TV One 1T-VS-622 User manual

Instruction Manual
1T-VS-622
Video to HDMI Scaler

Table of Contents
1.0 Introduction 2
2.0 Specifications 3
3.0 Checking Package Contents 4
4.0 Connecting The Hardware 5
5.0 Operating The Unit 5
6.0 Troubleshooting 7
7.0 Limited Warranty 7
8.0 Regulatory Compliance 8
9.0 Contact Information 8

2
1.0 INTRODUCTION
Thanks for purchasing this 1T-VS-622 Video to HDMI Scaler from TV One. This Scaler
converts analog Composite Video or Component S-Video to a fully compliant HDMI
Output. It also provides audio flexibility by embedding external audio into the HDMI
output signal as well as providing separate Toslink and R/L analog Stereo audio
outputs. Our professional video conversion products have been serving the industry for
over twenty years. TV One offers a full line of high quality Seamless Switchers, Video
Scalers, Up/Down/Cross Converters, Analog-Digital Converters (SD/HD-SDI, HDMI,
DVI), Format Converters, Standards Converters, TBC/Frame Synchronizers, Matrix
Routing Switchers, Signal Distribution Amplifiers and Cat.5 Transmission Systems.
1.1 Liability Statement
Every effort has been made to ensure that this product is free of errors. TV One cannot
be held liable for the use of this hardware or any direct or indirect consequential
damages arising from its use. It is the responsibility of the user of the hardware to check
that it is suitable for his/her requirements and that it is installed correctly. All rights
reserved. No parts of this manual may be reproduced or transmitted by any form or
means electronic or mechanical, including photocopying, recording or by any
information storage or retrieval system without the written consent of the publisher.
TV One reserves the right to revise any of its hardware and software following its policy
to modify and/or improve its products where necessary or desirable. This statement
does not affect the legal rights of the user in any way.
All third party trademarks and copyrights are recognised. The TV One logo, TV One-
task and CORIO are the registered Trademarks of TV One. All other trademarks are the
property of their respective holders.
1.2 Features
•HDMI 1.2 and HDCP 1.1 and DVI 1.0 Compliant
•Toslink Digital Audio 2.0 LPCM
•Accepts either Composite or S-Video Input
•3-D Motion Adaptive, 3-D De-interlacing, 3:2/2:2 Pull Down Detection/Recovery.
•Outputs PC Resolutions up to WUXGA or Video Resolutions from 480i to 1080p
•Automatically detects the resolution of the connected display
•OSD (On Screen Display)
•Adjustment of Contrast, Brightness, Hue, Sat., Sharpness & RGB levels
•Supports digital and analog audio inputs and outputs

3
2.0 SPECIFICATIONS
Video Input/Output
CV or SV Video Input 1x RCA Connector, 1x S-Video Connector
HDMI V1.2 Output 1x via Type A Connector
Video Performance
Standards Compliance HDMI v1.2, HDCP 1.1, DVI 1.0
Output Resolutions PC up to WUXGA, HD up to 1080p
Video Processing 3-D Motion Adaptive, 3-D de-interlacing, 3:2/2:2
Pull Down Detection/Recovery.
Video Adjustments Contrast, Brightness, Hue, Sharpness,
Saturation, R-G-B levels, Picture Size
Audio Inputs/Outputs
Analog Stereo Input 2x via RCA Connectors
Analog Stereo Output 1x via 3.5mm Mini-Stereo Connector
Digital Input (Note 1) 1x SPDIF via Toslink Connector
Digital Output 1x SPDIF via Toslink Connector
Audio Performance
Analog Stereo Input Level 2Vrms max @ 47KΩ
Analog Stereo Output Level Unity @ 47KΩ
Toslink Input/Output Level Standard Toslink level
Analog Stereo Bandwidth 20Hz to 20 KHz
Mechanical
Size (H-W-D) 25x102x145mm (1x4x5.7”)
Weight (Net) 405g (14.2oz)
Warranty
Limited Warranty 2 Years Parts and Labor
Environmental
Operating Temperature 0°to +50°C (+32°to +122°F)
Operating Humidity 10% to 90%, Non-condensing
Storage Temperature -10°to +60°C (+14°to +140°F)
Storage Humidity 10% to 90%, Non-condensing
Power Requirement
External Power Supply [email protected]
Regulatory Approvals
Converter Unit FCC, CE, RoHS
Power Supply UL, CUL, CE, PSE, GS, RoHS
Accessories Included
1x AC Power Adapter US, UK or Euro
1x Operations Manual
Note
(1) Toslink Audio Support is 2.0 LPCM only

4
2.1 Supported Resolutions
INPUTS
Resolutions Television Standard
Composite
& S-Video 480i (480 lines-interlaced) 576i (576 lines-interlaced) NTSC PAL
OUTPUT
Resolution Refresh Rate
PC
VGA
SVGA
XGA
SXGA
UXGA
WXGA
WSXGA
WUXGA
640x480
800x600
1024x768
1280x1024
1600x1200
1280x800
1680x1050
1920x1200
60 Hz
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
HDTV
480p 576p
720p
1080i
1080p
852x480
852x576
1280x720
1920x1080 (i)
1920x1080 (p)
60Hz
50Hz
50, 60Hz
50, 60Hz
50, 60Hz
SDTV 480i
576i 60Hz 50Hz
Note: By default the 1T-VS-622 automatically detects the resolution of the HDMI display
device however you can manually control that selection using the OSD menu structure.
Leave the Resolution in the “Native” position on the OSD menu to enable the Automatic
Detection capability.
3.0 CHECKING PACKAGE CONTENTS
Before attempting to use this unit, please check the packaging and make certain the
following items are contained in the shipping carton:
•1x 1T-VS-622 Video to HDMI Scaler
•1x AC Power Adapter
•1x Operations Manual
Note: Please retain the original packing material should the need arise for return. If you
find any items are missing, contact your reseller or TV One immediately. Have the
Model Number, Serial Number and Invoice available for reference when calling.

5
4.0 CONNECTING THE HARDWARE
Please study the panel drawings below and become familiar with the signal inputs,
outputs, operational controls and the location of the power connector. Next, turn off the
Video source and the HDMI Display and connect the appropriate Video, HDMI and
audio cables, first between the source and the 1T-VS-622 and then between the 1T-VS-
622 and the display. Plug in the provided AC adapter, first to the 1T-VS-622 and then
to an active AC power source. Lastly, turn on the PC source and HDMI display device.
(The 1T-VS-622 has no power switch and will begin to function as soon as it has the AC
adapter connected to it.)
Notes: (1) You may connect either a Composite Video Input or an S-Video input but you
cannot connect both inputs at the same time. The “+” button is used to select which
input is active. (2) The Toslink Input is 2.0 LPCM only.
5.0 OPERATING THE UNIT
The 1T-VS-622 is controlled via an On Screen Display (OSD) menu structure. Much of
the operation of the scaler is done automatically however there may be an occasion
where an adjustment is needed, particularly if the input signals are not presented at
standard levels. Numerous parameters can be controlled from the menu including
adjustment of video parameters, selection of output resolutions and type of audio
output.
The menu structure is shown on the next page and is a two tier arrangement. When you
press the Menu button for the first time, you will be on the top tier. You can then use the
+ and – buttons to move up and down the first tier selections until you arrive at the one
associated with the parameters you wish to adjust. (Note that some of the first tier
parameters have only one associated adjustment -- e.g. BRIGHTNESS -- whereas
others may have several: e.g. OUTPUT.)
When you have reached the parameter you wish to adjust, press the Menu button again
to select that item. If there is only one item in the second tier associated with the
parameter, you can use the + and – buttons to make an adjustment. If there are more
than one item associated with the parameter, use the + and – buttons to move to the
item you wish to adjust, press the Menu button again to select that item and then use
the + and – buttons to make the adjustment.
1T-VS-622 Front Panel 1T-VS-622 Rear Panel

6
Once the adjustment has been made, use the Menu button and + and – buttons to
navigate to where you can exit the OSD.
•XGA Reset: Depressing and holding the Menu button and then the + button
returns the settings to factory defaults and sets the output to XGA.
•480p Reset: Depressing and holding the Menu button and then the - button
returns the settings to factory defaults and sets the output to 480p.
•Input Select Function: To select the active input between Composite Video and
S-Video, press the + button, which toggles between the two inputs.
5.1 Menu Structure
1st Tier Option 2nd Tier Option Adjustment
CONTRAST - 0 ~ 100 of Contrast Level
BRIGHTNESS - 0 ~ 100 of Brightness Level
FINETUNE
- HUE 0 ~ 100 of Hue Level
- SATURATION 0 ~ 100 of Saturation Level
- SHARPNESS 0 ~ 100 of Sharpness Level
- EXIT Back to 1st Tier
COLOR
- RED 0 ~ 100 of Red Color Level
- GREEN 0 ~ 100 of Green Color Level
- BLUE 0 ~ 100 of Blue Color Level
- EXIT Back to 1st Tier
SIZE - FULL / OVERSCAN / UNDERSCAN / LETTERBOX / PANSCAN
OUTPUT -
NATIVE / VGA / SVGA / XGA / SXGA /UXGA / 480i / 480p /
720p@60Hz / 1080i@60Hz /
1080p@60Hz / 576i / 576p /
720p@50Hz / 1080i@50Hz /
1080p@50Hz / WXGA / WSXGA / WUXGA
AUDIO - EAR PHONE / OPTICAL (Source selection)
OSD
- HPOSITION 0 ~ 100 of OSD Horizontal Position
- VPOSITION 0 ~ 100 of OSD Vertical Position
- TIMER 0 ~ 100 of OSD Existing Time (sec.)
- TRANSP 0 ~ 100 of OSD Transparent Level
- EXIT Back to 1st Tier
INFORMATION
SOURCE (Input Interface) INPUT (Input Resolution) OUTPUT (Output Resolution) VERSION (Firmware Version)
EXIT - Close OSD Menu
Reset Function: To reset the unit, press and hold the MENU button then plug the DC
power into the unit. This will reset the unit to factory default.

7
6.0 TROUBLESHOOTING
Faulty cables are the most common problem associated with the 1T-VS-622. Make
certain you are using the highest quality cables available. In the event of trouble with the
unit, inspect the cables for damage and make sure they are completely seated in their
connectors. Also make certain that the AC adapter is plugged in to a working AC
socket and that the LED, located next to the DC connector, is lighted. Finally, if power is
present and the unit does not appear to operate, perform the Reset function described
above. After trying the above suggestions should the problem still persist, contact your
dealer for additional suggestions before contacting TV One. Should the dealer’s
technical personnel be unable to assist you, contact TV One via our support website:
http://tvone.crmdesk.com. Create a technical support request on the site and our
support team will respond within a short period of time.
7.0 LIMITED WARRANTY
LIMITED WARRANTY – With the exceptions noted in the next paragraph, TV One
warrants the original purchaser that the equipment it manufactures or sells will be free
from defects in materials and workmanship for a period of two years from the date of
purchase. Should this product, in TV One’s opinion, prove defective within this warranty
period, TV One, at its option, will repair or replace this product without charge. Any
defective parts replaced become the property of TV One. This warranty does not apply
to those products which have been damaged due to accident, unauthorized alterations,
improper repair, modifications, inadequate maintenance and care, or use in any manner
for which the product was not originally intended. Items integrated into TV One products
that are made by other manufacturers, notably computer hard drives and liquid crystal
display panels, are limited to the term of the warranty offered by the respective
manufacturers. Such specific warranties are available upon request to TV One.
If repairs are necessary under this warranty policy, the original purchaser must obtain a
Return Authorization Number from TV One and return the product to a location
designated by TV One, freight prepaid. After repairs are complete, the product will be
returned, freight prepaid.
LIMITATIONS - All products sold are "as is" and the above Limited Warranty is in lieu of
all other warranties for this product, expressed or implied, and is strictly limited to two
years from the date of purchase. TV One assumes no liability to distributors, resellers or
end-users or any third parties for any loss of use, revenue or profit.
TV One makes no other representation of warranty as to fitness for the purpose or
merchantability or otherwise in respect of any of the products sold. The liability of TV
One with respect to any defective products will be limited to the repair or replacement of
such products. In no event shall TV One be responsible or liable for any damage
arising from the use of such defective products whether such damages be direct,
indirect, consequential or otherwise, and whether such damages are incurred by the
reseller, end-user or any third party.

8
8.0 REGULATORY COMPLIANCE
The 1T-VS-622 has been tested for compliance with appropriate FCC and CE rules and
regulations. The Power Adaptor/Supply has been tested for compliance with appropriate
UL, CUL, CE, PSE, GS Rules, Regulations and/or Guidelines. This Product and Power
Adapter is RoHS Compliant.
9.0 CONTACT INFORMATION
Should you have questions or require assistance with this product in areas not covered
by this manual, please contact TV One at the appropriate location.
TV One USA
1350 Jamike Drive
Erlanger, KY 41018
USA
Tel [phone]
Fax [phone]
[email protected]
www.tvone.com
TV One Europe
Continental Approach
Westwood Industrial Estate
Margate, Kent CT9 4JG, UK
Tel [phone]
Fax [phone]
[email protected]
www.tvone.co.uk
TV One Latin America
2790 NW 79 Ave
Miami, FL 33122
USA
Tel [phone]
Fax [phone]
[email protected]
www.tvonela.com
TV One Mercosur
Honduras 5849, 2nd Floor, Office C
(C1414BNI) Capital Federal
Buenos Aires, Argentina
Tel [phone]
Fax [phone]
[email protected]
www.tvonela.com
TV One Asia
11F, NO.28, Sec. 2
San-Min Rd, Panchiao City
Taipei Hsien 220
Taiwan R.O.C.
Tel [phone]
Fax [phone]
[email protected]
www.tvoneasia.com
TV One China
Rm.9C, Neiwailian Building
No.518 Shangcheng Road
Pudong, Shanghai
China 200120
Tel [phone]
Fax [phone]
Email: [email protected]
Website: www.tvonechina.com
End of Manual