Twinkly Pro TWP-uWiFi User manual

USERGUIDE TWP-uWiFi
REV 1.200601
Smart decoration solutions for professionals

Introduction 3
Package Contents 4
Installation Requirements 5
INSTALLATION PROCESS
Connect to the Ethernet Controller 6
Setting up as Access Point 7
Setting up as Extender 12
TROUBLESHOOTING
Repair Process 14
Restore Process 16
TABLEOF CONTENTS

Thank you for choosing Twinkly Pro for your lighting needs.
This manual will provide detailed instructions, guide you through the entire
setup process, and assist you with the recommended installation procedure
for your device(s).
By reading this step-by-step guide you will:
• avoid making common installation mistakes;
• learn the technical and practical knowledge needed to operate and
manage your device(s) properly;
• minimize the need for Technical Support;
• help create the best experience possible for you and your customers.
decorate like a boss!
Sincerely,
THE TWINKLY PRO TEAM
Introduction
3

4
Package Contents
What is inside the box
1TWP-uWiFi (Accessory for TWPRO1500ETHP)
2Ethernet Cable Extender
1
2

5
Installation Requirements
What is required for the installation *
3TWPRO1500ETHP Controller (up to 7 controllers per Switch)
4TWP-SW-8 (Switch needed only for multi-controller setups)
* purchased separately
3
4

6
STEP 1
Connect to
the Ethernet
Controller

7
Connect the uWiFi to the controller
Plug the Ethernet Controller to a power source
• You can also activate the PoE after connecting the
uWiFi
• Verify the status of the PoE by looking for the
is already activated
Enable the PoE by pressing and holding the button
remain activated even if you disconnect the uWiFi
Wait for the uWiFi to turn on. This process can take up
to 1 minute.
1
2
3

STEP 2A
Setting up as Access Point
SINGLE CONTROLLER SETUP
8
VER TIG O

MULTI-CONTROLLER SETUP
9
VER TIG O
PoE IN
PoE OUT

10
STEP 2A
Setting up as
Access Point
Connect to
192.168.8.1
Select your language
2A.2
Connect via Wi-Fi to
GL-AR150-xxx
The default password
is: goodlife
2A.1
i
i
i
i
i

11
Press Modify
2A.62A.5
Enter your data
Insert the new SSID and
password in the Wi-Fi
Name and Wi-Fi Key,
press Apply. You will
need to reconnect to
the Access Point.
Open Menu and
select Wireless
2A.42A.3
Set your Password
then press Submit

STEP 2B
Setting up as Extender
12
Connect to
192.168.8.1
Enter your
password, then
2B.2
Connect via Wi-Fi to
GL-AR150-xxx
The default password
is: goodlife
2B.1
i
i
i
i
i
VER TIG O

Select Extender
then press Next
2B.62B.5
Select your
network, insert
your password,
press Apply
Under More Settings
select Network Mode
2B.42B.3
Open the Menu
13
all your client devices. When you use Extender mode, you may not
connect to this UI again. You can follow the repair process (page 14) to
1

TROUBLESHOOTING
Repair Process
14
Do this if you cannot connect to
the router or when the router is
page at address 192.168.8.1.
Once the repair has been
performed, the SSID and PW of
the device will not be changed.
uWiFi has to be powered-on
during the process Press and hold for 4
seconds then release,
the router will be
restored to Access
Point
Remove the screws
and lid
4
sec

15
Make sure the
silicone gasket is
sealed before closing
the lid to maintain the
IP rating
Place the cover
and secure it
back with the
screws
...
3G
...
3G
!
Using a PC connect to the uWiFi and connect
to the IP address 192.168.8.1
Select Use as LAN, then press Yes

TROUBLESHOOTING
Restore Process
16
Do this if you want to restore
the device to factory data. It
will be possible to access the
192.168.8.1. Once the reset is
PW will also be restored, see
uWiFi has to be powered-on
during the process Press and hold for
10 seconds then
release, the router will
be restored to factory
settings. All user data
will be cleared.
Remove the screws
and lid
10
sec

17
Make sure the
silicone gasket is
sealed before closing
the lid to maintain the
IP rating
Place the cover
and secure it
back with the
screws
...
3G
...
3G
!
Using a PC connect to the uWiFi and connect
to the IP address 192.168.8.1
Select Use as LAN, then press Yes

FCC ID : 2AFIWGL-AR-150
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
Note 1: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in
a articular installation. If this equipment does cause harmful interference to radio or
user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.

to comply with the requirements setout
in the European Council Directive on the
States relating to RED (2014/53/EU) and RoHS
(2011/65/EU).
This product uses WiFi
RF Exposure: The highest measured 1g
(simultaneous transmission)
Body SAR value is 0.26 W/Kg.
The equipment passed the test which
was performed according to the following
European standards:
ETSI EN301 489-1 V1.9.2 (2011-09)
ETSI EN301 489-3 V1.6.1 (2013-08)
ETSI EN300 328 V1.9.1 (2015-02)
ETSI EN60950-1: 2006+A2:2013
Product based on:
GL-iNet
WHITE
www.gl-inet.com

If you need any further information,
please feel free to contact us:
[email protected]