U-Reach Legend Series User manual

HDD Duplicator
LE600
User Guide V2.1
Legend Series
EN
English

Disclaimer of Warranties
2
Disclaimer of Warranties
All duplicators are made specically for data backup with legal authorities from
copyright owners. Any unauthorized action of copyright is strictly prohibited,
and manufacturer disclaims all warranties or representations of illegal actions
by users.
Manufacturer also disclaims any liability for any of losses or damages due to not
be able to perform its undertakings or provide any of the services attributable
to any events or circumstances beyond our control. Users agree and accept all
statements above as soon as purchasing our products.
This manual contains materials should be intended for personal use. All right
reserved. No part of this manual may be reproduced, transmitted or transcribed
without the expressed written permission of the manufacturer.The information
present in this manual is subject to change without prior notice.

Before you start
3
Important Notice
●Read the complete operation instruction carefully contributes to better
operation.
●Make sure the source device is correct and workable.
●To guarantee data consistency, strongly suggest the capacity of source and
targets should be the same.
●It is strongly suggest to use "Copy+Compare" to achieve perfect duplication.
Safety Precautions
●The warranty will expire if damage is incurred resulting from non-compliance
with theses operating instructions.
●Never turn off the power while processing the rmware update.
●Use only approved power sources.
●The product is only suitable for operation in dry, dust free, clean
environment.
Do not allow liquids or foreign objects to enter. Failure to do so may severely
damage your duplicator.

Content Index
4
Disclaimer of Warranties 2
Important Notice 3
Safety Precautions 3
1Introduction
1. Introduction 5
1.1 Features 5
1.2 Product Overview 6
A. System Overview 6
B. LCD Conguration 6
C. Free-Chained Legend Series 7
1.3 Optional Accessories 7
2Function Table
Function Table 8
3Function Introduction
1. Copy 10
2. Compare 11
3. Copy+Compare 11
4. Erase 11
4.1 Quick Erase 12
4.2 Full Erase 12
4.3 DoD Erase 12
4.4 DoD Erase Comp 13
4.5 Secure Erase 13
5. Utility 13
5.1 Show Disk Info. 13
5.2 Update System 14
5.3 System Info. 14
6. Setup 15
6.1 Copy Area 15
6.1.1 System and Files 15
6.1.2 All Partitions 15
6.1.3 Whole HDD 16
6.1.4 Percentage(%) 17
6.2 Skip Error 17
6.3 Language 18
6.4 Advanced Setup 18
6.4.1 Unknown Format 18
6.4.1.1 Copy Unknown 18
6.4.1.2 Skip Unknown 18
6.4.2 Erase Master 18
6.4.3 Erase Pattern 19
6.4.3.1 ONE Byte 19
6.4.3.2 4MB Byte 19
6.4.4 Wait HDD Time 19
6.4.5 Transfer Rate 20
6.4.6 Stop Motor Time 20
6.5 Restore Default 20
4Specification
Specication 21

1Introduction
5
1. Introduction
1-1. Features
●High speed up to 3.9GB/min. for Legend 600 series.
●"Free-Chain" technology makes production more efficient as more
duplicators are hooked up! By a simple connection, many 3-target HDD
duplicator duplicators can become one 119-target duplicator at maximum.
●Compatible with various file system formats (including 15TB advanced
format HDD), and supports HDDs with capacity larger than 15TB.
●Four duplication modes: "System and Files", "All Partition", "Whole HDD"
copy modes, and Percentage copy.
●By adding a variety of optional adapter cards, Legend 600 becomes a
superman that can supporting mSATA, microSATA, eSATA, USB3.0, CF,
iVDR, and 2.5”/3.5” IDE.
●Automatic power control to protect HDD from damage during insertion and
removal.
●Standalone, no PC or other installation required.
●Instant power on and off. Easy to boot up without waiting time.

1Introduction
6
1-2. Product Overview
A. System Overview
Front Side
LCD
Socket
Red : Fail
Green : Pass
Yellow : Powering
Back Side
Power Supply Input
Power Switch Output
B. LCD Configuration
Forward
Total size
Copied processed size
Function
Time(mm:ss)
Number of target HDD
Conrm/OK
Cancel/Back
Backward
Copy progress %

1Introduction
7
C. Free-Chained Legend Series
Input
Free-Chain Cable
Output
Users can use free-chain to connect Legend Series.
The maximum connected volume is thirty, which will become 1 to 119 targets.
1-3. Optional Accessories
2.5" to 3.5" IDE Adapter
mSATA Adapter
eSATA to SATA Adapter
CF Card to SATA Adapter
3.5" IDE to SATA Adapter
IVDR to SATA Adapter
SD Card to SATA Adapter
Micro SATA Adapter

2Function Table
8
Function Description
1. Copy To copy source HDD to multiple target HDDs. Refer to function 6.Setup for 3 different copy
mode selection.
2. Compare To compare data bit for bit between source and copied HDDs.
3. Copy+Compare It makes copy first and then compare copied HDD with source HDD to ensure data
correctness.
4. Erase
Note:
Function 6.4.3 can
select to erase
source HDD or not.
4.1 Quick Erase
Erase HDD’s index table only, it takes short time to execute this function.
4.2 Full Erase
Erase the whole HDD content.
4.3 DoD Erase
Erase HDDs three times complying with USA Department of Defense (DoD) standard.
4.4 DoD EraseComp
Erase HDDs three times complying with n USA Department of Defense (DoD) standard and bit
by bit to check if data is completely erased.
4.5 Secure Erase
The international authorized high standard Secure Erase function. It is able to erase the area
which is not loadable.
5. Utility
5.1 Show Disk info
Shows HDD’s basic information such as HDD model name and capacity.
5.2 Update System
5.2.1 Update BIOS
To update the system rmware via the HDD.
5.2.2 Create Update HDD
To format the HDD with a 2GB FAT partition in order to quickly save
rmware in the HDD.
5.3 System Info
This function will show information of the duplicator system, including controller model, number
and software version.

2Function Table
9
6. Setup
6.1 Copy Area
Setup copy mode.
6.1.1 System and les
Set to copy source HDD's data area only.
6.1.2 ALL Partitions
Set to copy source HDD's all partitions.
6.1.3 Whole HDD
Set to copy the whole source HDD.
6.1.4 Percentage (%)
Sets percentage range of HDD for copy.
6.2 Skip Error
Set to ignore error of source HDD while copying.
(0 -100 Set to ignore error of source HDD.)
6.3 Language
Select preferred language. (Chinese and English are available for selection)
6.4 Advanced Setup
6.4.1 Copy Unknown
Format
6.4.1.1 Copy unknown
Copy unknown area when the device can not
identify the format.
6.4.1.2 Skip unknown
Skip copy unknown area when the device can
not identify the format.
6.4.2 Erase Master
Setup to erase source
HDD or not.
6.4.2.1 Disable
Disable erase source HDD.
6.4.2.2 Enable
Enable erase source HDD.
6.4.3 Erase Pattern
6.4.3.1 ONE Byte
A random character to be written into every
byte.
6.4.3.2 Big Random Data
A set of random character to be written into a
set of area.
6.4.4 Wait HD Time
Auto start time after plugging in HDD. Able to set from 0 to 30
seconds.
6.4.5 Transfer Rate
Select the proper transfer rate UDMA2-7. 7 is the fastest.
6.4.6 Stop Motor Time
To set the time waited for the motor to stop from 1-~20 seconds after
executing funciotn.
6.5 Restore Default
Back to original manufacturer setting.

3Function Introduction
10
1. Copy
It copies data from source HDD to target HDDs. Please make sure you have
chosen correct copy mode you would like to use, about the three copy modes
please refer to function [6.1 Copy Area] for details.
Note:
The default setting of [6.1 Copy Area] is "System and Files".
Steps
①Plug in the source HDD and target HDDs, and then select function [1. Copy].
②After nishing analyzing the source and all the targets are ready, press OK to
start or the system will start copying automatically.
Total data size
Copied data size
Function
Copy time and %