Turn of the century Midori20337 User manual

9111 • 12/10/14
52” MIDORI
CEILING FAN
Owner’s Manual
Models #20337, 20338
Turn of the CenturyTM
1
If a problem cannot be remedied or you are experiencing diculty in installation,
please contact the Service Department: 1-877-459-3267, 9 a.m.- 5 p.m. Central time.

TM
Turn of the Century
PACKAGE CONTENTS
2
HARDWARE CONTENTS
17
18
19
20 23
22
21 24
25
26
1. Canopy
2. Canopy Cover
3. Mounting Bracket
4. Yoke Cover
5. Motor Housing
6. Fitter Plate
7. Light Kit
8. Glass Bowl
9. Downrod
10. Blade (x 5)
11. Blade Arm (x 5)
12. CFL Bulb (x 2)
13. Hardware Kit
14. Owner’s Manual
15. Remote
16. Receiver
17. Motor Screw (x 10)
18. Mounting Bracket
Screw (x 4)
19. Blade Screw (x 15)
20. Set Screw (x 2)
21. Star Washer (x4)
22. Blade Washer (x 15)
23. Fitter Plate Screw (x 3)
24. Wire Connector (x 3)
25. Downrod Clip
26. Downrod Pin
Unpack your fan and check the contents. You should
have the following items:
PACKAGE CONTENTS
HARDWARE CONTENTS
Note: Some extra hardware has been included. The quantity
listed above is the number required for installation.
7
6
5
4
3
2
1
16
15
8
9
11
14
13
10
Hardware Kit
Owner’s
Manual
12

TM
Turn of the Century
MOUNTING OPTIONS
3
Dual Mount Drawing
Downrod Mount Angled Ceiling Mount (Up to 10 degrees)
A. 13.39 in. B. 10.47 in. C. 12.24 in. D. 5.08 in.
DIMENSION REFERENCE
C
D
B
A
Choose one of the following mounting options:
Downrod Mount is best suited for ceilings 8 ft. or higher. For taller ceilings you may want to use a longer downrod
(not included).
Angled Ceiling Mount is best suited for angled or vaulted ceilings. A longer downrod is sometimes necessary to
ensure proper blade clearance from the ceiling. If using the angle mount, check to ensure the ceiling angle is not
steeper than 10°.

TM
Turn of the Century
WARNING
READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN INSTALLING THE
FAN AND SAVE INSTRUCTIONS.
All set screws of the fan must be checked and retightened where necessary before installation.
To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets, balancing
the blades or cleaning fan. Do not insert foreign objects in between rotating fan blades.
Before changing the fan direction, turn o the fan and wait for the fan blades to stop completely.
If a stationary appliance is not provided with a supply cord and a plug, or with other means for
disconnection from the main supply having a contact separation of at least 3 mm in all poles, that means for
disconnection must be incorporated in the xed wiring in accordance with the wiring rules.
The safeguards provided by these safety instructions and by the separate installation instructions are not
meant to cover all possible conditions and situations that may occur. It must be understood that common
sense, caution and care are factors which can not be built into this product. These factors must be supplied
by the person(s) installing, caring for and operating the fan.
TO AVOID RISK OF ELECTRIC SHOCK, BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT
BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE. TURNING OFF THE ELECTRICAL POWER
BY USING THE LIGHT SWITCH IS NOT SUFFICIENT TO PREVENT ELECTRICAL SHOCK.
TO REDUCE THE RISK OF INJURY, INSTALL THE FAN SO THAT THE BLADES ARE AT LEAST 7 FEET (2.1
METERS) ABOVE THE FLOOR AND AT LEAST 18 INCHES (0.5 METERS) FROM THE TIP OF THE BLADES TO
THE WALL.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR PERSONAL INJURY, MOUNT TO OUTLET BOX
MARKED “ACCEPTABLE FOR FAN SUPPORT” AND USE MOUNTING SCREWS PROVIDED WITH THE OUTLET
BOX.
THE INSTALLATION HAS TO BE IN ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE, ANSI/NFPA
70-1999 AND LOCAL CODES. IF YOU ARE UNFAMILIAR WITH THE METHODS OF INSTALLING ELECTRICAL
WIRING, SEEK THE SERVICES OF A QUALIFIED LICENSED ELECTRICIAN.
SAFETY INSTRUCTIONS
IMPORTANT:
Before you begin installing or using the fan, carefully read the entire manual. If unsure about any part of the
installation, contact a qualied electrician.
Save all instructions.
NOTE: The fan weight is Net Weight: 18.68 lb (8.47 kg), Gross Weight: 21.76 lb (9.87 kg). Be sure the outlet box
(not included) is securely attached to the building structure and is marked “Acceptable For Fan Support”. Failure
to do so can result in serious injury.
4

Turn of the CenturyTM
Downrod
Clip
Set Screw
Yoke
Downrod
Pin
5
ASSEMBLY INSTRUCTIONS
2
1
1. Turn OFF the electrical power at the main fuse or circuit
breaker.
2. Remove the canopy from the mounting bracket by
removing the two mounting bracket screws and from
the round holes in the canopy. Then loosen the other
two mounting bracket screws from the L-shaped slots.
Retain the mounting bracket screws for later. Install the
mounting bracket to the outlet box (not included) using
the screws and washers provided with the outlet box.
Warning: To reduce the risk of re electric shock,
or personal injury, mount to the outlet box marked
“acceptable for fan support” and use the mounting
screws and washers provided with the outlet box.
4
Mounting
Bracket Screw
3
3. Remove the downrod pin and downrod clip from the
downrod. Then, loosen but don’t remove the set screws in
the yoke.
4. Feed the wires coming from the yoke through the yoke
cover, canopy and downrod.
Downrod
Canopy
Yoke Cover
Yoke

6Turn of the CenturyTM
Black (hot/power)
White (neutral)
Bare/Green (ground)
Red White
White
White
Black
Blue
Blue
Green
Green
Antenna
Note:Receiver wires with white
labels connect to wires from fan.
Receiver wires with red labels
connect to wires from outlet box.
Receiver
Downrod
Mounting
Bracket
ASSEMBLY INSTRUCTIONS
8
7
5
6
5. Insert the downrod into the yoke and reinstall the
downrod pin and downrod clip. Securely tighten the two
set screws.
Note: With wiring extending out of the downrod,
measure 8 inches of lead wire and cut the excess wire
with wire cutters (not included). Then strip 1/2” of
insulation from the end of each wire.
6. Lift the downrod into the mounting bracket. Rotate the
downrod until the tab in the mounting bracket is seated in
the slot in the downrod ball.
WARNING: The fan and/or downrod should
not rotate in the mounting bracket if installed
correctly. Failure to align the slot in the downrod ball with
the tab may result in fan falling causing serious injury or
death.
Downrod Pin
Yoke
Downrod
Downrod Clip
Set Screw
Tab
Slot
Downrod
Downrod
Mounting
Bracket
Wire
Connector
7. Place the receiver in the mounting bracket to prepare
for the wiring process.
Note: The receiver will rest directly on top of the downrod.
8. Use wire connectors to connect the receiver and fan
wires to the supply wires from outlet box according to the
wiring diagram and the following instructions:
• Connect the blue wire from receiver to blue (light power)
wire from fan.
• Connect the black wire from receiver to black (fan power)
wire from fan.
• Connect the red wire from receiver to black (hot/power)
supply wire.
• Connect the white wire with red label from receiver to
white (neutral/common) supply wire.
• Connect the white wire with white label from receiver to
white (neutral/common) wire from the fan.
• Connect the green wires from the fan and mounting
bracket to the bare/green (ground) supply wire.
Important: After the connections have been made, the
connected wires should be turned upward and pushed
carefully up into the outlet box. Place the black and white
wire connections on opposite sides of the outlet box.

7Turn of the CenturyTM
Motor
Screw Blade Arm
Motor
Fitter Plate
Blade Screw
Blade Washer
Blade Arm
Blade
ASSEMBLY INSTRUCTIONS
12
11
9. Raise the canopy, ensure the two mounting bracket
screws are aligned with the L-shaped slots in the canopy.
Then turn the canopy counter clockwise until the
mounting bracket screws are completely engaged in
the L-shaped slots. Install the two previously removed
mounting bracket screws and star washers in the round
holes. Securely tighten all four mounting bracket screws.
10. Remove the ten motor screws from the underside
of the motor but save them for installation of the blade
arms in step 12.
10
9
Canopy
Round
Hole
Motor
Motor Screw
Fitter Plate
Mounting
Bracket Screw L-shaped Slot
11. Partially insert three blade screws, along with the
blade washers, through the blade and into the blade arm.
Tighten each blade screw, starting with the one in the
middle. Repeat this step for the remaining blades.
12. Secure the blade arm to the underside of the motor
using motor screws removed in Step 10. Secure each blade
arm to motor before moving to the next.

8Turn of the CenturyTM
ASSEMBLY INSTRUCTIONS
15
13. Loosen all three tter plate screws, but completely
remove the one located across from to the reverse switch.
14. Then, connect the single-pin connectors from the
tter plate to the light kit -- white to white and blue to
black.
Place the keyholes of the light kit over the two loosened
tter plate screws and rotate the light kit clockwise. Re-
install the third tter plate screw and tighten all three
tter plate screws securely.
14
Single-pin
Connectors
Glass
Bowl
Light Kit Fitter Plate Screw
Fitter Plate
Fitter Plate
Screw
Reverse
Switch
Remove
13
15. Install the CFL bulbs into the sockets of the light kit.
Then, lift the glass bowl up to the light kit and turn in a
clockwise direction until it is secure.
16
16. Restore the power at the main fuse or circuit breaker.
Bulb

9Turn of the CenturyTM
OPERATING INSTRUCTIONS
1
1. Use the fan reverse switch, located on the light kit to
optimize your fan for seasonal performance. Note: The
glass bowl must be removed to access the reverse switch.
Using a ceiling fan will allow you to raise your thermostat
setting in summer and lower your thermostat setting in
winter without feeling a dierence in your comfort.
Note: Wait for the fan to stop before moving the reverse
switch.
In warmer weather, push the reverse switch left which
will result in downward airow creating a wind chill eect.
In cooler weather, push the reverse switch right which
will result in upward airow that can help move stagnant,
hot air o the ceiling area.
A
B
C
D
E
3
4
2. Remove the battery cover from the back of the remote
transmitter and insert the 12-volt battery. Replace the
battery cover.
D/CFL Switch: Switch should be set to “CFL” to correspond
with the included CFL bulbs. Flip to “D”, to enable the
dimming function if you change to incandescent bulbs.
IMPORTANT: The dimmer function does NOT work with
CFL bulbs.
3. To operate the fan using remote control, press and
release the following buttons:
A - High fan speed
B - Medium fan speed
C - Low fan speed
D - Turns the fan o. Press and hold this button for 5
seconds to enter Light Delay O mode, which will turn
o light after one minute. The LED on the remote control
will ash four times to conrm mode setting.
E - Turns the light on and o. Press and hold this button
to dim or brighten when using incandescent bulbs.
4. Install wall bracket for remote control (optional) - Use
the two mounting screws to attach the wall bracket to
the wall. Note: A slot on the back of the remote control
allows it to be stored on the wall bracket when not in use.
2
Remote
Battery
Battery
Cover
Remote
Slot
Mounting
Screw
Battery
Compartment
D/CFL Button
Reverse Switch
LED Indicator
Wall Bracket

TM
Turn of the Century
10
If you have diculty operating your new ceiling fan, it may be the result of incorrect assembly, installation or
wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please
check the Troubleshooting section below. If a problem cannot be remedied or you are experiencing diculty in
installation, please contact the Service Department: 1-877-459-3267, 9 a.m.- 5 p.m. Central time.
PROBLEM SUGGESTED REMEDY
1. Fan does not start 1. Check main and branch circuit fuses or circuit breakers.
2. Check power supply wire connections to fan and switch wire connections in
switch housing.
CAUTION: Make sure main power is turned o before entering canopy.
3. Make sure forward/reverse switch pushed completely up or down. Fan will not
operate when switch is in the middle.
4. Make sure that the wall control is turned ON.
1. Make sure all screws in motor housing are snug, but not overtightened.
2. Make sure the screws which attach the blade arm to the motor are tight.
3. Make sure wire connectors in switch housing are not rattling against each other
or against the interior wall of the switch housing.
CAUTION: Make sure main power is turned o before entering switch housing.
4. If using a light kit, be sure the glass shades are nger tight. Check to be sure light
bulb are snug in sockets and not touching glass shade(s). If vibration persists
from glass, remove glass and install a 1/4 in. wide rubber band on glass neck to
act as an insulator. Replace glass and tighten screws against rubber band.
5. Some fan motors are sensitive to signals from Solid State variable speed controls.
DO NOT USE a Solid State variable speed control.
1. Ensure all blades are screwed rmly into blade arms.
2. Ensure all blade arms are tightened securely to motor.
3. Ensure canopy and mounting bracket are tightened securely to outlet box and
outlet box is mounted rmly to ceiling joist.
4. Switch one blade with a blade from the opposite side. Or balance the fan using a
balancing kit.
5. If blade wobble is still noticeable, interchanging two adjacent (side by side)
blades can redistribute the weight and possibly result in smoother operation.
1. Check blue wire from fan to make sure it is connected to hot (black) power
supply wire.
2. Check for loose or disconnected wires in fan switch housing.
3. Check for loose or disconnected wires in light kit.
4. Check for faulty light bulbs.
CAUTION: Make sure main power is turned o before entering switch housing.
1. The fan must be on high and the light must be on for the remote to operate
properly. Pull the fan pull chain and press power button on transmitter. Repeat
up to 4 times.
2. Press and hold the high and low speed buttons on the remote control at the
same time for 5 seconds. The LED indicator will ash 3 times. When syncing is
complete, the fan will start on the low speed with the light (if applicable) o.
3. Replace the transmitter battery with a new 12-volt battery.
2. Fan is noisy
3. Fan wobbles
4. Light does not work:
TROUBLESHOOTING
5. Remote control does
not work:

TM
Turn of the Century
LIMITED LIFETIME WARRANTY
To obtain Service, please contact the Service Department:
1-877-459-3267, 9 a.m.- 5 p.m. central time.
Model Name: 52” Midori Ceiling Fan
Model No: 20337 - Oil Rubbed Bronze (SKU: 355-1058)
20338 - Brushed Nickel (SKU: 355-1059)
The limited lifetime warranty covers this ceiling fan, for residential use by the original purchaser, against
defects in material or workmanship as follows:
If your Turn of the Century Ceiling Fan motor fails at any time during the lifetime of the original purchaser
due to defects in material or workmanship, we will provide a replacement part free of charge.
If your fan motor fails at any time within one year after the original date of sale to the original purchaser
due to defects in material or workmanship, we will provide labor to repair the defect, with the exception
of take down/reinstallation, free of charge. The original purchaser will be responsible for all labor costs
after this one year period.
If no replacement parts are provided for any part of your fan motor that fails at any time during your
lifetime due to defects in material or workmanship, we will refund the original purchase price of your fan.
If your fan blades, pull chain switch, reverse switch, or any accessory, except glass globes and light
bulbs, fails at any time within one year after the original date of purchase due to a defect in material and
workmanship, we will repair or, if we choose, replace the defective blades, switch, or accessory free of
charge, with the exception of take down/reinstallation services.
If the original purchaser ceases to own the fan, this warranty and any implied warranty, including but not
limited to any implied warranty of merchantability or tness for a particular purpose, become void. This
warranty and any implied warranty, including but not limited to any implied warranty of merchantability
or tness for a particular purpose, do not cover glass globes, light bulbs, or nish on any metal portions
of the fan.
This warranty is in lieu of express warranties. The duration of any implied warranty of merchantability or
tness for a particular purpose, with respect to any Turn of Century Ceiling Fan motor, blades, switch,
or accessories, is expressly limited to the period of the express warranty set forth above for such motor,
blades, switch, or accessories.
This warranty excludes defects, malfunctions, or failures of any Turn of Century Fan that are caused by
repairs by persons not authorized by us, use of parts or accessories not authorized by us, mishandling,
improper installation, modications or damage to the fan while in your possession, or unreasonable use,
including failure to provide necessary maintenance.
To obtain service, contact the service department. You will be responsible for all insurance and freight or
other transportation charges to our factory or service center. A copy of sales receipt is required in order
to obtain service. We will return your fan freight prepaid. Your fan should be properly packed to avoid
damage in transit, for we will not be responsible for any such damages.
In no event shall Turn of Century Fan be liable for consequential or incidental damages.
Some states do not allow the exclusion or limitation of consequential or incidental damages, in which
case the above limitation or exclusion may not apply.
This warranty gives you specic legal rights and you may also have other rights which vary from state
to state.
11