Turn of the century 20551 User manual

9143 • 120515
52” SAN LUCAS
CEILING FAN
Owner’s Manual
Models #20551
Turn of the CenturyTM
1
If a problem cannot be remedied or you are experiencing diculty in installation,
please contact the Service Department: 1-877-459-3267, 9 a.m.- 5 p.m. Central time.

TM
Turn of the Century
PACKAGE CONTENTS
2
HARDWARE CONTENTS
19
20
21
22
23
25
24
26
27
28
29
30
1. Canopy
2. Canopy Cover
3. Mounting Bracket
4. Downrod
5. Yoke Cover
6. Motor Assembly
7. Fitter Plate
8. Switch Housing
9. Light Kit
10. Glass Bowl
11. Finial Cap
12. Finial
13. Blade (x 5)
14. Blade Arm (x 5)
15. Bulb (x 2)
16. Pull Chain Extension (x2)
17. Hardware Kit
18. Owner’s Manual
19. Motor Screw (x 10)
20. Mounting Bracket
Screw(x 4)
21. Blade Screw (x 15)
22. Closemount Screw (x 3)
23. Set Screw (x 2)
24. Blade Washer (X 15)
25. Switch Housing Screw (x 3)
26. Plug Button
27. Wire Connector (x 3)
28. Downrod Clip
29. Downrod Pin
30. Blade Isolator
Unpack your fan and check the contents. You should
have the following items:
PACKAGE CONTENTS
HARDWARE CONTENTS
Note: Some extra hardware has been included. The quantity
listed above is the number required for installation.
Hardware Kit
Owner’s
Manual
1
2
3
4
5
6
7
8
9
10
11
13
12
14
15
16
17
18

TM
Turn of the Century
MOUNTING OPTIONS
3
Closemount
Downrod Mount
Angled Ceiling Mount (Up to 16 degrees)
A. 17.98 in. B. 13.25 in. C. 11.91 in. D. 10.56 in. E. 5.08 in.
DIMENSION REFERENCE
E
DC
A
B
Choose one of the following mounting options:
Closemount method is best suited for ceilings lower than 8 feet. It does not utilize the downrod.
Downrod Mount is best suited for ceilings 8 ft. or higher. For taller ceilings you may want to use a longer
downrod (not included).
Angled Ceiling Mount is best suited for angled or vaulted ceilings. A longer downrod is sometimes necessary to
ensure proper blade clearance from the ceiling. If using the angle mount, check to ensure the ceiling angle is not
steeper than 16°.

TM
Turn of the Century
WARNING
READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN INSTALLING THE
FAN AND SAVE INSTRUCTIONS.
All set screws of the fan must be checked and retightened where necessary before installation.
To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets, balancing
the blades or cleaning fan. Do not insert foreign objects in between rotating fan blades.
Before changing the fan direction, turn o the fan and wait for the fan blades to stop completely.
The safeguards provided by these safety instructions and by the separate installation instructions are not
meant to cover all possible conditions and situations that may occur. It must be understood that common
sense, caution and care are factors which can not be built into this product. These factors must be supplied
by the person(s) installing, caring for and operating the fan.
TO AVOID RISK OF ELECTRIC SHOCK, BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT
BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE. TURNING OFF THE ELECTRICAL POWER
BY USING THE LIGHT SWITCH IS NOT SUFFICIENT TO PREVENT ELECTRICAL SHOCK.
TO REDUCE THE RISK OF INJURY, INSTALL THE FAN SO THAT THE BLADES ARE AT LEAST 7 FEET (2.1
METERS) ABOVE THE FLOOR AND AT LEAST 18 INCHES (0.5 METERS) FROM THE TIP OF THE BLADES TO
THE WALL.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR PERSONAL INJURY, MOUNT TO OUTLET BOX
MARKED “ACCEPTABLE FOR FAN SUPPORT” AND USE MOUNTING SCREWS PROVIDED WITH THE OUTLET
BOX.
THE INSTALLATION HAS TO BE IN ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE, ANSI/NFPA
70-1999 AND LOCAL CODES. IF YOU ARE UNFAMILIAR WITH THE METHODS OF INSTALLING ELECTRICAL
WIRING, SEEK THE SERVICES OF A QUALIFIED LICENSED ELECTRICIAN.
SAFETY INSTRUCTIONS
4
IMPORTANT:
Before you begin installing or using the fan, carefully read the entire manual. If unsure about any part of the
installation, contact a qualied electrician.
Save all instructions.
NOTE: The fan weight is Net Weight: 22.7 lb (10.29 kg). Be sure the outlet box (not included) is securely attached
to the building structure and is marked “Acceptable For Fan Support”. Failure to do so can result in serious injury.

Turn of the CenturyTM
5
ASSEMBLY INSTRUCTIONS
1
1. Turn OFF the electrical power at the main fuse or circuit
breaker.
4
Motor Screw Washer
Motor Block
3
4. CLOSEMOUNT INSTALLATION (OPTIONAL)
a. Remove the canopy cover from the bottom of the
canopy.
b. Remove the three Phillips-head closemount screws from
the top of the motor assembly.
c. Align the holes in the bottom of the canopy with the
screw holes in the top of the motor housing. The larger
holes in the canopy will encompass 3 pre-installed screws.
Secure the canopy to the top of the motor assembly by
reinstalling the three Phillips-head closemount screws.
d. Hang the fan on the hook of the mounting bracket to
leave hands free during the wiring process.
Proceed to Step 9.
2
Mounting
Bracket Screw
3. Remove the motor screws, washers and motor blocks
from the underside of the motor assembly. Discard the
motor blocks and washers, but keep the motor screws for
later.
If you wish to use the Downrod Mount (shown on page 3),
proceed to Step 5.
Closemount
Screw
Canopy
Hook
Mounting
Bracket
2. Loosen all four mounting brackets screws, then
completely remove the two mounting bracket screws
from the round holes of canopy. Set screws aside for later
use.
Warning: To reduce the risk of re electric shock,
or personal injury, mount to the outlet box marked
“acceptable for fan support” and use the mounting
screws and washers provided with the outlet box.

6Turn of the CenturyTM
ASSEMBLY INSTRUCTIONS
7
5
6
DOWNROD MOUNT
5. Remove the downrod clip and downrod pin from the
downrod. Then, loosen but do not remove the two set
screws in the yoke of the motor assembly.
6. Feed the wires coming from the yoke through the
yoke cover, canopy and downrod.
7. Insert the downrod into the yoke in the top of the
motor assembly and reinstall the downrod pin and
downrod clip. Then retighten the two set screws.
Downrod Clip
Downrod
Yoke
Set Screw
Canopy
Yoke Cover
Downrod Pin
Yoke
Downrod
Downrod Clip
Yoke
Downrod
Pin
8
8. With wiring extending out of the top of the downrod,
measure 8 inches of lead wire and cut the excess wire with
wire cutters (not included). Then strip 1/2” of insulation
from the end of each wire. Then, lift the downrod into the
mounting bracket. Rotate the downrod until the tab in the
mounting bracket is seated in the slot in the downrod ball.
WARNING: The fan and/or downrod should not rotate in
the mounting bracket if installed correctly. Failure to align
the slot in the downrod ball with the tab may result in fan
falling causing serious injury or death.
Tab
Slot
Downrod
Mounting
Bracket

7Turn of the CenturyTM
ASSEMBLY INSTRUCTIONS
Black (Hot)
Wire Connector
White (Neutral)
Bare/Green (Ground)
Black Blue White Green
11
10 10. Raise the canopy, ensuring the two mounting bracket
screws are aligned with the J-shaped slots in the canopy.
Then turn the canopy clockwise until the mounting
bracket screws are completely engaged in the J-shaped
slots. Install the two previously removed mounting
bracket screws in the round holes. Securely tighten all four
mounting bracket screws.
11. Attach the blades to blade arms using the blade
screws and blade washers from the hardware kit.
9. Use wire connectors to connect the fan wires to the
power supply wires according to the wiring diagram and
the following instructions:
• Connect the white wire from the fan to the white (neutral/
common) supply wire.
• Connect the black and blue wires from the fan to the
black (hot/power) supply wire.
• Connect the green wire from the fan to the bare/green
(ground) supply wire.
Note: If a second hot/power wire is available from the
outlet box, connect it to the blue (light power) fan wire for
separate fan and light switches.
Important: After the connections have been made, the
wires should be turned upward and pushed carefully
up into the outlet box. Place the black and white wire
connections on opposite sides of the outlet box.
9
Canopy
J-shaped Slot
Round
Hole
Blade
Arm
Blade Screw
Blade Washer
Blade
Mounting
Bracket Screw
Blade Arm
Motor Screw
Blade Isolator
Motor Assembly
12
12. Secure the blade arm and blade isolator to the
underneath side of the motor using motor screws
removed in Step 3. Completely secure each blade arm to
motor before moving to the next.
To install the fan without the light kit, skip to step 16.

8Turn of the CenturyTM
ASSEMBLY INSTRUCTIONS
14
13. Remove the three switch housing screws and washers
from the tter plate. Connect the 9-pin connectors from
the fan to the 9-pin connectors from the light kit. Then,
use the switch housing screws and washers to secure the
light kit to the tter plate.
14. Install the bulbs in the sockets of the light kit. Then,
remove the nial and nial cap from the threaded rod at
the bottom of the light kit.
13
Switch
Housing
Screw
Light Kit
9-pin
Connector
Bulb
Socket
15
15. Feed the pull chain through the center hole in the
glass bowl, the nial plate and the nial. Lift the center
hole in the glass bowl over the threaded rod of the light
kit. Then, lift the nial cap up until it is ush with the glass
bowl and secure by screwing the nial onto the threaded
rod.
Skip to Step 18.
Finial
Finial
Finial Cap
Glass Bowl
Finial Cap
16
Switch
Housing
Plug Button
Switch
Housing
Light Kit
Lock Washer Hex Nut
16. NO LIGHT KIT INSTALLATION (OPTIONAL)
To install the fan without the light kit, remove the
preassembled hex nut and lock washer from the threaded
rod inside the switch housing. Disconnect the single-pin
connectors inside the switch housing. Then, remove the
light kit from the switch housing.
Insert the plug button into the center hole of the switch
housing.

9Turn of the CenturyTM
Pull Chain Extension
ASSEMBLY INSTRUCTIONS
19. Restore the power at the main fuse or circuit breaker.
17. NO LIGHT KIT INSTALLATION (CONT’D)
a. Remove the three switch housing screws from the tter
plate. Then, install the switch housing to the tter plate
with the three switch housing screws.
Switch
Housing
Fitter Plate
Switch
Housing
Screw
17
18
19
18. Attach pull chain extension(s) to the pull chain(s).

10 Turn of the CenturyTM
OPERATING INSTRUCTIONS
1
2. Using a ceiling fan will allow you to raise your
thermostat setting in summer and lower your thermostat
setting in winter without feeling a dierence in your
comfort.
Note: Wait for the fan to stop before moving the reverse
switch.
In warmer weather, push the reverse switch left which
will result in downward airow creating a wind chill eect.
In cooler weather, push the reverse switch right, which
will result in upward airow that can help move stagnant,
hot air o the ceiling area.
IMPORTANT: The reverse switch must be set either
completely left or right in order for the fan to function
correctly. If the reverse switch is set in the middle
position, the fan will not operate.
1. The fan pull chain extends from the switch housing. It
has four positions to control fan speed. One pull is HIGH,
two is MEDIUM, three is LOW and four turns the fan OFF.
The light pull chain is located in the center of the nial. It
turns the light ON and OFF.
2
Fan Pull
Chain
Reverse Switch
Light Pull
Chain

TM
Turn of the Century
11
If you have diculty operating your new ceiling fan, it may be the result of incorrect assembly, installation or
wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please
check the Troubleshooting section below. If a problem cannot be remedied or you are experiencing diculty in
installation, please contact the Service Department: 1-877-459-3267, 9 a.m.- 5 p.m. Central time.
PROBLEM SUGGESTED REMEDY
1. Fan does not start 1. Check main and branch circuit fuses or circuit breakers.
2. Check power supply wire connections to fan and switch wire connections in
switch housing.
CAUTION: Make sure main power is turned o.
3. Make sure forward/reverse switch pushed completely up or down. Fan will not
operate when switch is in the middle.
4. Make sure that the wall control is turned ON.
1. Make sure all screws in motor housing are snug, but not overtightened.
2. Make sure the screws which attach the blade arm to the motor are tight.
3. Make sure wire connectors in switch housing are not rattling against each other
or against the interior wall of the switch housing.
CAUTION: Make sure main power is turned o before entering switch housing.
4. Some fan motors are sensitive to signals from Solid State variable speed controls.
DO NOT USE a Solid State variable speed control.
1. Ensure all blades are screwed rmly into blade arms.
2. Ensure all blade arms are tightened securely to motor.
3. Ensure canopy and mounting bracket are tightened securely to outlet box and
outlet box is mounted rmly to ceiling joist.
4. Switch one blade with a blade from the opposite side. Or balance the fan using a
balancing kit.
5. If blade wobble is still noticeable, interchanging two adjacent (side by side)
blades can redistribute the weight and possibly result in smoother operation.
1. Check blue wire from fan to make sure it is connected to hot (black) power
supply wire or to a separate power supply wire from outlet box.
2. Check for loose or disconnected wires in fan switch housing.
3. Check for loose or disconnected wires in light kit.
4. Check for faulty light bulbs.
CAUTION: Make sure main power is turned o before entering switch housing.
1. Make sure the reverse switch is in the down position.
2. Change to higher fan speed by pulling the fan pull chain.
2. Fan is noisy
3. Fan wobbles
4. Light does not work:
5. Weak airow:
TROUBLESHOOTING

TM
Turn of the Century
LIMITED LIFETIME WARRANTY
To obtain Service, please contact the Service Department:
1-877-459-3267, 9 a.m.- 5 p.m. central time.
Model Name: 52” San Lucas Ceiling Fan
Model No: 20551 - White (SKU: 355-7059)
The limited lifetime warranty covers this ceiling fan, for residential use by the original purchaser, against
defects in material or workmanship as follows:
If your Turn of the Century Ceiling Fan motor fails at any time during the lifetime of the original purchaser
due to defects in material or workmanship, we will provide a replacement part free of charge.
If your fan motor fails at any time within one year after the original date of sale to the original purchaser
due to defects in material or workmanship, we will provide labor to repair the defect, with the exception
of take down/reinstallation, free of charge. The original purchaser will be responsible for all labor costs
after this one year period.
If no replacement parts are provided for any part of your fan motor that fails at any time during your
lifetime due to defects in material or workmanship, we will refund the original purchase price of your fan.
If your fan blades, pull chain switch, reverse switch, or any accessory, except glass globes and light
bulbs, fails at any time within one year after the original date of purchase due to a defect in material and
workmanship, we will repair or, if we choose, replace the defective blades, switch, or accessory free of
charge, with the exception of take down/reinstallation services.
If the original purchaser ceases to own the fan, this warranty and any implied warranty, including but not
limited to any implied warranty of merchantability or tness for a particular purpose, become void. This
warranty and any implied warranty, including but not limited to any implied warranty of merchantability
or tness for a particular purpose, do not cover glass globes, light bulbs, or nish on any metal portions
of the fan.
This warranty is in lieu of express warranties. The duration of any implied warranty of merchantability or
tness for a particular purpose, with respect to any Turn of Century Ceiling Fan motor, blades, switch,
or accessories, is expressly limited to the period of the express warranty set forth above for such motor,
blades, switch, or accessories.
This warranty excludes defects, malfunctions, or failures of any Turn of Century Fan that are caused by
repairs by persons not authorized by us, use of parts or accessories not authorized by us, mishandling,
improper installation, modications or damage to the fan while in your possession, or unreasonable use,
including failure to provide necessary maintenance.
To obtain service, contact the service department. You will be responsible for all insurance and freight or
other transportation charges to our factory or service center. A copy of sales receipt is required in order
to obtain service. We will return your fan freight prepaid. Your fan should be properly packed to avoid
damage in transit, for we will not be responsible for any such damages.
In no event shall Turn of Century Fan be liable for consequential or incidental damages.
Some states do not allow the exclusion or limitation of consequential or incidental damages, in which
case the above limitation or exclusion may not apply.
This warranty gives you specic legal rights and you may also have other rights which vary from state
to state.
12