U-Reach SATA DOM Duplicator User manual

www.ureach-inc.com
the Expert of Duplicators
SATA DOM
Duplicator
User Guide
V1.0

2
Disclaimer of Warranties
Disclaimer of Warranties
All UREACH flash duplicators are made specifically for data backup with legal
authorities from copyright owners. Any unauthorized action of copyright is
strictly prohibited, and UREACH-INC disclaims all warranties or representations
of illegal actions by users.
UREACH-INC also disclaims any liability for any loss or damage due to
not being able to perform its undertakings or provide any of the services
attributable to any events or circumstances beyond our control. Users agree
and accept all statements above as soon as purchasing our products.
This manual contains materials that should be intended for personal use. All
right reserved. No part of this manual may be reproduced, transmitted or
transcribed without the expressed written permission of the manufacturer .The
information present in this manual is subject to change without prior notice.

3
Before you start
Important Notice
• Read the complete operation instruction carefully contributes to better
operation.
• Make sure the source device is correct and workable.
• To guarantee data consistency, it is strongly suggested that the capacity of
source and targets should be the same.
• It is strongly suggest to use “Copy+Compare” to achieve perfect duplication.
Safety Precautions
• The warranty will expire if damage is incurred resulting from non-compliance
with theses operating instructions.
• Never turn off the power while processing the firmware update.
• Use only approved power sources.
• The product is only suitable for operation in dry, dust free, clean
environment.
• Do not allow liquids or foreign objects to enter. Failure to do so may severely
damage your duplicator.

4
Index Content
▪
Disclaimer of Warranties 2
▪
Before you start 3
▪
Index Content 4
♳
Introduction
1. Overview 5
2. Features 5
3. Package Contents 6
4. Product Overview 7
5. Other adapters that can be
applied 8
♴
Function Table 9
♵
Function Introduction
1. Copy 11
2. Compare 12
3. Copy+Compare 12
4. Erase 12
4.1 Quick Erase 13
4.2 Full Erase 13
4.3 DoD Erase 13
4.4 DoD Erase Comp 14
5. Utility 14
5.1 Show DOM Info. 14
5.2 Update System 15
5.3 System Info. 15
6. Setup 16
6.1 Copy Area 16
6.1.1 System and Files 16
6.1.2 All Partitions 16
6.1.3 Whole HDD 17
6.2 Skip Error 18
6.3 Erase Master 18
6.4 Unknown Format 18
6.4.1 Copy Unknown 18
6.4.2 Skip Unknown 19
6.5 Transfer Rate 19
6.6 Erase Pattern 19
6.6.1 ONE Byte 19
6.6.2 4MB Byte 19
6.7 Language 20
6.8 Restore Default 20
♶
FAQ 21
♷
Specification 22

Introduction 1
5
Introduction
1.Overview
This duplicator series is a high-end industrial standard SATA DOM duplicator
that makes DOM duplication fast and easy. There is no computer or additional
software required. It supports 1 to 7 targets duplication and high data transfer
speed up to 3.9GB per minute. The three different copy modes (System and Files,
All Partitions and Whole HDD) can satisfy various needs of duplication; "System
and Files" copy mode is a fast copy mode that can copy only data area instead of
copying entire source HDD, so it can greatly save elapsing time.
This series supports lots of interfaces including SATA DOM, mSATA, Micro SATA,
CF, CFast through suitable adapters, which makes this product applicable on lots
of different devices. In addition, it provides smart power control system. When
copying is finished, the machine will automatically cut off the power of each port
to protect HDD from damage during removal from the duplicator. The power of
each port will be only be output when the operation is started. Besides Quick/Full
Erase, it provides with DoD Erase and DoD EraseComp, which can completely
erase the data from hard drives complying with Department of Defense standard
(DoD 5220) and guarantee the data was completely deleted.
2.Features
• Support high transmission speed up to 3.9GB/Min.
• Support many kinds of interfaces including SATA, mSATA, MicroSATA, CF, and
CFast through adapters.
• Automatic power control to protect HDD from the damage during insertion and
removal.
• Standalone, no PC or other installation required.
• Three duplication modes: “System and Files”, “All Partitions”, and “Whole HDD”
copy modes.
• Instant power on and o. Easy to boot up without waiting time.
• Easy rmware updating without complex procedure.
• Support DoD Erase function which complies with the standard of Department
of Defense.

1 Introduction
6
3.Package Contents
Power Adapter/Power Cord
SATA DOM Adapter
SATA DOM Duplicator
User Guide

Introduction 1
7
4.Product Overview
A. System Overview
Back Side
Power Supply
Power Switch
Socket
Yellow: Powering
Green Flashing: Processing
Green Remaining: Pass
Red: Fail
LCD
Up Side
B. LCD Configuration
Forward
Backward
Confirm/OK
Cancel/Back

1 Introduction
8
5.Other adapters that can be applied
Adapter
mSATA ↑SATA MicroSATA ↑SATA CF ↑SATA CFast ↑SATA
Device
supported

Function Table 2
9
Function Table
Function Description
1. Copy To copy source DOM to multiple target DOMs. Refer to function “6.1
Copy Area” for 3 different copy mode selection.
2. Compare To compare data bit for bit between source and copied DOMs.
3. Copy+Compare It makes copy first and then compare copied DOM with source
DOM to ensure copied correctness.
4. Erase
Note: Function 6.3
can select to erase
source DOM or not
4.1 Quick Erase
Erase DOM’s index table only, it takes short time to execute this
function.
4.2 Full Erase
Erase the whole DOM content.
4.3 DoD erase
Erase DOMs three times complying with USA Department of
Defense (DoD) standard.
4.4 DoD EraseComp
Erase DOMs three times complying with USA Department of
Defense (DoD) standard, and compare data bit by bit to check if
data is completely erased.
5. Utility
5.1 Show DOM info.
Shows DOM’s basic information such as DOM’S model name and
capacity.
5.2 Update System
5.2.1 Update BIOS
To update the system firmware via the DOM.
5.2.2 Create Update HDD
To format the DOM with a 2GB FAT partition
in order to quickly save firmware in the
DOM.
5.3 System Info.
This function will show information of the duplicator system,
including controller model number and software version.

2 Function Table
10
6. Setup
6.1 Copy Area
Setup copy mode.
6.1.1 System and files
Set to copy source HDD’s data area only.
6.1.2 ALL partition
Set to copy source HDD’s all partitions.
6.1.3 Whole HDD
Set to copy the whole source HDD.
6.2 Skip Error
Set the error volume of source DOM that you want to ignore while
copying. (0 - 65535)
6.3 Erase Master
Setup to erase
source DOM or
not.
6.3.1 Disable
Disable erase source DOM.
6.3.2 Enable
Enable erase source DOM.
6.4 Unknown
Format
6.4.1 Copy unknown
Copy unknown area when the device can not
identifythe format.
6.4.2 Skip unknown
Skip copying unknown area when the device
can notidentify the format.
6.5 Transfer Rate
Select the proper transfer rate UDMA 2 - 4. 4 is the fastest.
6.6 Erase Pattern
6.6.1 ONE Byte
A random character to be written into every
byte.
6.6.2 4MB Byte
A set of random characters to be written into
a set of area.
6.7 Language
Select preferred language.
6.8 Restore Default
Back to original manufacturer setting.

Function Introduction 3
11
Function Introduction
1.Copy
It copies data from source DOM to target DOM. Please make sure you have
chosen the correct copy mode you would like to use. About the three copy
modes, please refer to function [6.1 Copy Area] for details.
DOM Duplicator
1.Copy
The default setting of [6.1 Copy Area] is “System and Files”.
Steps
a. Plug in the source DOM and target DOMs, and then select function
[1. Copy].
Copy
Searching Source
Analyzing Source
Copy 21.9G
2 readyTarget
Copy 967M
1 readyTarget
Copy
Searching Source
Analyzing Source
Copy 21.9G
2 readyTarget
Copy 967M
1 readyTarget
b. After finishing analyzing the source and all the targets are ready, the
system will start copying automatically.
Copy X 2 21.9G
15:5 82% (3)18.0G
Function Total data size
Copied
data size
Copied time
and %
The slowest
port

3 Function Introduction
12
c. When finishing copying, the copied result will be showed on the LCD.
Pass: 2 Fail: 0
Time 19:19
Quantity of copy pass Quantity of copy fail
Total copied time
2.Compare
This function is used to check the correctness of the copying result. After
finishing copying, go to function 2 and press OK to start executing comparing
process.
DOM Duplicator
2.Compare
3.Copy+Compare
This function makes copy first and then compare copied target DOM with the
source DOM automatically to ensure the correctness of the copied result.
4.Erase
This function is used to delete the data in your DOM. Please choose the
appropriate erase method when you would like to dispose or reuse the DOMs.
DOM Duplicator
4. Erase
1.Function [6.3 Erase Master] is to determine if erasing source
DOM or not. The default setting is “Disable erase master ”.
2.The function can be stopped while processing by pressing
[ESC] for about 3~4 seconds.

Function Introduction 3
13
4.1 Quick Erase
The function will ONLY erase the index of the DOM, which is the quickest way
to erase it. Quick Erase will damage the data in DOM, please make sure you
have backup all important data before using this function.
4.2 Full Erase
The function will erase the whole sectors on the target DOM. It will take longer
time than quick erase. Full Erase will damage the data in DOM, please make
sure you have backup all important data before using this function.
4.3 DoD Erase
DoD Erase is an erasing method that complies with the U.S.A. Department
of Defense (DoD) standard. It can guarantee the data was fully deleted by
erasing the DOM bit by bit three times. DoD Erase will damage the data in
DOM, please make sure you have backup all important data before using this
function.
Steps
a. Press OK to execute erasing.
DoD Erase
Prepare Pattern
Erasing HDD
DoD Erase 5:52
b. The result will be showed on the LCD when DoD Erase is finished.
DoD Erase
Pass:2 Fail:0

3 Function Introduction
14
4.4 DoD Erase Comp
Besides DoD erase, this function will also execute compare function
to make sure the random bit was correctly written. This way of erase
is to erase DOM over each sector three times: the first time
with zeros (0x00), second time with 0xFF and the third time with
random characters. There is one final pass to compare random
characters by reading. This function will damage the data in DOM, please
make sure you have backup all important data before using this function.
step1. 0x00100GB
20GB
20GB
20GB
40GB
step2. 0xFF step3. Random step4. Compare
※The erasing time of DoD Erase mode is three times longer than Full Erase mode,
and the time of DoD Erase Comp is four times longer than Full Erase mode.
5.Utility
5.1 Show DOM Info.
This function will show DOM's basic information such as DOM capacity and
model number.
[01]64G
TS1GSDOM22V
Port No.
DOM Capacity
DOM mode No.

Function Introduction 3
15
5.2 Update System
This function is used to update the system firmware. Please follow the following
steps to execute “Update System”.
a. Select function [5.2.2 Create Update HDD].
[Update System]
2.Create Update HDD
b. Format DOM.(Create a 2GB FAT partition)
Do FORMAT HDD#1
Confirm ?
The purpose of formatting DOM before updating system
is because creating a 2GB FAT partition can speed up the
updating process.
c. Download the BIOS from PC to your DOM.
d. Plug in the DOM into the Port#1, and select [Function 5.2.1] to update
BIOS.
5.3 System Info.
This function shows the information of the duplicator including model name
and firmware version.
DOM Dupe 1-7
Ver: 2.29.7

3 Function Introduction
16
6.Setup
6.1 Copy Area
6.1.1 System and Files
It will copy source DOM’s System and Files instead of the whole HDD. The
system will analyze the source HDD and identify the data area to copy. As
long as the source DOM’s data within the target HDD’s space, the copy will be
processed.
[Copy Area]
System and Files
When choosing “System and Files Copy”,only 20G data will be copied,
and it just takes 6.2% time compared to “Whole HDD Copy’.
The target HDD will be exactly the same as source HDD after copy.
[System and Files] only supports FAT, NTFS and LINUX EXT2/
EXT3/EXT4 for quick copy.
6.1.2 All Partitions
This mode will copy all of the partitions bit by bit including the free space. The
capacity of target HDD has to be larger than all the partitions.
[Copy Area]
All Partitions

Function Introduction 3
17
When choosing “All Partitions Copy”,only 120G data will be copied,
and it just takes 37.5% time compared to “Whole HDD Copy’.
The target HDD will be exactly the same as source HDD after copy.
6.1.3 Whole HDD
This mode will copy the entire HDD, regardless of the content, format, partition,
or free space, and it will take much more time to duplicate the source DOM
completely.
[Copy Area]
Whole HDD
When choosing “Whole HDD Copy”,completed 320G HDD will be
copied,and it just takes the longest time.
The target HDD will be exactly the same as source HDD after copy.
After copy, the remaining space in the copied DOM can be
used by PC for further partitioning.

3 Function Introduction
18
6.2 Skip Error
This function can set the number of errors you would like to skip during the
copying process.
[Skip Error]
0
If the DOM is very critical for content correctness, it is strongly
recommended to keep the Skip Error to be“0”.
6.3 Erase Master
This function is used to set if erasing the source DOM or not. Please make sure
this setting before you execute erase function.
[Erase Master]
Disable
[Erase Master]
Enable
6.4 Unknown Format
This function is used to set if copying the unknown format area or not.
6.4.1 Copy Unknown
This setting allows copying the unknown area that the system can’t identify its
format.
[Unknown Format]
Copy Unknown

Function Introduction 3
19
6.4.2 Skip Unknown
This setting is to skip the unknown area that the system can’t identify its format
during the copying process.
[Unknown Format]
Skip Unknown
6.5 Transfer Rate
You can select the best transfer rate from UDMA 2 to UDMA 4 for your DOM
duplication progress. If you are not confident on the DOM quality or you find
a high failure rate on copy or compare. It is recommended to slow down the
UDMA mode.
[Transfer Rate]
UDMA 3
6.6 Erase Pattern
This setting is used to select different erase methods.
6.6.1 ONE Byte
A random character to be written into every byte.
[Erase Pattern]
One Byte
6.6.2 4MB Byte
A set of random character to be written into a set of area.
[Erase Pattern]
4MB Byte

3 Function Introduction
20
6.7 Language
This setting is to set the system’s language interface.
[Language]
English
6.8 Restore Default
This setting is to go back to the manufacturer’s default setting.