Tusk 5 Point SFI Approved Safety Harness Quick setup guide

Page | 1
.
Recommended Tools:
Metric Socket Set
Metric Wrench Set
INSTALLATION INSTRUCTIONS AND INFORMATION
Congratulations on your purchase of Tusk 5 Point SFI Approved
Safety Harness. This product is made to handle extreme riding conditions.
Please take note of the information and instructions below to get the most
out of your Tusk Product.
For instructional videos, refer to www.rockymountainatvmc.com/videos.
INSTALLATION INSTRUCTIONS AND INFORMATION
Tusk 5 Point SFI Approved Safety Harness
Disclaimer:
Riding o-road can be dangerous and could lead to serious injury or death. No warranty of representaon is
made as to the products ability to protect the user from any injury or death. By purchasing this product, the user
assumes that risk. The acceptance and/or use of this product purchased from Tusk O-Road by the customer hereby
shall release Tusk O-Road from any and all liability pertaining to the use of such product.
Important:
Exisng mounng locaons must be used to mount the seat belt straps. SAE grade 8, Metric grade
10.9 or higher hardware is required for mounng. Be sure to check for sharp corners that could potenally
damage the straps. Improper mounng could cut or damage the straps.
Warning:
Seat belts must be properly worn at all mes while the vehicle is in operaon.
Always inspect belts, mounng points, buckles, and hardware prior to use.
REPLACE any belts that are torn, damaged, or fraying. DO NOT operate machine if harness is
damaged in any way.
Use mild soap and water for cleaning the harness.
SAE Grade 8, Metric 10.9, or higher hardware is required for mounng.

Page | 2
Installaon steps:
1. Start by removing the seat to gain access to the stock seat belt bolts and
mounng. (Some machines may vary)
2. Remove the stock seat belt and make sure to keep the hardware (may
be re-used).
3. Use the stock seat belt mount locaons to mount the lap belts on both
sides of the seat. Some machines may require addional mounng
brackets (sold separately). When mounng the lap belt, make sure the
angle of the bracket is aimed 40-80 degrees from horizontal to ensure
proper funcon. The angle of the bracket should be at the same angle as
the lap belt when in use. *Failure to do so may damage the lap belt*.
4. Wrap the shoulder straps under and back over the harness bar located
behind the seat. The harness bar should be equal to or slightly lower
than shoulder level while the rider is in the seat. Adjust the shoulder
straps to your desired locaon for the shoulder padding (allow the
sternum strap to be at least 4” below the neckline).
5. Refer to the image below for the proper way to wrap the shoulder
straps to the harness bar:
INSTALLATION INSTRUCTIONS AND INFORMATION
INSTALLATION INSTRUCTIONS AND INFORMATION
Tusk 5 Point SFI Approved Safety Harness

Page | 3
6. Mount the sub belt and route the buckle through the seat pass-
through if available.
7. While sing in the seat, latch the lap belt together with the
shoulder straps, sub belt, and lay it at on across your lap. Pull
the slack out of each lap belt while keeping the latch in the
center of your lap unl it is snug.
8. Sit straight up in the seat and pull the slack out of the shoulder
straps. Make sure the sternum strap is at least 4” below your
neckline. If it is not, adjust the height of your shoulder straps
unl the sternum strap is 4” below neckline. Aer this is done,
check the sub belt and make sure it is ght. If it is not ght,
make adjustment in the slack to ensure it is ght.
9. Double-check all mounng and hardware before operang the
machine. Make sure the latch link is locked and secured to the
velcro at all mes while the vehicle is in moon.
Notes:
Check bolts aer every few rides and aer any hard impacts to insure bolts
are ght.
Always adjust the harness before EVERY ride according to the rider and before operang the machine.
INSTALLATION INSTRUCTIONS AND INFORMATION INSTALLATION INSTRUCTIONS AND INFORMATION
INSTALLATION INSTRUCTIONS AND INFORMATION
Tusk 5 Point SFI Approved Safety Harness
INSTALLATION INSTRUCTIONS AND INFORMATION