Tyco AutoPulse Z-10 User manual

Doc. No. 430545
Part No. 579-357
Rev. U
*0579357T*

Blank Page- Back of Front Cover

iii
©2005-2018 Johnson Controls. All rights reserved.
Specifications and other information shown were current as of publication and are subject to
change without notice.
SIMPLEX, and the product names listed in this material are marks and/or registered marks.
Unauthorized use is strictly prohibited.
Copyrights and Trademarks

iv
READ AND SAVE THESE INSTRUCTIONS- Follow the instructions in this installation
manual. These instructions must be followed to avoid damage to this product and associated
equipment. Product operation and reliability depend upon proper installation.
DO NOT INSTALL ANY PRODUCT THAT APPEARS DAMAGED- Upon unpacking,
inspect the contents of the carton for shipping damage. If damage is apparent, immediately file a
claim with the carrier and notify your authorized product supplier.
ELECTRICAL HAZARD -Disconnect electrical field power when making any internal adjust-
ments or repairs. Servicing should be performed by qualified service personnel.
STATIC HAZARD - Static electricity can damage components. Handle as follows:
Ground yourself before opening or installing components.
Prior to installation, keep components wrapped in anti-static material at all times.
EYE SAFETY HAZARD - Under certain fiber optic application conditions, the optical output of
this device may exceed eye safety limits. Do not use magnification (such as a microscope or other
focusing equipment) when viewing the output of this device.
SULFURIC ACID WARNING - the skin and eyes and can destroy fabric. Replace any leaking
or damaged battery while wearing appropriate protective gear. If you come in contact with
sulfuric acid, immediately flush skin or eyes with water for 15 minutes and seek immediate
medical attention.
FCC RULES AND REGULATIONS – PART 15 - This equipment has been tested and found
to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
SYSTEM REACCEPTANCE TEST AFTER SOFTWARE CHANGES -To ensure proper
system operation, this product must be tested in accordance with NFPA72, after any programming
operation or change in site-specific software. Reacceptance testing is required after any change,
addition or deletion of system components, or after any modification, repair or adjustment to
system hardware or wiring.
All components, circuits, system operations, or software functions known to be affected by a
change must be 100% tested. In addition, to ensure that other operations are not inadvertently
affected, at least 10% of initiating devices that are not directly affected by the change, up to a
maximum of 50 devices, must also be tested and proper system operation verified.
Cautions and Warnings

v
This product has been tested and found to comply with the following standards for RF Emissions
& Immunity:
FCC Part 15A
EN55022: 1998, Class A, Emissions (CISPR 22: 1993)
EN50130-4: 1995 EMC
This product has also been tested and found to meet the requirements of EN60950 (1992) “Safety
of Information Technology Equipment Including Electrical Business Equipment”:
+A1:93 + A2:93 + A3:95 + A4:97 + A11:97
This product is listed to the following standards:
UL 864 9th Edition
S527-11 – ULC
FM
CSFM
MEA
Emissions Compliance, Radio Frequency Immunity Safety & Agency
Approvals

vi

vii
Copyrights and Trademarks ........................................................................................... iii
Cautions and Warnings .................................................................................................. iv
Emissions Compliance, Radio Frequency Immunity Safety & Agency Approvals ..........v
Table of Contents .......................................................................................................... vii
Chapter 1 Overview .............................................................................. 1-1
Introduction .............................................................................................................. 1-1
In this Chapter ......................................................................................................... 1-1
Overview – Agent Release and Preaction/Deluge Systems ....................................... 1-2
Fire Suppression Systems....................................................................................... 1-2
Preaction/Deluge Sprinkler Systems ....................................................................... 1-2
Combination Agent Release with Preaction/Deluge Backup................................... 1-2
Supported Applications................................................................................................ 1-3
Pre-Programmed Applications................................................................................. 1-3
Releasing Sequence for Single Detector Activation................................................ 1-8
Releasing Sequence for Dual Detector Activation .................................................. 1-9
Releasing Sequence for Manual Release ............................................................. 1-10
Specifications............................................................................................................. 1-11
Major Panel Components ...................................................................................... 1-11
Optional Modules................................................................................................... 1-13
Depleted Battery Operation ................................................................................... 1-13
Environmental........................................................................................................ 1-13
Listings and Approvals........................................................................................... 1-14
Codes and Standards ............................................................................................ 1-14
Chapter 2 Installing Cabinet and Electronics Assembly.................. 2-1
Introduction .............................................................................................................. 2-1
Required Tools and Hardware................................................................................. 2-1
In this Chapter ......................................................................................................... 2-1
Removing/Installing the Electronics Assembly............................................................ 2-2
Introduction .............................................................................................................. 2-2
Removing Electronics Assembly ............................................................................. 2-2
Installing Electronics Assembly ............................................................................... 2-2
Cutting Conduit Openings ........................................................................................... 2-3
Guidelines................................................................................................................ 2-3
Mounting Cabinet......................................................................................................... 2-4
Introduction .............................................................................................................. 2-4
Guidelines for Locating the Cabinet ........................................................................ 2-4
Surface Mounting..................................................................................................... 2-4
Semi-Flush Mounting............................................................................................... 2-5
Removing and Installing Plastic PCB Cover and Slide-In Labels ............................... 2-6
Removing and Replacing Plastic PCB Cover.......................................................... 2-6
Installing Labels ....................................................................................................... 2-6
Chapter 3 Connecting Field Wiring and AC Power............................ 3-1
Table of Contents

viii
Introduction .............................................................................................................. 3-1
In this Chapter ......................................................................................................... 3-1
Wiring Initiating Device Circuits ................................................................................... 3-2
Guidelines................................................................................................................ 3-2
Field Wiring Connections – Two Wire IDCs ............................................................ 3-4
Wiring Releasing Circuits ............................................................................................ 3-5
Guidelines................................................................................................................ 3-5
Field Wiring Connections......................................................................................... 3-6
Main / Reserve Switch ............................................................................................. 3-6
Key Maintenance Switch ......................................................................................... 3-7
Wiring Special Purpose Monitor Circuits ..................................................................... 3-8
Overview.................................................................................................................. 3-8
Wiring Class A/B SPM Circuits for Single Hazard Applications .............................. 3-8
Wiring Shared, Class B SPM Circuits for Dual Hazard Applications..................... 3-10
Wiring Relay Connections ......................................................................................... 3-11
General Guidelines ................................................................................................ 3-11
Wiring Notification Appliance Circuits........................................................................ 3-12
Guidelines.............................................................................................................. 3-12
Field Wiring Connections....................................................................................... 3-13
Wiring AC Power and Battery Wiring......................................................................... 3-14
Field Wiring for AC Power and Battery Wiring....................................................... 3-14
Enabling Depleted Battery Cutout ......................................................................... 3-15
Battery Maintenance.............................................................................................. 3-16
Wiring 24V Aux Power............................................................................................... 3-17
General .................................................................................................................. 3-17
Wiring Steady, 24 VDC Aux Power ....................................................................... 3-17
Testing Circuit Supervision........................................................................................ 3-18
General .................................................................................................................. 3-18
Earth Fault Detection ............................................................................................. 3-18
Chapter 4 Programming....................................................................... 4-1
Introduction .............................................................................................................. 4-1
In this Chapter ......................................................................................................... 4-1
Overview...................................................................................................................... 4-2
Introduction .............................................................................................................. 4-2
Text-Based Programming........................................................................................ 4-2
Text-Based Programming........................................................................................ 4-3
Front Panel Programming........................................................................................ 4-4
Programming the Application Mode ............................................................................ 4-6
Overview.................................................................................................................. 4-6
Programming the Application Mode, Continued.......................................................... 4-7
Programming the Relay Option ................................................................................... 4-8
Overview.................................................................................................................. 4-8
Programming IDC Circuit Style.................................................................................... 4-9
Overview.................................................................................................................. 4-9
Programming the Automatic Release Timer ............................................................. 4-10
Overview................................................................................................................ 4-10

ix
Programming the RAC Time Limit Cutout ................................................................. 4-11
Overview................................................................................................................ 4-11
Programming the RAC Time Limit Cutout, Continued............................................... 4-12
Programming Manual Release Time Delay............................................................... 4-13
Overview................................................................................................................ 4-13
Programming Abort Switch Operation....................................................................... 4-14
Overview................................................................................................................ 4-14
Programming Stage 1 Alarm NAC2 Coding .............................................................. 4-16
Overview................................................................................................................ 4-16
Programming NAC Operation.................................................................................... 4-17
Overview................................................................................................................ 4-17
Programming Supervisory Operation ........................................................................ 4-18
Overview................................................................................................................ 4-18
Programming Supervisory Operation ........................................................................ 4-19
Overview................................................................................................................ 4-19
Saving and Making Changes..................................................................................... 4-20
Set Program Switch to OFF to Save Changes...................................................... 4-20
Making Changes to an Existing Program .............................................................. 4-20
Recording the Programming Settings.................................................................... 4-20
Chapter 5 Operating .................................................................................1
Introduction ..................................................................................................................1 
In this Chapter .............................................................................................................1
Overview..........................................................................................................................2
LEDs and Keys ............................................................................................................2
Delay Timers................................................................................................................4
Manual Release Switch ...............................................................................................5
Abort Switch.................................................................................................................5
Alarm Clear/Reset .......................................................................................................6
Performing a Lamp Test ..............................................................................................6
Acknowledging Alarms, Troubles, and Supervisory Conditions......................................7
Panel Indications for Alarm, Trouble, Supervisory Condition ......................................7
Acknowledging Alarms ................................................................................................7
Silencing Alarms ..............................................................................................................8 
Procedure ....................................................................................................................8
Resetting the System ......................................................................................................9
Procedure ....................................................................................................................9
Viewing Historical Log/Setting Time and Date ..............................................................10
Procedure ..................................................................................................................10
Appendix A FM System Requirements.................................................11
Introduction ................................................................................................................11
General ......................................................................................................................11
FM Requirements/Approvals .........................................................................................12
Automatic Extinguishing Release Requirements ......................................................12
Preaction/Deluge Applications...................................................................................12

x
Appendix B TEPG-US/Tyco Safety Products UL Part Number Cross
Reference and Approved Valves.............................................................1
Appendix C Battery Selection Calculations ...........................................4
Introduction ..................................................................................................................4 
General ........................................................................................................................4
Battery Selection Calculations.........................................................................................2