Turn of the century Knit User manual

42” Knit Ceiling Fan

Owners Manual

Ventilador de Techo de 106.7cm

Manual del Propietario

SKU 355-7007

LISTED

42” Knit Ceiling Fan

QUESTIONS, PROBLEMS, MISSING PARTS:

Please do not return to retailer: Call 1-800-749-3267 for any missing parts or

questions regarding installation.

Please reference your SKU (355-7007)

or UPC (082392 636609).

Safety Rules..................................1

Unpacking Your Fan.....................2

Installing Your Fan .......................3

Operating Your Fan ......................10

Care of Your Fan...........................11

Troubleshooting ...........................11

Specications ...............................12

Warranty Information ...................13

Table of Contents

UL Model No. EF200M(E)-42

1. To reduce the risk of electric shock, ensure electricity

has been turned off at the circuit breaker or fuse box

before beginning.

2. All wiring must be in accordance with the National

Electrical Code ANSI/NFPA 70-1999 and local electrical

codes. Electrical installation should be performed by a

qualied licensed electrician.

3. WARNING: To reduce the risk of re or electrical shock,

do not use this fan with any solid-state fan speed con-

trol device.

4. CAUTION: To reduce the risk of personal injury, use

only the screws provided with the outlet box.

5. The outlet box and support structure must be securely

mounted and capable of reliably supporting a minimum

of 35 pounds. Use only UL Listed outlet boxes marked

“FOR FAN SUPPORT.”

6. The fan must be mounted with a minimum of 7 feet

clearance from the trailing edge of the blades to the

oor.

7. Do not operate the reverse switch while fan blades are in

motion. Fan must be turned off and blades stopped be-

fore reversing the blade direction.

8. Avoid placing objects in the path of the blades.

9. To avoid personal injury or damage to the fan and

other items, be cautious when working around or

cleaning the fan.

10. Do not use water or detergents when cleaning the fan

or fan blades. A dry dust cloth or lightly dampened cloth

will be suitable for most cleaning.

11. After making electrical connections, spliced conductors

should be turned upward and pushed carefully up into

outlet box. The wires should be spread apart with the

grounded conductor and the equipment-grounding

conductor on one side of the outlet box.

12. Electrical diagrams are for reference only. Light kits

that are not packed with the fan must be UL listed and

marked suitable for use with the model fan you are in-

stalling. Switches must be UL general use switches.

Refer to the instructions packaged with the light kits

and switches for proper assembly. Use 60W MAX.

BULBS, Type B (supplied).

13. All set screws must be checked and tightened where

necessary before installation.

Safety Rules 1.

READ AND SAVE THESE INSTRUCTIONS

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL

INJURY, MOUNT FAN TO OUTLET BOX MARKED “ACCEPTABLE FOR

FAN SUPPORT” WITH THE SCREWS PROVIDED WITH THE OUTLET

BOX. MOST OUTLET BOXES COMMONLY USED FOR THE SUPPORT

OF LIGHTING FIXTURES ARE NOT ACCEPTABLE FOR FAN SUPPORT

AND MAY NEED TO BE REPLACED. CONSULT A QUALIFIED ELECTRI-

CIAN IF IN DOUBT.

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE

BLADE BRACKETS (ALSO REFERRED TO AS “FLANGES”) DURING

ASSEMBLY OR AFTER INSTALLATION. DO NOT INSERT OBJECTS IN

THE PATH OF THE BLADES.

PLEASE REMOVE RUBBER MOTOR STOPS ON THE BOTTOM OF THE

FAN BEFORE INSTALLING BLADES OR TESTING MOTOR.

a. Blade Attachment Hardware

(15 screws, rubber washers

pre-attached to the brackets)

b. Mounting Hardware

(1 Bolt, 1 Clevis Pin, 1 Rubber

Gasket)

c. Electrical Hardware & Balancing Kit

(Blade Balancing Kit, 3 Plastic Wire

Connectors, 1 Pull Chain for the Fan,

1 Pull Chain for the Light Kit, 1 Plastic

Plug for Non-Light Kit Option.)

5. Ball/downrod Assembly

6. Light Kit with Glass Shade

7. Bulbs (2)

8. Decorative Motor Collar Cover

1. Fan Motor Assembly

2. Canopy

3. Blades (5)

4. Blade Bracket Set with Rubber Washers

Pre-installed (5)

2. Unpacking Your Fan

IMPORTANT: THIS PRODUCT AND/OR COMPONENTS ARE COVERED

BY ONE OR MORE OF THE FOLLOWING U.S. PATENTS: 5,947,436;

5,988,580; 5,971,573; 6,010,110; 6,010,306; 6,039,541; 6,046,416 AND OTHER

PATENTS PENDING.

Unpack your fan and check the contents. You should have the following items:

Installing Your Fan 3.

Tools Required

Phillips screw driver, straight slot screw

driver, adjustable wrench, step ladder,

and wire cutters.

Mounting Options

Ifthereisn’tan existing outletbox,thenread

the following instructions. Disconnect the

power by removing fuses or turning off

circuit breakers.

Secure the outlet box directly to the building

structure. Use the appropriate fasteners

and building materials. The outlet box and

its support must be able to fully support the

moving weight of the fan (at least 35 lbs.)

Do not use plastic outlet boxes.

Figures 1, 2, and 3 are examples of differ-

ent ways to mount the outlet box.

Outlet Box

Note: You may need a longer downrod to

maintain proper blade clearance when

installing on a steep, sloped ceiling. The

maximum angle allowable is 30˚. If

the canopy touches the downrod, re-

move the decorative canopy bottom

cover and turn the canopy 180˚ before

attaching the canopy to the mounting

plate.

Outlet Box

To hang your fan where there is an existing

xture but no ceiling joist, you may need an

installation hanger bar as shown in

Figure 4.

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR PERSONAL INJURY, MOUNT

FAN ONLY TO AN OUTLET BOX MARKED

ACCEPTABLE FOR FAN SUPPORT AND

USE THE MOUNTING SCREWS PROVIDED

WITH THE OUTLET BOX. OUTLET BOXES

COMMONLY USED FOR THE SUPPORT OF

LIGHTING FIXTURES MAY NOT BE ACCEPT-

ABLE FOR FAN SUPPORT AND MAY NEED TO

BE REPLACED. CONSULT A QUALIFIED ELEC-

TRICIAN IF IN DOUBT.

Figure 1

Figure 2

Figure 4

Figure 3

Standard Ceiling

Mounting

1. Remove the mounting plate from the

canopy by loosening the four screws

on the top of the canopy. Remove the

two non-slotted screws and loosen the

slotted screws. This will enable you to

remove the mounting plate (Figure 5).

2. Route the wires exiting the top of the

fan motor through the motor collar cov-

er, canopy and then through the ball/

downrod assembly (Figure 6).

3. Loosen, but do not remove, the 2 set

screws on the collar on top of the mo-

tor housing.

4. Align the holes at the bottom of the

downrod with the holes in the collar

on top of the motor housing (Figure

6). Carefully insert the bolt through the

holes in the collar and downrod. Be

careful not to jam the bolt against the

wiring inside the downrod. Insert the

Hanging the Fan

REMEMBER to turn off the power.

Follow the steps below to hang your

fan properly.

NOTE: This ceiling fan is supplied with two

types of hanging assemblies; the standard

ceiling installation using the downrod with

ball and socket mounting, and the “close-

to-ceiling” mounting. The “close-to-ceiling”

mounting is recommended in rooms with

less than 8-foot ceilings or in areas where

additional space is desired from the oor

to the fan blades. When using standard

downrod installation, the distance from the

ceiling to the bottom of the fan blades will be

approximately 10 inches. The “close-to-ceil-

ing” installation reduces the distance from

the ceiling to the bottom of the fan blades to

approximately 6 inches.

Once you have decided which ceiling

installation you will use, proceed with the

following instructions. Where necessary,

each section of the instructions will note the

different procedures to follow for the two

types of installation.

Figure 6

Remove

Loosen but

Do Not Remove

Figure 5

FAILURE TO PROPERLY INSTALL THE CLEVIS

PIN AS NOTED IN STEP 4 AND PROPERLY

TIGHTEN SET SCREWS AS NOTED IN STEP

5 COULD RESULT IN THE FAN LOOSENING

AND POSSIBLY FALLING.

clevis pin and bend to ensure security,

as noted in the circle inset of Figure 6.

5. Tighten the two screws on top of the fan

motor rmly (Figure 6).

Figure 8

Figure 9

“Close-to-Ceiling”

Mounting

1. Remove the mounting plate from the

canopy by loosening the four screws on

the top of the canopy. Remove the two

non-slotted screws and loosen the slotted

screws. This will enable you to remove the

mounting plate (Figure 5).

2. Remove the decorative canopy bottom

cover from the canopy by depressing

the three studs (Figure 7).

3. Remove three of the six screws and lock

washers (every other one) securing the

reinforcing plate to the top of the fan mo-

tor housing (Figure 8).

4. Place the rubber gasket over the

remaining three screws, route the wires

exiting the top of the fan motor

through the ceiling canopy over

Motor

Collar Screw and

Lockwasher

(3 of 6

Screws)

FAILURE TO COMPLETELY TIGHTEN THE

THREE SCREWS IN STEP 6 COULD RESULT IN

THE FAN LOOSENING AND POSSIBLY FALLING.

Figure 7

the collar at the top of the motor

(Figure 9).

5. Align the mounting holes with the holes

in the motor and fasten, using the three

screws and lock-washers removed in

step 3 (Figure 9).

6. Tighten the mounting screws securely.

Installing Fan to

the Outlet Box

1. Pass the 120-volt supply wires through

the center hole in the ceiling mounting

plate as shown in Figure 10.

2. Install the ceiling mounting plate on the

outlet box, by sliding the mounting plate

over the two screws provided with the

outlet box. When using the close-to-

ceiling mounting, it is important that the

mounting plate be level. If necessary,

use leveling washers (not included)

between the mounting plate and the

outlet box. Note that the at side of the

mounting plate is toward the outlet box

(Figure 10).

3. Securely tighten the two mounting

screws.

4. Carefully lift the assembly up to the ceil-

ing mounting plate and hang the fan

on the hook provided by utilizing one

of the holes at the outer rim of the ceil-

ing canopy (Figure 11). If using stan-

dard mounting, seat the hanger ball in

the mounting plate socket. Make sure

the tab on the mounting plate socket

is properly seated in the groove in the

hanger ball (Figure 11).

Figure 11

Figure 10

THE HOOK AS SHOWN IN FIGURE 11 IS ONLY

TO BALANCE THE FAN WHILE ATTACHING

WIRING. FAILURE TO HANG AS SHOWN

IN FIGURE 11 MAY RESULT IN THE HOOK

BREAKING, CAUSING THE FAN TO FALL. THE

HOOK MUST PASS FROM INSIDE TO OUTSIDE

OF THE CANOPY.

WHEN USING THE STANDARD BALL/DOWN-

ROD MOUNTING, THE TAB IN THE RING AT

THE BOTTOM OF THE MOUNTING PLATE MUST

REST IN THE GROOVE OF THE HANGER BALL

FAILURE TO PROPERLY SEAT TAB IN THE

GROOVE COULD CAUSE DAMAGE TO THE

WIRING.

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT USE A SOLID STATE

SPEED CONTROL WITH THIS FAN. IT WILL

PERMANENTLY DAMAGE THE ELECTRONIC

CIRCUITRY.

Making the Electrical

Connections

REMEMBER to disconnect the power. If

you feel you do not have enough electrical

wiring knowledge or experience, have your

fan installed by a licensed electrician.

Follow the steps below to connect the fan

to your household wiring. Use the wire

connecting nuts supplied with your fan.

Secure the connectors with electrical tape.

Make sure there are no loose strands or

connections.

1. Connect the ground conductor of the

120v supply (this may be a bare wire or

a wire with green insulation) to the green

ground lead(s) of the fan (Figure 12).

When using standard ceiling mounting,

there are two green grounding leads;

one from the ceiling mounting plate and

one from the ball/downrod assembly.

When using Close-to-Ceiling mount-

ing, there is only one green ground lead

from the mounting plate since the ball/

downrod assembly is not used.

2. Connect the fan motor white wire to the

supply white (neutral) wire using a wire

nut (Figure 12).

3. Connect the fan motor black wire to the

supply black (hot) wire using a wire nut

(Figure 12).

WHEN MOUNTING THE FAN ON A SLOPED

CEILING, THE STANDARD BALL/DOWNROD

MOUNTING METHOD MUST BE USED. MAKE

SURE THE MOUNTING PLATE SLOTS ARE ON

THE LOWER SIDE BY SLIDING THE MOUNTING

PLATE FROM THE TOP DOWN.

BLUE

BLACK

WHITE

GREEN

BLUE

BLACK WHITE

WHITE

Outlet

Box

SUPPLY CIRCUIT

Green

Grounding

Lead

BLACK

WHITE

Ground

Downrod

ELECTRICAL DIAGRAMS ARE FOR REFER-

ENCE ONLY. OPTIONAL USE OF ANY LIGHT KIT

SHALL BE UL LISTED AND MARKED SUITABLE

FOR USE WITH THIS FAN.

CHECK TO SEE THAT ALL CONNECTIONS ARE

TIGHT, INCLUDING THE GROUND, AND THAT

NO BARE WIRE IS VISIBLE AT THE WIRE NUTS,

EXCEPT FOR THE GROUND WIRE.

Figure 12

4. Connect the blue wire for the light kit to

the black household wire.

5. Turn the wire connections upward,

spreading them apart so the green

(ground) and white wires will be on one

side of the outlet box and the black and

blue wires will be on the other side, and

push into the outlet box.

Finishing the Fan

Installation

STANDARD CEILING MOUNTING

1. Align the locking slots of the ceiling can-

opy with the two screws in the mounting

plate. Push up to engage the slots and

turn clockwise to lock in place. Imme-

diately tighten the two mounting screws

rmly.

2. Install the remaining two mounting

screws into the holes in the canopy and

tighten rmly.

3. You may now proceed to attaching the

fan blades.

CLOSE-TO-CEILING MOUNTING

1. Carefully unhook the fan from the

mounting plate and align the locking

slots of the ceiling canopy with the two

screws in the mounting plate. Push up

to engage the slots and turn clockwise

to lock in place. Immediately tighten the

two mounting screws rmly.

WHEN USING THE STANDARD BALL/

DOWNROD MOUNTING, THE TAB IN THE RING

AT THE BOTTOM OF THE MOUNTING PLATE

MUST REST IN THE GROOVE OF THE HANGER

BALL. FAILURE TO PROPERLY SEAT THE TAB

IN THE GROOVE COULD CAUSE DAMAGE TO

THE WIRING.

2. Install the remaining two mounting

screws into the holes in the canopy and

tighten rmly.

3. You may now proceed to attaching the

fan blades.

LOCKING SLOTS OF THE CEILING CANOPYARE

PROVIDED ONLY AS AN AID TO MOUNTING. DO

NOT LEAVE THE FAN ASSEMBLY UNATTENDED

UNTIL ALL FOUR CANOPY SCREWS ARE

ENGAGED AND FIRMLY TIGHTENED.

PLEASE REMOVE RUBBER MOTOR STOPS

ON THE BOTTOM OF THE FAN BEFORE

INSTALLING BLADES OR TESTING MOTOR.

Light Kit Option

Your fan is supplied with a light kit assembly

and extra plastic plug for non-light option,

allowing you the option of utilizing your fan

with or without the light kit. Once you have

decided which option you will use, proceed

with the corresponding instructions.

Fan with Light Kit

Remember to disconnect the power.

1. Remove the three mounting screws on

the switch cap of the light kit.

2. Connect the wires for the light kit exiting

the bottom of the motor with the wires

from the light kit. See Figure 12.

3. Slide the switch cap up and secure the

switch cap to the switch housing using

the three screws that were removed in

Step 1.

4. Remove the nut and glass shades.

5. Turn the power off, insert the bulbs

(included) into the light kits (Max 60W.

candelabra).

6. Insert the glass shade and secure it with

the nut. The pull chain should come out

from the support bracket.

7. Pull chain for speed selection passes

through the holes of another support

bracket.

Attaching the

Fan Blades

1. Attach blade to blade bracket using the

screws provided as shown in gure 13.

Please note that the rubber washers are

pre-attached to the blade bracket. Insert

a screw into the bracket. Repeat for the

two remaining screws.

2. Tighten each screw securely.

3. Fasten the blade assembly to the motor

by inserting the alignment post into the

slot on the bottom of the motor and tight-

ening the motor screws. Please note

that the motor screws are pre-attached

into the blade bracket (Figure 14).

4. Repeat steps 1-3 for the remaining

blades.

Figure 13

Figure 14

Table of contents

Languages:

Other Turn of the century Fan manuals

Turn of the century

Turn of the century Walnut Grove Ceiling Fan User manual

Turn of the century

Turn of the century 20161 User manual

Turn of the century

Turn of the century 355-3001 User manual

Turn of the century

Turn of the century 20551 User manual

Turn of the century

Turn of the century 20351 User manual

Turn of the century

Turn of the century Elise Owner's manual

Turn of the century

Turn of the century Menards SKU 355-1844 User manual

Turn of the century

Turn of the century 20223 User manual

Turn of the century

Turn of the century 355-6786 User manual

Turn of the century

Turn of the century 355-3001 Instruction manual

Turn of the century

Turn of the century 20200 User manual

Turn of the century

Turn of the century EF200M-52 User manual

Turn of the century

Turn of the century 20501 User manual

Turn of the century

Turn of the century 20554 User manual

Turn of the century

Turn of the century 52in Novella User manual

Turn of the century

Turn of the century LANGNER 20309 User manual

Turn of the century

Turn of the century 20587 User manual

Turn of the century

Turn of the century 20345 User manual

Turn of the century

Turn of the century SKU 355-7529 User manual

Turn of the century

Turn of the century 355-6776 User manual

Turn of the century

Turn of the century 20261 User manual

Turn of the century

Turn of the century 35072 User manual

Turn of the century

Turn of the century Midori20337 User manual

Turn of the century

Turn of the century 20186 User manual

Popular Fan manuals by other brands

Minka Group

Minka Group minkaAire Wave F843 instruction manual

Airflow

Airflow Adroit DV50 instruction manual

Vornado

Vornado 270 Series owner's guide

comfort air

comfort air TH-10D instruction manual

Livoo

Livoo DOM386 instruction manual

Holmes

Holmes BLIZZARD HAOF-90 owner's guide

Taurus

Taurus GRECO 16 ELEGANCE manual

Quorum

Quorum PINNACLE installation instructions

Monte Carlo Fan Company

Monte Carlo Fan Company 3DIR58RBD-V1 Owner's guide and installation manual

Craftmade

Craftmade UH52 installation guide

Jocel

Jocel JVA030658 instruction manual

MIKA

MIKA MFB1211/GR user manual

Harbor Breeze

Harbor Breeze RLG52NWZ5L manual

Allen + Roth

Allen + Roth L1405 instruction manual

ViM

ViM KUBAIR F400 ECOWATT Technical manual

HIDRIA

HIDRIA R10R-56LPS-ES50B-04C10 user guide

BLAUBERG Ventilatoren

BLAUBERG Ventilatoren CENTRO-M 100 L user manual

Triangle Engineering

Triangle Engineering HEAT BUSTER SPL Series owner's manual