Tuttnauer Elara11 User manual

Operation and Maintenance
Manual
Pre/Post-vacuum Class B
Table–top Autoclave
Model Elara11
Cat. No. MAN205-0497002EN Rev. H
Tuttnauer Co. Ltd., Har Tuv Industrial zone B P.O.Box 170, Beit Shemesh
9910101, Israel Tel: [phone], Fax: [phone]
Tuttnauer U.S.A. Co, Ltd. 25 Power Drive Hauppauge, NY, 11788, USA.
Tel [phone], Fax: [phone]

Page 1
Table of Contents
Paragraph Page No.
1. GENERAL...............................................................................................................................3
1.1. MANUFACTURER AND US OFFICIAL CORRESPONDENCE INFORMATION..................................................3
1.2. INTENDED USE...........................................................................................................................3
1.3. INTENDED USERS........................................................................................................................3
1.4. INCOMING INSPECTION................................................................................................................3
1.5. WARRANTY ...............................................................................................................................4
1.6. WARRANTY STATEMENT ..............................................................................................................4
1.7. SAFETY INSTRUCTIONS .................................................................................................................5
1.8. GENERAL INFORMATION ..............................................................................................................7
1.9. SAFETY FEATURES .......................................................................................................................7
1.10. OPERATING CONDITIONS ...........................................................................................................10
1.11. OVERALL DIMENSIONS...............................................................................................................11
1.12. FRONT VIEW ...........................................................................................................................12
1.13. REAR VIEW .............................................................................................................................13
1.14. SPECIFICATIONS........................................................................................................................14
1.15. STEAM GENERATOR DATA..........................................................................................................14
1.16. AUTOCLAVE ELECTRICAL DATA ....................................................................................................15
1.17. UTILITIES ................................................................................................................................15
1.18. ENVIRONMENTAL EMISSION INFORMATION ...................................................................................15
1.19. CONSTRUCTION........................................................................................................................15
1.20. STICKERS DESCRIPTION ..............................................................................................................16
1.21. SYMBOLS DESCRIPTION..............................................................................................................17
1.22. WATER QUALITY ......................................................................................................................19
1.23. DIRECTIVES AND STANDARDS ......................................................................................................20
2. CONTROL PANEL...............................................................................................................21
2.1. DESCRIPTION AND FUNCTIONS OF THE FRONT PANEL.......................................................................22
2.2. VISUAL INFORMATION CENTER....................................................................................................22
2.3. THE CONTROL CENTER ..............................................................................................................23
2.4. DATA CENTER..........................................................................................................................24
2.5. DISPLAYED ERROR MESSAGES /SYMBOLS .....................................................................................24
2.6. DISPLAYED OPERATIONAL MESSAGES /SYMBOLS............................................................................25
3. VIEW SCREENS ..................................................................................................................27
3.1. SCREENS SHOWING A SUCCESSFULLY COMPLETED CYCLE....................................................................27
3.2. SCREENS SHOWING ABORTED CYCLES AFTER A COMPLETED STERILIZATION STAGE .................................28
3.3. SCREENS SHOWING A FAILED CYCLE BEFORE COMPLETING THE STERILIZATION STAGE:...........................29
4. STERILIZATION PROGRAMS ...........................................................................................32
4.1. PROGRAM 1: UNWRAPPED INSTRUMENTS.....................................................................................34
4.2. PROGRAM 2: WRAPPED INSTRUMENTS ........................................................................................35
4.3. PROGRAM 3: UNWRAPPED DELICATE INSTRUMENTS .......................................................................36
4.4. PROGRAM 4: WRAPPED DELICATE INSTRUMENTS ...........................................................................37
4.5. PROGRAM 5: CALIBRATION CYCLE................................................................................................38
4.6. PROGRAM 6: EXTRA DRYING TIME ..............................................................................................39
4.7. PROGRAM 7: VACUUM TEST ......................................................................................................40
4.8. PROGRAM 8: BOWIE AND DICK...................................................................................................41
5. CHECKING AND CHANGING PARAMETERS AND OTHER DATA..............................42
5.1. QUICK OPTIONS DIRECTORY .......................................................................................................43
5.2. MAIN MENU ...........................................................................................................................51

Page 2
5.3. CYCLE PARAMETERS FOR CUSTOM PROGRAMS ...............................................................................60
6. PRINTER...............................................................................................................................69
6.1. PRINTER OUTPUT .....................................................................................................................69
6.2. PRINTER HANDLING ..................................................................................................................71
7. INSTALLATION INSTRUCTION.........................................................................................74
7.1. LIFTING AND CARRYING .............................................................................................................74
7.2. UNPACKING THE AUTOCLAVE ......................................................................................................74
7.3. PLACING .................................................................................................................................74
7.4. ELECTRICAL .............................................................................................................................75
7.5. SETUP ....................................................................................................................................76
7.6. FILLING THE MINERAL-FREE WATER RESERVOIR.............................................................................77
8. PREPARATION BEFORE STERILIZATION .....................................................................79
9. OPERATING INSTRUCTIONS ...........................................................................................83
9.1. PRE-HEATING ..........................................................................................................................83
9.2. WASTEWATER RESERVOIR..........................................................................................................84
9.3. OPENING THE DOOR .................................................................................................................84
9.4. ADDING ADDITIONAL DRYING TIME...............................................................................................85
9.5. LOADING ................................................................................................................................85
9.6. CYCLE DESCRIPTION ..................................................................................................................87
9.7. EXTRA DRYING TIME .................................................................................................................88
9.8. UNLOADING ............................................................................................................................88
10. PREVENTIVE AND SCHEDULED MAINTENANCE....................................................90
10.1. DAILY BY THE OPERATOR............................................................................................................90
10.2. WEEKLY BY THE OPERATOR ........................................................................................................91
10.3. PERIODICALLY BY THE OPERATOR ................................................................................................92
10.4. DRAINING THE RESERVOIR..........................................................................................................92
10.5. REPLACING THE AIR FILTER.........................................................................................................93
10.6. REPLACING THE DOOR GASKET....................................................................................................95
10.7. CHECKING THE SAFETY VALVE .....................................................................................................97
10.8. CLEANING WATER STRAINER .......................................................................................................99
10.9. EMERGENCY OPENING OF THE DOOR...........................................................................................100
11. TROUBLESHOOTING ..................................................................................................101
12. SPARE PARTS LIST.....................................................................................................106
13. ACCESSORIES .............................................................................................................106

Page 3
1. GENERAL
Read the Operating Instructions carefully, before beginning
any operation on the autoclave!
1.1. Manufacturer and US Official Correspondence Information
The Autoclave is manufactured by Tuttnauer Ltd., Located
Har-Tuv B Industrial Zone, P.O. Box 170, Beit Shemesh 9910101,
Israel. Tel: [phone]
The US Official Correspondence is:
Tuttnauer U.S.A Co, Ltd. 25 Power Drive Hauppauge, NY, 11788,
USA. Tel: [phone], Fax: [phone]
1.2. Intended Use
The Elara11 tabletop autoclave is designed for the sterilization of
medical and surgical goods such as wrapped and unwrapped solid,
hollow, and porous loads used in healthcare facilities (e.g., hospitals,
nursing homes, extended care facilities, freestanding surgical centers,
clinics, and medical & dental clinics).
1.3. Intended Users
The Elara11 tabletop autoclave is intended for use by hospital
personnel and other medical personnel.
All autoclave users must receive training in proper usage from an
experienced employee. Every new employee must undergo a training
period from an experienced employee.
1.4. Incoming Inspection
Upon receiving your Tuttnauer Autoclave, carefully inspect the outside
of the shipping carton for signs of damage. If any damage to the carton
is found, note the location with respect to the autoclave and check that
area of the autoclave carefully once it is fully unpacked. Observe
packing method and retain packing materials until the unit has been
inspected. Mechanical inspection involves checking f o r signs of
physical d a m a g e such as: scratched panel surfaces, broken knobs,
etc.
If any damage is found, contact your dealer as soon as possible
so that they can file a claim with the shipping carrier and notify
Tuttnauer.

Page 4
All Tuttnauer products are carefully inspected prior to shipment and all
reasonable precautions are taken in preparing them for shipment to
assure safe arrival at their destination.
Note: Lifting and carrying should always be done by two people.
1.5. Warranty
Tuttnauer warranties, from the date of purchase, all new Elara11
autoclave for a period of one full year, covering both parts and labor.
This one-year warranty covers defects in materials and workmanship
on every part in the autoclave except door gaskets and HEPA filters
(they are considered wear items).
Tuttnauer warranties the chamber for a period of ten (10) years against
defects in materials and workmanship.
This warranty does not include installation or operator instruction which
are covered in this manual for your convenience, or which can be
provided by your dealer.
This warranty does not apply to any instrument that has been
subjected to improper use or accident, nor shall it extend to
autoclaves that have been repaired or altered outside the factory
without prior authorization from Tuttnauer.
The warranty also does not include routine cleaning or preventive
maintenance, to be performed according to instructions in Sec.
10 (Preventive and Scheduled Maintenance). Tuttnauer’s obligation
is limited to the repair or replacement of parts for the autoclave.
No other warranties or obligations are expressed or implied.
The Autoclave should only be used in a manner described in this
manual!
1.6. Warranty Statement
To activate the warranty, the registration card must be completed and
mailed or faxed to Tuttnauer within fourteen (14) days of purchase or
you may call our customer service department at the number listed
below.
Products will only be received and accepted for repair from an
authorized dealer and only with prior return authorization from
Tuttnauer. All transportation charges to and from Tuttnauer must be
paid by the owner of the autoclave. Tuttnauer will not accept COD
shipments. If repairs are needed during the first 90 days after
purchase of this autoclave and a local authorized service dealer is not
available, Tuttnauer will arrange pick up of the unit at Tuttnauer’s
expense. This will be on an individually evaluated basis and ONLY with
pre-approval.
Note: If you have any questions or there are any difficulties with this

Page 5
instrument and the solution is not covered in this manual, please
contact your dealer or Tuttnauer USA Co. Do not attempt to service
this instrument yourself.
Tuttnauer USA Co., Ltd., 25 Power Drive Hauppauge, NY 11788,
USA Tel: [phone], Fax: [phone]
e-mail: [email protected].
1.7. Safety instructions
The autoclave has unique characteristics. Please read and understand
the operation instructions before first operation of the autoclave. This
manual includes instructions and guidance provided by the
manufacturer on: How to properly operate the autoclave, the door
safety mechanism, the dangers involved in circumventing the safety
features, how to ensure that the door is closed, and how to select a
correct sterilization program.
Make sure that you know where the main power switch is located.
Autoclave maintenance is crucial for the correct and efficient function
of the device.
The daily B&D test, at the beginning of the working day, is part of the
preventive maintenance plan, along with the annual validation of the
sterilization processes that ensures appropriate sterilization
conditions.
Never use the autoclave to sterilize liquids since it is not designed for
that purpose.
Never use the autoclave to sterilize corrosive products, such as: acids,
bases and phenols, volatile compounds, or solutions such as
ethanol, methanol, chloroform, or radioactive substances. Below
are the operating instructions –safety instructions:
1. Always operate the autoclave strictly as instructed in this manual.
2. Always wear heat resistant gloves before unloading and avoid touching
hot loads and surfaces.
3. Instruments should not be loaded into the autoclave unless Steam
Sterilization is instructed in their User Manual. The instructed Steam
Sterilization Program should be verified against the programs available
in this autoclave.
4. Before use, check inside the autoclave chamber to ensure that no items
have been left from the previous cycle.
5. Load trays in such a way as to allow steam to move freely among all
items.
6. When sterilizing plastic materials, make sure that the item can withstand
sterilization temperature. Plastic that melts in the chamber is liable to
cause a great deal of damage.
7. On closing the device door, make sure it is properly locked before
activating. Verify that DOOR OPEN symbol is replaced by the
message "System Ready".

Page 6
8. Verify once again that you have chosen the appropriate sterilization
program and the water reservoirs are full.
9. Do not place your hand or head, etc. above the door while opening, as
hot steam is escaping the chamber.
10. Do not stand near the back panel of the autoclave while operating, as
the pressure safety valve may release steam.
11. Do not touch hot surfaces, such as the top enclosure and area adjacent
to the chamber opening!
12. After the cycle, open the door slowly to allow steam to escape and wait
1 minute before you remove the load.
13. To assure proper operation of the autoclave, avoid placing in the
vicinity of electrical equipment which is not certified for Electromagnetic
Compatibility according to IEC/EN 61326-1.
14. A certified inspector must perform a periodic pressure chamber safety
test according to the local regulations.
15. Once a year, or more frequently, effectiveness tests must be
performed, i.e., calibration and validation.
16. Make sure there are no leaks, breaks, blockages, whistles, or strange
noises.
17. Perform the maintenance operations as instructed. The owner of the
autoclave is responsible to perform the maintenance operations.
18. Notify the person in charge immediately of any deviation from the
normal functioning of the device.
19. Protective equipment and clothes and other safety instructions should
be implemented in accordance with local and national regulations and/or
rules!

Page 7
1.8. General Information
This autoclave is an electrically heated sterilizer using steam as a
sterilizing agent.
The Elara11 is designed as a Type B sterilizer in accordance with
EN13060.
The Elara11 is a pre/post-vacuum sterilizer which uses vacuum pulse
technology for removing air from the chamber at the beginning of the
cycle and moisture from the instruments at the end of the cycle. Drying
is performed with the door closed, using a combination of heat and
vacuum.
The advantages of a pre/post-vacuum sterilizer are as follows:
•Removal of residual air from packs and porous load and most kinds of
tubes (rubber, plastic etc.) by vacuum during the first stage of the
cycle.
•More efficient steam penetration into the load; assuring effective
sterilization.
•Improved temperature uniformity throughout the chamber.
•Better drying of materials due to the vacuum achieved in the chamber
during the drying cycle.
1.9. Safety features
The following safety devices are installed in the autoclave to optimize
safe operation and protect operating personnel.
•Two door switches that indicate that the chamber door is fully closed
and latched. Without this indication steam is not introduced into the
chamber.
•An electrical door locking pin that blocks door opening during
operation.
•Two safety thermostats, to prevent over-heating of the steam generator
and the chamber.
•Two safety pressure valves to prevent over-pressurizing the steam
generator or the chamber.
•An advanced control system for monitoring and controlling the process.

Page 8
The Elara11 offers a choice of the following automatic programs
designed to match the material to be sterilized.
Program #
Program Name
Sterilization
Drying
Time
Temp
Time
1
Unwrapped Instruments
273°F
4 min
1 min
2
Wrapped Instruments
273°F
4 min
20 min
3
Unwrapped Delicate Instruments
250°F
20
min
1 min
4
Wrapped Delicate Instruments
250°F
20
min
20 min
Test 1
Vacuum Test
N/A
Pre-set
Test2
Bowie and Dick
273°F
3.5
min
2 min
The Elara11 is validated for use in sterilizing lumened devices of no
longer than 230mm and no smaller than 3.4mm for sterilization
programs 2 and 4.
The Elara11 is validated for use in sterilizing fabric packs/textiles for
sterilization programs 2 and 4.
The Elara11 is validated for use in sterilizing up to six dental
handpieces for sterilization programs 2 and 4.
A computerized control unit ensures a fully automatic sterilization cycle,
control and monitoring of physical parameters and clear documentation
of the sterilization cycle.
The Elara11 features a digital absolute pressure display which is used
for monitoring and control purposes. The device can display the
pressure in psia, psig, kPa, Bar A or Bar G according to the operator’s
requirements. When the pressure is displayed in psig or Bar G, the
atmospheric pressure is shown (at sea level) as 0 psig. If the pressure
is defined in psia, Bar A or kPa the absolute zero is displayed as “0”
and the atmospheric pressure is shown (at sea level) as 14.7 psia, 1
Bar A or 100 kPa respectively.
Note: This unit comes from the factory with the pressure parameter set to
display in psig and the vacuum in inHg.
The Elara11 can display the temperature in ºF or ºC.
Note: The unit comes from the factory set to display temperature in ºF.
The control system is designed to meet the most current sterilization
standards to ensure efficacy, safety of personnel and reliable
operation.

Page 9
A printer is standard on the autoclave. The printer prints the preset and
actual parameters of the cycle (temperature, time, and pressure).
The Elara11 also features built in memory to record up to 100
sterilization cycles. These can be reprinted on the printer or exported to
a USB device to be transferred to a PC.
The Elara11 has a built in Network Port for use with Tuttnauer’s
R.PC.R software when connected to your local network.
The R.PC.R software has been developed especially for the Tuttnauer
autoclaves.
This application will allow you to:
•Monitor up to 8 autoclaves.
•Monitor the real time activity of any autoclave connected via the
network port.
•Manage the history files of the cycles run on your autoclave.
•The history files can be downloaded either directly through a physical
connection to the network port or transferred manually using a
USB device.
•Store all the history of the processes that have been run on your
autoclave.
•Track the parameter setting that have been used in each of the cycles
and stages run.
•Choose the style of the report to view, either graph, table, or a print out
•All reports can be saved as a PDF.
•The graph style report offers the user an option to customize the inputs
and outputs used in the presentation.
For more information on the R.PC.R refer to the R.PC.R user guide.
This manual is intended for the user and gives the user a general
understanding of the instrument and the best ways to operate and take
care of it to obtain effective results.
Before operating this autoclave carefully read this operation manual.
After reading this manual, operating the autoclave will be easy.
However, since this instrument is built with high technology sensitive
components, no attempt should be made by the user or any other
unauthorized person to repair or recalibrate it.
Only technical personnel, of an authorized Tuttnauer dealer,
having proper qualifications and holding technical documentation
(including a technician manual) and adequate information are
authorized to service the apparatus .

Page 10
Read the Operating Instructions carefully, before beginning any
operation on the autoclave!
1.10. Operating Conditions
This device is for indoor use only!
The minimum counter depth for the Elara11 is 24 inches.
Counter tops or slide-outs need to have a minimum capacity of 275 pounds.
The sterilizer should be loaded only with autoclavable material!
Minimum room ventilation shall be 10 cycles per hour.
The environment shall not exceed an ambient temperature range of from 41ºF
(5ºC) to 104ºF (40ºC) and a relative humidity of 85%.
Operate the autoclave only in the manner specified in the manual. If the
equipment is used in a manner not specified by the manufacturer, the
protection provided by the equipment may be impaired.
CAUTION!
Wastewater should be brought into the public net in
accordance with the local rules or requirements
ONLY NON-HAZARDOUS LIQUIDS SHALL BE DISPOSED IN
PUBLIC SEWAGE!

Page 11
1.11. Overall Dimensions

Page 12
1.12. Front View
No.
Description
No.
Description
1
Door microswitches
10
Keypad
2
Autoclave door
11
Printer cover
3
Autoclave outer cover
12
Door opening grip
4
Mineral-free water reservoir
13
Plastic door cover
4a
Water reservoir fill and level gauge
5
Chamber and steam generator
safety valves (inside the reservoir)
14
Autoclave Leg
6
Wastewater reservoir
15
Wastewater drain
7
Display
16
Clean water drain
8
Ventilation grill
17
USB port
9
On/off switch / circuit breaker
18
Printer (standard)
5
4
6
8
9
10
11
14
1
2
3
7
16
15
17
18
12
13
1
4a

Page 13
1.13. Rear View
No.
Description
No.
Description
1
Mineral-free water reservoir
6
RJ45 network port
2
Wastewater reservoir
7
Jacket cut-off thermostat
3
Ventilation grills
8
Generator cut-off thermostat
4
Air filter service cover
9
Main power electric cable socket
5
Wastewater outlet to drain
Warning!
Mind the Power Socket. Keep it and its vicinity dry. Danger of
electrocution.
4
6
1
2
3
5
7
8
9

Page 14
1.14. Specifications
Property
ELARA11
Shipping weight
171 lbs (78 kg)
Maximum weight with instruments full
reservoirs and generator
194.89 lbs (88.4 kg)
Shipping dimensions
(width/height/depth)
W 28.4” * L 32” * H 27.5”
(W 72cm * L 81.2cm * H 70cm)
Shipping volume
14.47 cu ft. (0.41 cu m)
Support area capacity when fully loaded
275 lbs. (125 kg) minimum
Cassette capacity based on 8x11 and
8x5.5 Miltex Thompson cassettes
4 full and 4 half loaded vertically
Minimum counter depth
24’’ (610mm)
Chamber Diameter
11” (280mm)
Chamber Depth
19.8” (504mm)
Chamber volume
7.5 gal. (28.5 lit)
Max. Allowable Working Pressure
(MAWP)
40 psi (2.8 bar)
Maximum instrument load per item
0.7 lbs. (0.3 kg)
Maximum instrument load per tray
3.5 lbs. (1.58 kg)
Maximum solid instrument load
17.6 lbs. (8.0 kg)
Maximum textile load
4.4. lbs. (2.0 kg)
Tray dimensions DxWxH
16.3” * 6.7” * 0.6”
(442mm * 173mm * 19mm)
No. of trays
5
Weight
158 lbs. (71.7 kg)
Mineral-free
water reservoir
Max. water volume
1.375 US gal (5.2 lit)
Min. water volume
0.4 US gal (1.5 lit)
Used (waste)
water reservoir
Max. water volume
0.9 US gal (3.41 lit)
1.15. Steam Generator Data
Property
Value
Max. working pressure
40 psi (2.8 bar)
Safety relief valve
40 psi (2.8 bar)

Page 15
1.16. Autoclave Electrical Data
Property
Value
Total Power
2300W
Voltage
1 or 2 phase, / 230VAC
±5%, 60Hz
Amperage
10A
Protection against electrical
shock
IEC 61010-1
Mains supply fluctuation
+/- 5%
Frequency (Hz)
60Hz
Electrical Circuit
Dedicated electrical circuit
Recommended circuit breaker
15A
1.17. Utilities
Property
Value
Mineral free water
See table in 1.22
Power supply
* 1 or 2 phase, / 230VAC ±5%, 60Hz
Recommended
circuit breaker
15A
* According to the local network.
Cautions!
To avoid any injury by electrical hazard, it is recommended
that a ground fault protection device (GFCI) be installed in
the electrical panel feeding the autoclave (local codes may
make this mandatory).
The electrical network must comply with local rules or
regulations.
Verify that there is an easy access to the main power switch
and to the current leakage safety relay (GFCI). The voltage
supplied to the device must comply with the label ± 5%.
1.18. Environmental Emission Information
•The peak sound level generated by the autoclave is 65dBa with
background noise of 48 dBa.
•The total heat per hour transmitted by the autoclave is <200Wh.
1.19. Construction
The main parts of the autoclave are made of materials as indicated
below:
•Chamber is built of stainless steel 316 L.

Page 16
•Door is made of stainless steel 316.
•Trays are made of stainless steel 304.
•Water reservoir is made of polyethylene.
•Door handle and door cover are made of hard plastic material, which is
safe to touch and thermo-insulated.
1.20. Stickers Description
Symbol
Meaning
Part Number
Location
Pour distilled water into the
reservoir through the opening
on top of the autoclave until it
reaches 1" below the bottom
of the base of the safety
valves.
LAB048-0355
Near the mineral-free
water reservoir cover
Caution! Hot
steam.
LAB048-0058
Near the safety valve
Do not pour water into this
reservoir.
Near the wastewater
reservoir cover
Caution! Consult
accompanying
documents
LAB048-0024
Near the Power switch
PUSH
TO
RESET
Resetting the cut-
off
LAB048-0018
Near the cut-off
Protective Earth
(Ground)
LAB048-0020
Near the on/off switch
Caution: Hot
surface
LAB048-0023
On the top cover above
the door and on the rear
cover above the water
strainer

Page 17
1.21. Symbols Description
Manufacturer
Year of Manufacturing
Medical Device
Model Number
Serial Number
Consult theOperationandMaintenance Manual (User
Manual) before use
Keep away from sunlight and protect from heat.
For Indoor Use Only
Keep dry
Disposal according to electronic scrap ordinance

Page 18
This side up (during transport and shipment)
Fragile (during transport and shipment)
A warning or precaution as detailed in the Operation and
Maintenance Manual (User Manual)
Caution! Hot Surface
Caution! Hot steam
Protective earth (Ground)

Page 19
1.22. Water Quality
The distilled or mineral-free water supply shall be according to the table
below:Suggested maximum limits of contaminants in water for steam
sterilization per EN13060
Substance
Feed Water
Condensate
Evaporate residue
≤ 10 mg/l
≤ 1.0 mg/l
)
2
Silicate (SiO
≤ 1 mg/l
≤ 0.1 mg/l
Iron
≤ 0.2mg/l
≤ 0.1mg/l
Cadmium
≤ 0.005 mg/l
≤ 0.005 mg/l
Lead
≤ 0.05 mg/l
≤ 0.05 mg/l
Rest of heavy metals
except iron,
cadmium, lead
≤ 0.1 mg/l
≤ 0.1 mg/l
Chloride (Cl)
≤ 2 mg/l
≤ 0.1 mg/l
Phosphate
≤ 0.5 mg/l
≤ 0.1 mg/l
Conductivity (at
20°C)
15 µs/cm
≤ 3 µs/cm
pH value
5 to 7.5
5 to 7
Hardness
≤ 0.02 mmol/l
≤ 0.02 mmol/l
Appearance
Colorless, clean, without sediments
Note: The condensate is produced from steam taken from the empty sterilizer
chamber.
Compliance with the above data should be tested in accordance with
acknowledged analytical methods, by an authorized laboratory.
Note:
We recommend testing the water quality once a month. The use of water for
autoclaves that does not comply with the table above may have severe impact
on the working life of the sterilizer and can invalidate the manufacturer’s
guarantee.
Note:
When purchasing distilled water, the label must say “Steam Distilled”.