARNING:
• Important: When using an existing outlet box, be sure the box is securely attached to the building
structure and can support the full weight of the fan. Failure to do so can result in serious injury or
death.
• Turn off circuit breakers and wall switch to the fan supply wire leads. Warning: Failure to
disconnect power supply prior to installation may result in serious injury or death.
• Do not install fan on a ceiling with a pitch greater than 20°.
• WARNING – To Reduce The Risk Of Fire, Electric Shock, Or Personal Injury, Mount To Outlet Box
Marked 'Acceptable for Fan Support of 15.9 kg (35 lbs) or less' And Use Mounting Screws
Provided With The Outlet Box and/or Support Directly From Building Structure. Most Outlet Boxes
Commonly Used For The Support of LuminairesAre NotAcceptable For Fan SupportAnd May
Need To Be Replaced. Consult A Qualified Electrician If In Doubt."
• Important: Be sure wiring box is properly grounded or that a ground (green) wire is present.
• Make sure the installation site you choose allows a minimum of 7 feet from the floor to the end of
the blades
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and diagram. If any part is missing or damaged, do not attempt to assemble the product.
Contact customer service for replacement parts.
Estimated assembly time: 30 minutes to 1 hour.
Tools Required for Assembly (not included): Phillips screwdriver, flathead screwdriver, wire strippers,
SAFETY INFORMATION
ASSEMBLY INSTRUCTIONS
1. Secure the hanger bracket (A) to the ceiling outlet
box using screws (C) and washers (B) provided with
the outlet box. Important: If attaching the fan to a
sloped ceiling, make sure open end of mounting
bracket is installed facing the roof. Do not install fan
on a ceiling with a pitch greater than 20°.
1
AB
C

ASSEMBLY INSTRUCTIONS
4
2. Remove the hairpin (E) and clevis pin (F) from the downrod support of the motor assembly (J)
and loosen the two set screws (T). Slide the downrod (D) through the canopy (G), canopy hole
cover (H) and motor coupling cover (O). Feed the black and white and blue wires from fan
through the downrod (D). Insert the downrod into fan assembly aligning the holes in the downrod
support and holes in downrod (D). Secure clevis pin (F) with hairpin (E) and tighten setscrews
(T).
2
E
J
T
G
HO
D
F

ASSEMBLY INSTRUCTIONSASSEMBLY INSTRUCTIONS
5
EEEUEEEA
EEEUEEED
3. Carefully lift the fan and seat the downrod (D)/hanger
ball assembly on the hanger bracket (A) that was
just attached to the outlet box. Be sure the groove in
the ball is lined up with the tab on the hanger bracket
(A).
3
4 Wiring the fan per wiring diagram and Securely connect wires with wire connectors:
• Connect WHITE fan motor wire to WHITE supply wire.
• Connect BLACK and BLUE fan wires to BLACK supply wire.
• Connect GROUND (GREEN) wires from hanging bracket and the downrod ball to GROUND
(GREEN or BARE COPPER) from house.
4
Black
Black
Blue
White White
Ground
Ground

ASSEMBLY INSTRUCTIONS
6
5
EEEUEEEAEEEUU
5. Loosen the two shoulder screws (U) without fully removing the hanger bracket (A). Assemble
canopy by rotating keyhole slot in canopy over shoulder screws (U) in hanger bracket (A). Tighten
shoulder screws (U). Securely attach and tighten the canopy hole cover over the shoulder screws
(U) in the hanger bracket (A) utilizing the keyhole slot twist-lock feature.
6. Raise blade iron ring (I) to motor
assembly (J) and secure blade iron
screws (Z).
J
IZ
6

ASSEMBLY INSTRUCTIONS
7
7. Attached fan blades (K) to the blade iron ring (I) with
blade screws (M).
8. Installing the light kit plate (Q): Remove one of the
three screws on the motor mounting plate and
loosen the other two. Feed the 4-pin connector
through the center hole of the light kit plate (Q).
Align the keyhole slots in the plate with the assembly
screws, turn the light kit plate clockwise until the
assembly screws are firmly situated in the narrow
ends of the keyhole slots. Replace the third screw
and securely tighten all three screws.
9. Installing the light assembly (P): Remove one of the
three screws on the light kit plate (Q) and loosen the
other two. Connect the 4-pin connector from the
motor assembly (J) and light assembly (P). The two
connectors have keyholes that must be mated
correctly before they can be engaged. Align the
keyhole slots in the light assembly (P) with the
assembly screws, turn the light assembly (P)
clockwise until the assembly screws are firmly
situated in the narrow ends of the keyhole slots.
Replace the previously removed assembly screw
and securely tighten all the screws.
KK
KI
M
7
KK
8
I
Q
9
Q
P
J

ASSEMBLY INSTRUCTIONS
8
10.Insert 3, 40-watt max type B bulbs (W) into the the
sockets on the light assembly (P).
11a. Lift the glass shade (V) up to the light assembly (P) allowing the threaded rod and pull chain to
go through the hole in the bottom of the glass shade (V).
11b. Place the silicone washer (L), metal washer (R) and manual nut (S) onto the threaded rod.
11c. Place the decorative cap (X) and tighten the glass shade (V) with the finial (Y).
10
W
P
11c
11b
11a
V
P
L
S
X
Y
CAUTION: Three 40-watt. candelabra-base
bulbs (W) are provided with fan. If you replace the
bulbs with over 190 watts, the fixture will
automatically turn off. When replacing bulbs,
ensure the bulb wattage is below 190 watts.
R

ASSEMBLY INSTRUCTIONS
9
Note: Wait for fan to stop before reversing the switch.
• In warmer weather, counterclockwise movement of the fan will result in downward airflow
creating a wind chill effect.
• In cooler weather, clockwise movement of the fan will result in upward airflow that can help move
stagnant hot air off the ceiling area.
12.Attach fan pulls (N) onto the chain hanging from the
fan motor.
12
N
13
J
13.Use the fan reversing switch located on the motor assembly (J) to optimize your fan for seasonal
performance. Toggle the switch back and forth to find the disired direction.
Reverse
Switch

CARE AND MAINTENANCE
10
At least twice each year tighten all screws and lower canopy to check mounting bracket screws
and downrod assembly. Clean fan housing with only a soft brush or lint free cloth to avoid
scratching the finish. Clean blades with a lint free cloth. Shut off main power supply before
beginning any maintenance. Do not use water or a damp cloth to clean the ceiling fan.

Printed in China
11
WARRANTY
TURN ON THE CENTURY® 355-7029 WARRANTY
Kichler warrants this fan to be free from defects in workmanship and material present at time of
shipment from the factory for Lifetime limited from the date of purchase. This warranty applies only to
the original purchaser. Kichler agrees to correct such defect at no charge or at our option replace the
ceiling fan with a comparable or superior mode.
To obtain warranty service, present a copy of your sales receipt as proof of purchase. All cost of
removal and reinstallation are the expressed responsibility of the purchaser. Any damage to the
ceiling fan by accident, misuse or improper installation, or by affixing accessories not produced by
this warranty, are at the purchaser’s own responsibility. Kichler Ceiling Fans assumes no
responsibility whatsoever for fan installation during the Lifetime limited warranty. Any service
performed by an unauthorized person will render the warranty invalid.
Due to varying climatic conditions, this warranty does not cover changes in brass finish, rusting,
pitting, tarnishing, corroding or peeling. Brass finish fans maintain their beauty when protected from
varying weather conditions. Any glass provided with this fan is not covered by the warranty. Any
replacement of defective parts for the ceiling fan must be reported within the first year from the date
of purchase. For the balance of the warranty, call our customer service department for return
authorization and shipping instructions so that we may repair or replace the ceiling fan. Any fan or
parts returned improperly packaged is the sole responsibility of the purchaser. There is no further
expressed warranty. Kichler disclaims any and all implied warranties. The duration of any implied
warranty which cannot be disclaimed is limited to the Lifetime limited period as specified in our
warranty. Kichler shall not be liable for incidental, consequential or special damages arising at or in
connection with product use or performance except as may otherwise be accorded by law. This
warranty gives you specific legal rights and you also have other rights which vary from state to state.
This warranty supersedes all prior warranties.
Note : A small amount of “wobble” is normal and should not be considered a defect.
For questions / comments, technical assistance or repair parts –
Please call toll free at: 1-800-554-6504 (M-F 8am – 4:30pm)
SAVE YOUR RECEIPTS. THIS WARRANTY IS VOID WITHOUT THEM.
Rev. 11-21-13