TYROLIT Hydrostress WSE1217 User manual

Operating Instructions
Wall saw WSE1217
Index 000
Original operating instructions
10991490 en / 11.08.2015

Page 2
Wall saw WSE1217
TYROLIT Hydrostress AG
Witzbergstrasse 18
CH-8330 Pfäkon
Switzerland
Tel. [phone]
Fax [phone]
Congratulations!
With a Hydrostress unit from TYROLIT, you have chosen a tried and tested piece of equipment
which has been designed and built to leading technical standards. Only genuine TYROLIT Hy-
drostress replacement parts can guarantee quality and interchangeability. If maintenance work
is neglected or carried out inexpertly we will be unable to honour our warranty obligations. Any
repair work must be carried out by trained personnel only.
Our aftersales service is available to help ensure that your TYROLIT Hydrostress units remain in
perfect working order.
We hope that working with your TYROLIT unit will be a satisfying and fault-free experience.
TYROLIT Hydrostress
Copyright © TYROLIT Hydrostress

TYROLIT Hydrostress AG
Page 3
Wall saw WSE1217
Safety
These instructions are just one part of the documentation which is supplied together with the
wall saw. These instructions go together with the «Safety Manual / System Description for Wall
Saws» to form a complete set of documentation.
DANGER
Failure to comply with the safety instructions in the "Safety Manual / System Handbook" may
result in serious injury or even death.
XPlease ensure that the «Safety Manual / System Description for Wall Saws» has been read and
understood in full.
DANGER
Cuts from the saw blade.
XAlways wear protective gloves when working on the wall saw, particularly when working on
the saw blade.
XAlways use the blade guard when operating the wall saw.
DANGER
Serious injury or material damage as a result of uncontrolled movements of the wall saw.
XNever connect or disconnect cables when the control unit is switched on.
1

TYROLIT Hydrostress AG
Page 4
Wall saw WSE1217
Description
Wall saw system
The design and function of the wall saw systems are described in the “Safety Manual /
System Description for Wall Saws”.
Wall saw
Components
1 Guide roller 10 Feed motor cable
2 Lock unit 11 Chassis
3 Water supply line 12 Carrying handle / lock unit
4 Blade guard holder 13 Identication plate - Blade drive motor
5 Geared swivel arm 14 Blade drive motor
6 Water - Bypass 15 Feed motor, travel
7 Saw blade holder 16 Water connection
8 Carrying handle 17 Feed motor, swivel
9 Blade drive motor cable
2
2.1
2.2

TYROLIT Hydrostress AG
Page 5
Wall saw WSE1217
Assembly / Disassembly
Place the wall saw on the guide rail
1.
2. If the grips fail to engage or the wall saw sits too loosely on the guide rail: adjust the guide
rollers.
Adjusting the guide rollers
X
* The guide rollers are set correctly when they align in the guide groove and it is possible to
turn them by hand.
3
3.1
3.2

TYROLIT Hydrostress AG
Page 6
Wall saw WSE1217
Mounting the drive motor
X
Mounting the saw blade
DANGER
It can cause death or serious injury if the saw blade ies away.
XOnly use original screws and bolts from TYROLIT Hydrostress AG.
DANGER
Serious injury can be caused by sudden start-up of the saw blade.
XSwitch o the control unit before working on the saw blade.
XIsolate the control unit from the mains supply.
Preparations for assembly
XDuring initial installation, remove the ush cut anchoring screws on the quick-release ange.
3.3
3.4
3.4.1

TYROLIT Hydrostress AG
Page 7
Wall saw WSE1217
Preassemble the saw blade unit
The direction of rotation of the saw blade must match the direction of rotation of the machine.
Correct alignment: Countersinking of the fastening holes against the blade cover.
For normal cuts with saw blades up to Ø 1,000 mm
X
For normal cuts with saw blades bigger than Ø 1,000 mm
X
3.4.2

TYROLIT Hydrostress AG
Page 8
Wall saw WSE1217
For ush cuts
X
Fastening the saw blade unit
DANGER
It can cause death or serious injury if the saw blade ies away.
XCheck whether the sleeve and central screw are countersunk.
XTighten the central screw to a torque of 60 Nm.
X
3.4.3

TYROLIT Hydrostress AG
Page 9
Wall saw WSE1217
Removing the saw blade unit
WARNING
Injuries can be caused if the saw blade drops down.
XLift out the saw blade unit to the top when removing it.
1.
2. Disassemble the saw blade unit in the reverse order to the assembly process.
Mounting the blade guard
XMount the blade guard according to the instruction leaet.
3.5
3.6

TYROLIT Hydrostress AG
Page 10
Wall saw WSE1217
Connecting the wall saw to the control unit
9The control unit is isolated from the power supply.
9Connectors/plugs are clean.
9Cables are undamaged.
X
3.7